Download Marantz MM9360 Operating instructions
Transcript
CH1 (1-2 MONO) 4 3 CH 2 5 4 6 8 2 1 7 9 0 8 2 1 10 4 CH5 7 10 3 8 1 9 10 0 CH 6 (1-2 MONO) 4 5 6 6 2 9 0 5 3 7 STEREO BRIDG E MO NO PUSH PUSH CH 4 3 8 1 10 CH3 (1-2 MONO) 4 5 6 6 2 9 0 5 3 7 4 8 2 1 7 8 1 10 9 10 0 STEREO BRIDG E MO NO P U SH 6 2 9 0 5 3 7 STEREO BRIDG E MO NO P U SH P U SH CAUTION MODEL NO. MM9360 P U SH 115V RISKOFELECTRICSHOCK DONOTOPEN 50/60Hz 1400W B R ID G E M O D E S T E R E O M O DE 150W / C H A N - 8 OH M S 250W / C H A N - 4 OH M S C H 1 (MONO) CH 2 C H 3 (MONO) CH 4 C H 5 (MONO) CH 6 D C TR IG G ER R C -5 R E M O T E C O NT R OL IN OU T CH2 CH3 CH4 CH5 CH6 + IN O UT PU TS B R ID G E B R ID G E CH1 T AK E OU T PU T F RO M T W O RE D PO ST S D O N OT C ON NE C T EIT HE R OU T PU T W IR E T O GR OU ND B R ID G E M O D E 500W B RID GE - 8 OH M S - + B R ID G E - + - OU T R E PLA C E O N L Y W IT H SA M E TY PE FUSE R E FER TO O W N ER 'S M A N U A L FO R PRO P ER FU SE RA T ING AC (+ ) (+ ) (+ ) (+ ) (+ ) CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 (+ ) (-) (-) (-) (-) (-) (-) M A N U F A C T U R E D IN T H E U S A B Y A S H L Y A U D IO IN C O R P O R A T E D To Power Outlet Front Surround Center -L- -L- Center Out Marantz Remote Control L R Front L R Surround Cen Sub Center Typical Surround Preamplifier Outputs Typical Wiring Diagram - + - - + - + Sub -R- -R- - + + - + 4. SPEAKER CONNECTIONS 6. CARE AND MAINTENANCE This equipment, being a high audio output power ampli- This section describes the car and maintenance tasks that fier, has a hazardous energy at its speaker terminal. Please be sure to make an appropriate speaker connection according to the following procedure: must be performed to optimize the operation of your marantz equipment. - Confirm that the power switch of the equipment is at "OFF" position. If it is at "ON", turn it to "OFF" position to connect a speaker cable. - Use a speaker cable with the flame retardant rating of type SPT12 or more. - For bare wire connections, strip the insulation off no more than 3/8" at the speaker terminal connection of speaker cable, and twist the exposed wire. For banana-type plugs or spade terminals, follow the instructions of the connector manufacturer. - Connect speakers in correct polarity, according to the indication for the polarity of speaker terminals. For bare wire or spade terminal connections, first loosen the speaker CLEANING OF EQUIPMENT EXTERNAL SURFACES The exterior finish of your unit will last indefinitely with proper care and cleaning. Never use scouring pads, steel wool, scouring powders or harsh chemical agents (e.g. lye solution), alcohol, thinners, benzine insecticide or other volatile substances as these will mar the finish of the equipment. Likewise, never use cloths containing chemical substances. If the equipment gets dirty, wipe the external surface with a soft, lint free cloth. If the equipment becomes heavily soiled: - Dilute some washing up liquid in water, in a ratio of one part detergent to six parts water. terminal by turning in a counter-clockwise direction, insert the bare wire or spade terminal, then re-tighten by turning the terminal clockwise. - Dip a soft, lint free cloth in the solution and wring the cloth out until it is damp. - Prevent any stress from being applied to the speaker cable - Dry the equipment by wiping it with a dry cloth. - Wipe the equipment with the damp cloth. connected to the speaker terminal. - Don't touch the speaker terminals during operation. 7