Download Marantz MM9360 Operating instructions

Transcript
CH1
(1-2 MONO)
4
3
CH 2
5
4
6
8
2
1
7
9
0
8
2
1
10
4
CH5
7
10
3
8
1
9
10
0
CH 6
(1-2 MONO)
4 5 6
6
2
9
0
5
3
7
STEREO
BRIDG E MO NO
PUSH
PUSH
CH 4
3
8
1
10
CH3
(1-2 MONO)
4 5 6
6
2
9
0
5
3
7
4
8
2
1
7
8
1
10
9
10
0
STEREO
BRIDG E MO NO
P U SH
6
2
9
0
5
3
7
STEREO
BRIDG E MO NO
P U SH
P U SH
CAUTION
MODEL NO. MM9360
P U SH
115V
RISKOFELECTRICSHOCK
DONOTOPEN
50/60Hz 1400W
B R ID G E M O D E
S T E R E O M O DE
150W / C H A N - 8 OH M S
250W / C H A N - 4 OH M S
C H 1 (MONO)
CH 2
C H 3 (MONO)
CH 4
C H 5 (MONO)
CH 6
D C TR IG G ER
R C -5 R E M O T E
C O NT R OL
IN
OU T
CH2
CH3
CH4
CH5
CH6
+
IN
O UT PU TS
B R ID G E
B R ID G E
CH1
T AK E OU T PU T F RO M
T W O RE D PO ST S
D O N OT C ON NE C T EIT HE R
OU T PU T W IR E T O GR OU ND
B R ID G E M O D E
500W B RID GE - 8 OH M S
-
+
B R ID G E
-
+
-
OU T
R E PLA C E O N L Y W IT H
SA M E TY PE FUSE
R E FER TO O W N ER 'S M A N U A L
FO R PRO P ER FU SE RA T ING
AC
(+ )
(+ )
(+ )
(+ )
(+ )
CH 1
CH 2
CH 3
CH 4
CH 5
CH 6
(+ )
(-)
(-)
(-)
(-)
(-)
(-)
M A N U F A C T U R E D IN T H E U S A B Y A S H L Y A U D IO IN C O R P O R A T E D
To
Power
Outlet
Front
Surround
Center
-L-
-L-
Center
Out
Marantz
Remote
Control
L
R
Front
L
R
Surround
Cen
Sub
Center
Typical Surround Preamplifier Outputs
Typical Wiring Diagram
-
+
-
-
+
-
+
Sub
-R-
-R-
-
+
+
-
+
4. SPEAKER CONNECTIONS
6. CARE AND MAINTENANCE
This equipment, being a high audio output power ampli-
This section describes the car and maintenance tasks that
fier, has a hazardous energy at its speaker terminal. Please
be sure to make an appropriate speaker connection according to the following procedure:
must be performed to optimize the operation of your
marantz equipment.
- Confirm that the power switch of the equipment is at "OFF"
position. If it is at "ON", turn it to "OFF" position to connect a speaker cable.
- Use a speaker cable with the flame retardant rating of
type SPT12 or more.
- For bare wire connections, strip the insulation off no more
than 3/8" at the speaker terminal connection of speaker
cable, and twist the exposed wire. For banana-type plugs
or spade terminals, follow the instructions of the connector manufacturer.
- Connect speakers in correct polarity, according to the
indication for the polarity of speaker terminals. For bare
wire or spade terminal connections, first loosen the speaker
CLEANING OF EQUIPMENT EXTERNAL SURFACES
The exterior finish of your unit will last indefinitely with
proper care and cleaning. Never use scouring pads, steel
wool, scouring powders or harsh chemical agents (e.g. lye
solution), alcohol, thinners, benzine insecticide or other
volatile substances as these will mar the finish of the equipment.
Likewise, never use cloths containing chemical substances.
If the equipment gets dirty, wipe the external surface with
a soft, lint free cloth.
If the equipment becomes heavily soiled:
- Dilute some washing up liquid in water, in a ratio of one
part detergent to six parts water.
terminal by turning in a counter-clockwise direction, insert
the bare wire or spade terminal, then re-tighten by turning
the terminal clockwise.
- Dip a soft, lint free cloth in the solution and wring the
cloth out until it is damp.
- Prevent any stress from being applied to the speaker cable
- Dry the equipment by wiping it with a dry cloth.
- Wipe the equipment with the damp cloth.
connected to the speaker terminal.
- Don't touch the speaker terminals during operation.
7