Download Distributed I/O 2006

Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Distributed I/O
Overview
338
CC-Link Overview
339
CC-Link Remote I/O
343
CC-Link Analog Modules
376
CC-Link Special Function I/O
388
Profibus-DP I/O Modules
398
Profibus-DP I/O Analog Modules
402
CC-Link/LT Overview
404
CC-Link/LT Screw Terminal Modules
406
CC-Link/LT Spring Clamp Modules
408
CC-Link/LT e-CON Modules
409
CC-Link/LT MIL Connector Modules
411
CC-Link/LT Cable Type Modules
412
CC-Link/LT Accessories
415
I/O Link Modules
416
Dimensional Drawings
417
Mitsubishi Electric Automation
|
Distributed I/O 337
Control Level:
MELSECNET/H, NET/10, NET/II, NET/B
These Mitsubishi Electric control level networks allow controller to controller networking, plus the ability to place regular rack
based I/O on a network link that operates up to 25Mbit/s. A network node of remote I/O uses a standard controller base with a
remote I/O network adapter in place of a CPU. As a standard base unit is used, any type of regular rack based I/O or special
function module may be used. This gives tremendous flexibility for configuring remote I/O nodes. For more details on modules
available, please refer to the relevant Q, QnA, AnS or A Series controller sections. Note that in general, a remote I/O network is a
separate network segment to a controller network.
Device Level:
CC-Link
CC-Link is a high performance, open device level network that operates up to 10Mbit/s. Mitsubishi Electric offers extensive
support for this network, with a wide variety of I/O and special function modules that sit directly on the network, under the control
of a Q, QnA, AnS/QnAS, A or FX2N Supermicro Series controller. This section presents the I/O and special function modules
available, divided into device types. For information on other Mitsubishi Electric automation products that support CC-Link, please
refer to the other controller, HMI, VFD and Servo sections of this publication.
Profibus-DP
Profibus-DP is an alternative open device level network also widely supported by Mitsubishi Electric . This section presents the
I/O choices available. For information on other Mitsubishi Electric automation products that support Profibus, please refer to the
other controller, HMI & VFD sections of this publication.
Sensor Level:
CC-Link/LT
CC-Link/LT is a sensor level version of CC-Link. It offers a way to simply connect discrete I/O to a controller with a minimum of
installation and labor costs. CC-Link/LT uses a special “vampire” style connection technology to make device connections with no
cutting or stripping of cable.
I/O Link
I/O link is a standalone Mitsubishi Electric network that handles small quantities of digital I/O on a twisted pair connection. I/O
Link is easy to program and install and is supported by most of our controllers.
338
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
In addition to our controllers, Mitsubishi Electric can offer you the capability to add a broad range of I/O to
allow you to place I/O points close to where they are required on your machine or line. We offer three
main approaches to putting I/O on a network:
Q Series
Controller
A/QnA Series Controller
A500
AC Drives
FX2N Supermicro Controller
GOT HMI
3rd Party Devices
D75 Dual Axis
Motion
Controller
e
Third Party Devices:
Sensors, Valves, Etc.
MR-J2/Motor
Servo Amp
el
Laptop PC
Remote Modules:
I/O, Analog, HighSpeed Controllers,
RTD, Etc.
De
vic
Remote Program
Interface
Lev
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Supervisory
PC
AnSH/QnASH
Series Controller
Solution
CC-Link
Control and Communication Link (CC-Link) is an open network administered as a fully open architecture by the CC-Link
Partner Association (CLPA). Currently over 300 vendors are manufacturing products for it.
CC-Link was designed from the outset as a “flat” network. This means it offers both high speed response of I/O performance, but also high volumes of data communication as required in more complex distributed systems. CC-Link guarantees
a full 10Mbit/s performance across the whole network, regardless of device type, eliminating hidden bottle necks, common
with other open systems. While configuration software is not mandatory, CC-Link Configurator offers an intuitive, graphical
network configuration tool for setting up and troubleshooting a system. Our standard GX Developer development suite also
includes built-in configuration tools for CC-Link.
CC-Link offers you the widest choices for integrating a wide variety of automation components into a single, seamless
automation system. We can offer a system that can include any of the following items on the network:
p
p
p
p
p
p
p
p
p
Master or local controllers (Q, QnA, QnASH, AnSH, A, FX)
GOT HMI
E and A500 VFD
Discrete I/O (in a wide variety of types and configurations)
Analog I/O
High speed counters
Motion control
RTD/Thermocouple modules
PC stations via PC-link cards
Mitsubishi Electric Automation
|
Distributed I/O 339
This section presents the current line-up of CC-Link I/O blocks and special function modules. For network master modules, please refer to the
appropriate controller section. Before using this guide, please read the following guide to nomenclature:
Guide to CC-Link I/O Nomenclature
Generic part number format
Note on “1-wire”, “2-wire”, “3-wire” & “4-wire” terminology
Throughout the CC-Link blocks, we reference these terms. These are concise definitions for the following ways to connect I/O devices:
• 1 wire: One side of the load is connected to the I/O module terminal block. The other side is connected to a common terminal shared by
all devices.
• 2 wire: One side of the load is connected to the I/O module terminal block. The other side is connected to a dedicated common terminal
for that load on the terminal block. Note that in some cases, the common terminals may be connected internally.
• 3 wire: The I/O block is configured to accept loads with three connections (such as various types of sensor, etc)
• 4 wire: As three wire, but configured for four connection devices.
Note on connector types
Various different types of connector styles are available on the CC-Link blocks, as follows:
NOTE: IN GENERAL, BLOCKS ARE NOT SUPPLIED WITH CONNECTORS AND ACCESSORIES (IF REQUIRED). PLEASE INSURE
YOU HAVE ALL NECESSARY CONNECTORS BEFORE BEGINNING AN INSTALLATION.
• Screw terminals: These are conventional screw terminals. Note that all wiring will require cutting, stripping, and terminating with a
crimped spade or ring type lug to insure a reliable connection.
• FCN connector: These are 40 pin connectors that allow fast connection and disconnection of a whole group of I/O in one action.
The following types of FCN connector are available:
Model Number
A6CON1
A6CON2
A6CON3
340
Certification
UL • cUL
UL • cUL
UL • cUL
Number of Pins
40
40
40
Wiring Type
Solder
Crimp
IDC
Connector Type
FCN
FCN
FCN
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Guide to CC-Link I/O and Special Function Modules
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
One Touch Connector (OTC): OTC offer significant installation and maintenance benefits as follows:
• IDC (insulation displacement connector) type connection avoids need for stripping or terminating wiring with lugs. Simply cut wiring
to length, insert into connector and snap shut to make a reliable connection. These are available for I/O, network & power connections.
• Easily connected and disconnected individually or in groups to assist maintenance
• Compact design minimizes I/O block size
• Available in a variety of wiring gauge sizes and colors for identification
• Shipped in boxes of 20 connectors; divide quantity required by 20, then round up to next whole number for correct order quantity.
Model Number
Gauge Size (AWG)
Color
Qty. Per Box
Comments
A6CON-P214
26-24
Transparent
20
For I/O
A6CON-P220
26-24
Yellow
20
For I/O
A6CON-P514
22-20
Red
20
For I/O
A6CON-P520
22-20
Blue
20
For I/O
• Waterproof M12 connectors: Selected I/O blocks are available in an IP67 waterproof format. These use connectors that use a M12
metric threaded connector to make all connections. Benefits include:
• Water tight connections for installations where exposure to liquids is required
• In some installations, these blocks may be mounted directly on a machine without the need for an enclosure, reducing system cost.
• Miscellaneous accessories: The following accessories are also available: Note the quantity per box and calculate the correct order
quantity accordingly.
Model Number
Quantity Per Box
BA1SJ61-S
N/A
Comments
Three conductor, CLPA certified, signal only CC-Link cable. Sold by the meter.
BA1SJ61-P
N/A
Five conductor, CLPA certified, signal and power CC-Link cable. Sold by the meter.
A6CON-L5P
10
OTC network connector
A6CON-PW5P
10
OTC network connector
A6CON-LJ5P
5
OTC Network on-line connector (1)
A6CON-PWJ5P
5
OTC Power on-line connector (2)
A6CON-TR11
1
Terminating resistor (3)
A6CAP-DC1
20
Dust cap to protect unused connectors on IP67 modules (4)
A6CAP-WP1
20
Metal waterproof cap to protect unused connectors on IP67 modules (4)
A6CAP-WP2
20
Plastic waterproof cap to protect unused connectors on IP67 modules (4)
A6PLT-J65V1
1
DIN rail mount for vertical format blocks (single width)
A6PLT-J65V2
1
DIN rail mount for vertical format blocks (double width)
BKO-C8834H12
2 x 110 ohm, 2 x 130 ohm
BKO-C10798H02
1
CC-Link terminating resistors with insulating lugs
QJ61BT11 network terminal block assembly
Notes:
1. This connector accepts two A6CON-L5P and plugs into a CC-Link module. Its function is to allow a network connection to be connected/disconnected via a single operation,
and maintains the network connection. Note these are only used with "VBT" type modules.
2. Accepts two A6CON-PW5P and performs the same function as A6CON-LJ5P for power. Use only with "VBT" modules.
3. Required at the end of a network segment for reliable communication for "VBT" modules.
4. AJ65FBT & AJ65SBTW4 type modules
Mitsubishi Electric Automation
|
Distributed I/O 341
Model Number
Description
Contents
Included?
SH(NA)4007
CC-Link System Compact Type Remote I/O Module
Covers all CC-Link digital I/O blocks
No (purchase separately)
SH(NA)3614
AJ65BT-64AD Analog Digital Converter Module User’s Manual
Covers AJ65BT-64AD
No (purchase separately)
IB(NA)66748
AJ65BT-64AD Analog Digital Converter Module User’s Manual
(Hardware)
Covers basic features of the AJ65BT-64AD
Yes
SH(NA)3615
AJ65BT-64DAV/DAI Digital Analog Conversion Module User’s Manual
Covers AJ65BT-64DAV & 64DAI
No (purchase separately)
SH(NA)080107
AJ65SBT-62DA Digital-Analog Converter Module User’s Manual
Covers AJ65SBT-62DA
No (purchase separately)
IB(NA)0800139
AJ65SBT-62DA Digital-Analog Converter Module User’s Manual
(Hardware)
Covers basic features of the AJ65BT-62DA
Yes
SH(NA)080106
AJ65SBT-64AD Analog-Digital Converter Module User’s Manual
Covers AJ65SBT-64AD
No (purchase separately)
Covers basic features of the AJ65SBT-64AD
Yes
Covers AJ65VBTCU-68ADV & 68ADI
No (purchase separately)
Covers basic features of the
AJ65VBTCU-68ADV & 68ADI
Yes
AJ65VBTCU-68DAV Digital-Analog Converter Module User’s Manual
Covers AJ65VBTCU-68DAV
No (purchase separately)
AJ65VBTCU-68DAV Digital-Analog Converter Module User’s Manual
(Hardware)
AJ65BT-64RD3/-64RD4 Pt100 Temperature Input Module User’s
Manual
AJ65BT-64RD3/-64RD4 Pt100 Temperature Input Module User’s
Manual (Hardware)
Covers basic features of the
AJ65VBTCU-68DAV
Yes
Covers AJ65BT-64RD3/-64RD4
No (purchase separately)
Covers basic features of the AJ65BT-64RD3
& 64RD4
Yes
AJ65BT-68TD Thermocouple Input Module User’s Manual (Hardware)
Covers AJ65BT-68TD
Yes
AJ65BT-D62/D62D/D62D-S1 High Speed Counter Module User’s
Manual
AJ65BT-D62/D62D/D62D-S1 High Speed Counter Module User’s
Manual (Hardware)
Covers all CC-Link high speed counter
modules
Covers basic features of high speed counter
modules
IB(NA)66824
AJ65BT-D75P2-S3 Positioning Module User’s Manual
Covers AJ65BT-D75P2-S3
IB(NA)66829
AJ65BT-D75P2-S3 Positioning Module User’s Manual (Hardware)
Covers basic features of the AJ65BT-D75P2-S3 Yes
IB(NA)66781
AJ65BT-R2 RS232 Interface Module User’s Manual
Covers AJ65BT-R2
No (purchase separately)
IB(NA)66780
AJ65BT-R2 RS232 Interface Module User’s Manual (Hardware)
Covers basic features of the AJ65BT-R2
Yes
SH(NA)080105
AJ65BT-G4-S3 Peripheral Connection Module User’s Manual
Covers AJ65BT-G4-S3
No (purchase separately)
IB(NA)0800137
AJ65BT-G4-S3 Peripheral Connection Module User’s Manual
(Hardware)
Covers basic features of the AJ65BT-G4-S3
Yes
IB(NA)0800251
Analog-Digital Converter Module User’s Manual (Hardware)
AJ65VBTCU-68ADVN/ADIN
Covers basic features of the AJ65VBTCU68ADVN/ADIN
Yes
SH(NA)080401
Analog-Digital Converter Module Type AJ65VBTCU-68ADVN/ADIN
User’s Manual
Covers AJ65VBTCU-68ADVN and
AJ65VBTCU-68ADIN
No (purchase separately)
IB(NA)8000252
Digital-Analog Converter Module User’s Manual (Hardware)
AJ65VBTCU-68DAVN
Covers basic features of the AJ65VBTCU68DAVN
Yes
SH(NA)080402
Digital-Analog Converter Module Type AJ65VBTCU-68DAVN User’s
Manual
Covers AJ65VBTCU-68DAVN
No (purchase separately)
IB(NA)0800240
AJ65SBT-CLB CC-Link-CC-Link/LT Bridge Module User’s Manual
(Hardware)
Contains basic information on the bridge
module
Yes
SH(NA)080362
AJ65SBT-CLB CC-Link-CC-Link/LT Bridge Module User’s Manual
Covers the bridge module
No (purchase separately)
IB(NA)0800138
SH(NA)080181
IB(NA)0800200
SH(NA)080182
IB(NA)0800201
SH(NA)4001
IB(NA)66831
IB(NA)66830
IB(NA)66823
IB(NA)66822
AJ65SBT-64AD Analog-Digital Converter Module User’s Manual
(Hardware)
AJ65VBTCU-68ADV/ADI Analog-Digital Converter Module User’s
Manual
AJ65VBTCU-68ADV/ADI Analog-Digital Converter Module User’s
Manual (Hardware)
Note: Many of these manuals are available by free download from our website, www.meau.com
342
No (purchase separately)
Yes
No (purchase separately)
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Required Manuals
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CC-Link Remote I/O: AJ65SBTBo-o• AJ65BTBo-o
Screw Terminal Block Type
AJ65SBTBo-o/AJ65BTBo-o
• Screw Terminals
n Widest range of I/O types in CC-Link I/O product line.
n AJ65BTBo-o types equipped with removable terminal blocks.
n AJ65SBTBo-o offer most efficient use of panel space.
n All models UL • cUL listed and CE certified.
Finger protector
Sprung screw
retracts to insert
wiring lug
Terminal block
Performance Specifications
Operating Voltage
ON Voltage
OFF Voltage
AJ65SBTB1-8D
DC input
+COM/–COM common type
8 points
Photocoupler
24 VDC
14 V min.
6 V max.
Input Response Time
OFF—ON
ON—OFF
1.5 ms max.
1.5 ms max.
One wire type
8 points 1 common
30mA
AJ65SBTB1-16D
DC input
+COM/–COM common type
16 points
Photocoupler
24 VDC
14 V min.
6 V max.
1.5 ms max.
1.5 ms max.
One wire type
16 points 1 common
35mA
AJ65SBTB1-16D1
DC input
+COM/–COM common type
16 points
Photocoupler
24 VDC
15 V min.
3 V max.
0.2 ms max.
0.2 ms max.
One wire type
16 points 1 common
40mA
AJ65SBTB1-32D
DC input
+COM/–COM common type
32 points
Photocoupler
24 VDC
14 V min.
6 V max.
1.5 ms max.
1.5 ms max.
One wire type
32 points 1 common
45mA
AJ65SBTB1-32D1
DC input
+COM/–COM common type
32 points
Photocoupler
24 VDC
15 V min.
3 V max.
0.2 ms max.
0.2 ms max.
One wire type
32 points 1 common
50mA
AJ65SBTB2N-8A
AC input
—
8 points
Photocoupler
100 to 120 VAC
80 V min.
30 V max.
20 ms max.
20 ms max.
Two wire type
8 points 1 common
35mA
AJ65SBTB2N-16A
AC input
—
16 points
Photocoupler
100 to 120 VAC
80 V min.
30 V max.
20 ms max.
20 ms max.
Two wire type
16 points 1 common
40mA
AJ65SBTB3-8D
DC input
+COM/–COM common type
8 points
Photocoupler
24 VDC
14 V min.
6 V max.
1.5 ms max.
1.5 ms max.
Three wire type
8 points 1 common
40mA
AJ65SBTB3-16D
DC input
+COM/–COM common type
16 points
Photocoupler
24 VDC
14 V min.
6 V max.
1.5 ms max.
1.5 ms max.
Three wire type
16 points 1 common
45mA
AJ65BTB1-16D
DC input
+COM/–COM common type
16 points
Photocoupler
24 VDC
14 V min.
6 V max.
10 ms max.
10 ms max.
One wire type
16 points 1 common
60mA
AJ65BTB2-16D
DC input
+COM/–COM common type
16 points
Photocoupler
24 VDC
14 V min.
6 V max.
10 ms max.
10 ms max.
Two wire type
16 points 1 common
Input Module
Model Name
Output Module
Model Name
Input Type
Number of
Input Points
Isolation
Method
Rated Input
Voltage
Number of
Output Points
Isolation
Method
Rated load
Voltage
Maximum Load Current
Output Response Time
External Connection
Internal Current
Common Connection
Wire Type
Consumption
60mA
Surge
Suppression
External
Connection
Wire Type
Common
Connection
Internal
Current
Consumption
1 Point
1 Common
OFF—ON
ON—OFF
Leakage
Current
AJ65SBTB1-8T
Transistor output
Sink type
8 points
Photocoupler
12/24 VDC
0.5A
2.4A
0.5 ms max.
1.5 ms max.
0.25 mA max.
Zener diode
One wire type
8 pts 1 com
35mA
AJ65SBTB1-8T1
Transistor output
Sink type
8 points
Photocoupler
12/24 VDC
0.5A
2.4A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
One wire type
8 pts 1 com
35mA
AJ65SBTB1-16T
Transistor output
Sink type
16 points
Photocoupler
12/24 VDC
0.5A
3.6A
0.5 ms max.
1.5 ms max.
0.25 mA max.
Zener diode
One wire type
16 pts 1 com
50mA
AJ65SBTB1-32T
Transistor output
Sink type
32 points
Photocoupler
12/24 VDC
0.5A
4.8A
0.5 ms max.
1.5 ms max.
0.25 mA max.
Zener diode
One wire type
32 pts 1 com
65mA
AJ65SBTB1-16T1
Transistor output
Sink type
16 points
Photocoupler
12/24 VDC
0.5A
3.6A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
One wire type
16 pts 1 com
50mA
AJ65SBTB1-32T1
Transistor output
Sink type
32 points
Photocoupler
12/24 VDC
0.5A
4.8A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
One wire type
32 pts 1 com
65mA
AJ65SBTB1-8TE
Transistor output
Source type
8 points
Photocoupler
12/24 VDC
0.1A
0.8A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
One wire type
8 pts 1 com
35mA
AJ65SBTB1-16TE
Transistor output
Source type
16 points
Photocoupler
12/24 VDC
0.1A
1.6A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
One wire type
16 pts 1 com
50mA
AJ65SBTB2-8T
Transistor output
Sink type
8 points
Photocoupler
12/24 VDC
0.5A
2.4A
0.5 ms max.
1.5 ms max.
0.25 mA max.
Zener diode
Two wire type
8 pts 1 com
45mA
AJ65SBTB2-16T
Transistor output
Sink type
16 points
Photocoupler
12/24 VDC
0.5A
3.6A
0.5 ms max.
1.5 ms max.
0.25 mA max.
Zener diode
Two wire type
16 pts 1 com
55mA
AJ65SBTB2-8T1
Transistor output
Sink type
8 points
Photocoupler
12/24 VDC
0.5A
2.4A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
Two wire type
8 pts 1 com
45mA
AJ65SBTB2-16T1
Transistor output
Sink type
16 points
Photocoupler
12/24 VDC
0.5A
3.6A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
Two wire type
16 pts 1 com
55mA
AJ65SBTB2N-8R
Relay output
—
8 points
Relay
24 VDC/240 VAC
2A
4A
10 ms max.
12 ms max.
—
None
Two wire type
8 pts 1 com
85mA
AJ65SBTB2N-16R
Relay output
—
16 points
Relay
24 VDC/240 VAC
2A
8A
10 ms max.
12 ms max.
—
None
Two wire type
16 pts 1 com
120mA
AJ65SBTB2N-8S
Triac output
—
8 points
Photocoupler
100 to 240 VAC
0.6A
2.4A
1 ms max.
1/2c + 1 ms max.
—
C-R absorber
Two wire type
8 pts 1 com
55mA
AJ65SBTB2N-16S
Triac output
—
16 points
Photocoupler
100 to 240 VAC
0.6A
4.8A
1 ms max.
1/2c + 1 ms max.
—
C-R absorber
Two wire type
16 pts 1 com
85mA
AJ65BTB1-16T
Transistor output
Sink type
16 points
Photocoupler
12/24 VDC
0.5A
4A
2 ms max.
2 ms max.
0.1 mA max.
Zener diode
One wire type
8 pts 1 com
80mA
AJ65BTB2-16R
Relay output
—
16 points
Relay
24 VDC/240 VAC
2A
8A
10 ms max.
12 ms max.
—
None
Two wire type
8 points 1 com
85mA
AJ65BTB2-16T
Transistor output
Sink type
Output Type
Combined I/O
Module Model
Name
I/O Type
DC input
/trans output
DC input
AJ65SBTB1-16DT1 /trans output
DC input
AJ65SBTB1-16DT2 /trans output
DC input
AJ65SBTB1-16DT3 /trans output
DC input
AJ65SBTB1-32DT /trans output
DC input
AJ65SBTB1-32DT1 /trans output
DC input
AJ65SBTB1-32DT2 /trans output
DC input
AJ65SBTB1-32DT3 /trans output
DC input
AJ65SBTB32-8DT /trans output
DC input
AJ65SBTB32-8DT2 /trans output
DC input
AJ65SBTB32-16DT /trans output
DC input
AJ65SBTB32-16DT2 /trans output
DC input
AJ65BTB1-16DT
/trans output
DC input
AJ65BTB2-16DT
/trans output
AJ65SBTB1-16DT
AJ65BTB2-16DR
DC input
/relay output
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM type/sink type
+COM/–COM
common type/–
4A
0.5A
2 ms max.
2 ms max.
0.1 mA max.
12/24 VDC
16 points
Photocoupler
Number Isolation
Input
Maximum Load Current
Operating Voltage Output Response Time
Input/Load
of I/O
Response
Method
Voltage
1 Point
1 Common ON Voltage OFF Voltage OFF—ON
Points
Time
ON—OFF
8 pts
/8 pts
8 pts
/8 pts
8 pts
/8 pts
8 pts
/8 pts
16 pts
/16 pts
16 pts
/16 pts
16 pts
/16 pts
16 pts
/16 pts
4 pts
/4 pts
4 pts
/4 pts
8 pts
/8 pts
8 pts
/8 pts
8 pts
/8 pts
8 pts
/8 pts
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
Photocoupler
/ photocoupler
8 pts
/8 pts
Photocoupler
/relay
Zener diode
Leakage
Current
Two wire type
80mA
8 pts 1 com
Connection
Internal
Surge
Common
Wire Type on
Current
Suppression Input/Output Sides Connection Consumption
24VDC/24VDC
1.5 ms max.
0.5A
2.4A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.25 mA max.
Zener diode
24VDC/24VDC
0.2 ms max.
0.5A
2.4A
15 V min.
3 V max.
0.5 ms max. 1.5 ms max.
0.25 mA max.
Zener diode
24VDC/24VDC
1.5 ms max.
0.5A
2.4A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.1 mA max.
Zener diode
24VDC/24VDC
0.2 ms max.
0.5A
2.4A
15 V min.
3 V max.
0.5 ms max. 1.5 ms max.
0.1 mA max.
Zener diode
24VDC/24VDC
1.5 ms max.
0.5A
3.6A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.25 mA max.
Zener diode
24VDC/24VDC
0.2 ms max.
0.5A
3.6A
15 V min.
3 V max.
0.5 ms max. 1.5 ms max.
0.25 mA max.
Zener diode
24VDC/24VDC
1.5 ms max.
0.5A
3.6A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.1 mA max.
Zener diode
24VDC/24VDC
0.2 ms max.
0.5A
3.6A
15 V min.
3 V max.
0.5 ms max. 1.5 ms max.
0.1 mA max.
Zener diode
24VDC/24VDC
1.5 ms max.
0.5A
1.2A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.25 mA max.
Zener diode
24VDC/24VDC
1.5 ms max.
0.5A
1.2A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.1 mA max.
Zener diode
24VDC/24VDC
1.5 ms max.
0.5A
2.4A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.25 mA max.
Zener diode
24VDC/24VDC
1.5 ms max.
0.5A
2.4A
14 V min.
6 V max.
0.5 ms max. 1.5 ms max.
0.1 mA max.
Zener diode
24VDC/12/24VDC
10 ms max.
0.5A
4A
14 V min.
6 V max.
2 ms max.
2 ms max.
0.1 mA max.
Zener diode
24VDC/12/24VDC
10 ms max.
0.5A
4A
14 V min.
6 V max.
2 ms max.
2 ms max.
0.1 mA max.
Zener diode
24VDC/240VAC
10 ms max.
2A
8A
14 V min.
6 V max.
10 ms max.
12 ms max.
—
None
One wire type
/ One wire type
One wire type
/ One wire type
One wire type
/ One wire type
One wire type
/ One wire type
One wire type
/ One wire type
One wire type
/ One wire type
One wire type
/ One wire type
One wire type
/ One wire type
Three wire type
/ Two wire type
Three wire type
/ Two wire type
Three wire type
/ Two wire type
Three wire type
/ Two wire type
One wire type
/ One wire type
Two wire type/
Two wire type
16 pts
1 com
16 pts
1 com
16 pts
1 com
16 pts
1 com
32 pts
1 com
32 pts
1 com
32 pts
1 com
32 pts
1 com
8 pts
1 com
8 pts
1 com
16 pts
1 com
16 pts
1 com
8 pts
1 com
8 pts
1 com
50mA
Two wire type/
Two wire type
8 pts
1 com
70mA
55mA
50mA
55mA
60mA
60mA
60mA
60mA
45mA
45mA
50mA
50mA
70mA
70mA
+COM: Positive common (sink) -COM: Negative common (source)
Mitsubishi Electric Automation
|
Distributed I/O 343
LED display
LED Name
Item Checked
X0 1 2 3 4 5 6 7
PW
Turns on when the power supply to the remote
I/O module is turned on.
L RUN
Turns on when normal data is received from the
master station, and turns off via timeout.
XO to 1F
Transmission speed
setting switch
B RATE
1 4 2 1
ON
Setting
value
Transmission
speed
0
156 kbps
AJ65SBTB1-8D
DA
L ERR
STATION NO.
40 20 10 8 4 2
DG
DB
Turns on in case of a transmission error
(CRC error) and turns off via timeout
(L RUN also turns off). It turns on if the settings
for station number and transmission speed are
wrong. (It turns off when the settings are modified and the power supply is turned off then on
again.) It flashes if the station-number and transmission-speed settings are changed while the
communication is active. (L RUN also turns on.
The module operates under the conditions
given via the station-number and transmissionspeed settings at the time the power supply was
turned on.)
+24V
24G
X0
X2
(FG)
SLD
X4
X1
X6
X3
COM
X5
X7
COM
625 kbps
2
2.5 Mbps
3
5.0 Mbps
4
10 Mbps
Station number
setting switches
"10," "20," and "40" in STATION NO. are used for
setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for
setting the first digit of the station number.
Displays the on/off status of input. The LEDs
turn on in the "On" state, and off in the "Off"
state.
DIN rail hook
Terminal block
Hook for mounting the module to the DIN rail
Unit: mm
External Dimensions
AJ65SBTB1-16o
AJ65SBTB3-8o
AJ65SBTB2-8o
AJ65SBTB2N-8o
AJ65SBTB32-8o
40
40
AJ65SBTB1-8o
87.3
118
78.3mm +10 (mounting pitch)
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
PW L RUN L ERR
X0
(FG)
SLD
X2
X4
X1
X6
X3
X5
DA
COM
X7
COM
DG
STATION NO.
B RATE
40 20 10 8 4 2 1 4 2 1
A J65SBTB1-16D
+24V
DB
50
24G
X8 9 A B C D E F
ON
MITSUBISHI
24G
SLD
X0
X2
(FG)
X1
X4
X3
X6
X5
X8
X7
XA
XC
X9
XB
XE
XD
COM
XF
COM
X16
X18
4
4
50
DB
+24V
X0 1 2 3 4 5 6 7
16.5
16.5
B RATE
4 2 1
ON
DG
(mounting pitch)
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
1
AJ65SBTB1-8D
DA
+1
0
109mm
STATION NO.
40 20 10 8 4 2
X0 1 2 3 4 5 6 7
AJ65SBTB1-32o
AJ65SBTB3-16o
AJ65SBTB2-16o
AJ65SBTB2N-16o
AJ65SBTB32-16o
46
40
9.5
AJ65BTB1-16o
179
Two ø4.5mm mounting holes
MITSUBISHI
A J65BTB1-16D
170mm +10 (mounting pitch)
Two 4.5mm x 5.1mm mounting holes (for M4 mounting screws)
B RATE
PW L RUN L ERR
L RUN
SD
RD
2
3
L ERR.
3
DA
+24V
4
DB
6
9
7
8
9
11
A
B
C
13
D
E
F
15
19
17
21
25
23
DB
50
5
DG
X10 11 12 13 14 15 16 17
X18 19 1A 1B 1C 1D 1E 1F
STATION NO.
B RATE
40 20 10 8 4 2 1 4 2 1
A J65SBTB1-32D
+24V
24G
SLD
X0
X2
(FG)
X1
X4
X3
X6
X5
X8
X7
XA
X9
XC
XB
XE
XD
X10
XF
X12
X11
X14
X13
X15
X17
X1A
X19
X1C
X1B
X1E
X1D
COM
X1F
COM
65
4
DA
56
3
7
5
DG
2
2
STATION NO.
X10
X1
0 1
9 0 1
2 8
2
3 7
3
6 5 4
6 5 4
27
24G
6
8
10
12
14
16
18
20
22
24
26
SLD
89
4
1
1
X8 9 A B C D E F
ON
MITSUBISHI
4
0
X0 1 2 3 4 5 6 7
16.5
0 1
PW
(FG)
142.9
151.9
Two ø4.5mm mounting holes
AJ65BTB2-16o
MITSUBISHI
A J65BTB2-16D
B RATE
0 1
PW
L RUN
SD
RD
2
3
L ERR.
46
1
3
DA
5
4
DB
2
3
7
+24V
DG
2
1
4
5
6
9
7
8
9
11
A
B
13
C
D
E
15
F
17
19
21
23
25
27
56
9.5
STATION NO.
X10
X1
0 1
9 0 1
2 8
2
3 7
3
6 5 4
6 5 4
29
31
33
35
37
24G
6
8
10
12
14
16
18
20
SLD
(FG)
188.4
197.4
22
24
26
28
30
32
34
36
65
4
0
344
1
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Guide to Module Features
External Connections
Input Modules
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
AJ65SBTB1-8D type
Module power
supply
I/O power
supply
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
X0
X1
X2
X3
X4
X5
X6
X7
COM
COM
AJ65SBTB1-16D type, AJ65SBTB1-16D1 type
Isolation
DC/DC
Module power
supply
R
R
R
R
I/O power
supply
AJ65SBTB1-32D type • AJ65SBTB1-32D1 type
Module power
supply
I/O power
supply
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
X0
X1
X2
X3
X4
X5
X6
X7
X8
X9
XA
XB
XC
XD
XE
XF
X10
X11
X12
X13
X14
X15
X16
X17
X18
X19
X1A
X1B
X1C
X1D
X1E
X1F
COM
COM
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
X0
X1
X2
X3
X4
X5
X6
X7
X8
X9
XA
XB
XC
XD
XE
XF
COM
COM
Isolation
DC/DC
R
R
R
R
AJ65SBTB2N-8A type
1
Isolation
DC/DC
R
R
Module power
supply
DA
2
DB
3
DG
4
SLD
5
+24V
6
FG
7
24G
8
X0
Isolation
DC/DC
R
R
9 COM B
R
10 X1
11 COM B
12 X2
13 COM B
14 X3
15 COM B
16 X4
17 COM B
18 X5
19 COM B
20 X6
21 COM B
22 X7
23 COM B
24 COM A
R
25 COM B
R
AC100V
AJ65SBTB2N-16A type
AJ65SBTB3-8D type
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
X0
COM B
X1
COM B
X2
COM B
X3
COM B
X4
COM B
X5
COM B
X6
COM B
X7
COM B
X8
COM B
X9
COM B
XA
COM B
XB
COM B
XC
COM B
XD
COM B
XE
COM B
XF
COM B
COM A
COM B
1
2
3
4
5
6
7
Isolation
DC/DC
Module power
supply
DA
DB
DG
SLD
+24V
FG
24G
Isolation
DC/DC
Module power supply
R
R
R
Three wire
type sensor
Two wire
type sensor
Source
Sink
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
X0
COMA
X1
COMB
X2
COMA
X3
COMB
X4
COMA
X5
COMB
X6
COMA
X7
COMB
DC24A
DC24B
R
R
DC24V
AC100V
Mitsubishi Electric Automation
|
Distributed I/O 345
AJ65SBTB3-16D type
AJ65BTB1-16D type
Module
power supply
Three wire
type sensor
Two wire
type sensor
Source
Sink
DC24V
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
X0
COMA
X1
COMB
X2
COMA
X3
COMB
X4
COMA
X5
COMB
X6
COMA
X7
COMB
X8
COMA
X9
COMB
XA
COMA
XB
COMB
XC
COMA
XD
COMB
XE
COMA
XF
COMB
DC24A
DC24B
Isolation
DC/DC
R
DC24V
R
DC24V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
DA
DB
DG
SLD
+24V
FG
24G
X0
X1
X2
X3
X4
X5
X6
X7
COM
NC
X8
X9
XA
XB
XC
XD
XE
XF
COM
NC
DC/DC
R
R
R
R
AJ65BTB2-16D type
DC24V
DC24V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Output Modules
DA
DB
DG
SLD
+24V
FG
24G
NC
NC
X0
COMB
X1
X2
COMB
X3
X4
COMB
X5
X6
COMB
X7
NC
NC
X8
COMB
X9
XA
COMB
XB
XC
COMB
XD
XE
COMB
XF
COMA
COMB
AJ65SBTB1-8T type
DC/DC
R
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
CTL+
COM-
Isolation
DC/DC
Module power
supply
R
Constant
voltage circuit
L
I/O power supply
(external power supply)
L
Load power supply
In case I/O power supply and
load power supply are common
R
R
L
L
8
9
10
11
12
13
14
15
16
17
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
CTL+
COM-
AJ65SBTB1-16T type
AJ65SBTB1-8T1 type
Module power
supply
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
CTL+
COM-
Module power
supply
L
I/O power supply
(external power supply)
L
Load power supply
In case I/O power supply and
load power supply are common
L
L
346
8
9
10
11
12
13
14
15
16
17
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
CTL+
COM-
L
Isolation
DC/DC
Constant
voltage circuit
L
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
YA
YB
YC
YD
YE
YF
CTL+
COM-
I/O power supply
(external power supply)
Load power supply
L
24 CTL+
25 COM-
Isolation
DC/DC
Constant
voltage
circuit
In case I/O power supply
and load power supply are common
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
External Connections
External Connections
AJ65SBTB1-32T type
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
AJ65SBTB1-16T1 type
Module power
supply
L
L
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
YA
YB
YC
YD
YE
YF
CTL+
COM-
I/O power supply
(external power supply)
Load power supply
Isolation
Module power
supply
DC/DC
L
Constant
voltage
circuit
In case I/O power supply
and load power supply are common
L
24 CTL+
25 COM-
L
I/O power supply
(external power supply)
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
YA
YB
YC
YD
YE
YF
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y1A
Y1B
Y1C
Y1D
Y1E
Y1F
CTL+
COM-
Isolation
DC/DC
Constant
voltage
circuit
Load power supply
L
40 CTL+
41 COM-
In case I/O power supply
and load power supply are common
AJ65SBTB1-32T1 type
Module power
supply
L
L
I/O power supply
(external power supply)
Load power supply
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
YA
YB
YC
YD
YE
YF
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y1A
Y1B
Y1C
Y1D
Y1E
Y1F
CTL+
COM-
L
40 CTL+
41 COM-
Isolation
DC/DC
AJ65SBTB1-8TE type
Module power
supply
Load power
supply
Module power
supply
L
L
Load power
supply
I/O power supply
(external power supply)
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
YA
YB
YC
YD
YE
YF
COM+
CTL-
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
COM+
CTL-
Isolation
DC/DC
Constant
voltage circuit
L
In case I/O power supply
and load power supply are common
16 COM+
17 CTLConstant
voltage
circuit
In case I/O power supply
and load power supply are common
AJ65SBTB2-8T type
Isolation
DC/DC
Module power
supply
L
Constant
voltage circuit
In case I/O power supply
and load power supply are common
L
L
I/O power supply
(external power supply)
AJ65SBTB1-16TE type
1
2
3
4
5
6
7
L
1
2
3
4
5
6
7
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Y0
COM
Y1
COM
Y2
COM
Y3
COM
Y4
COM
Y5
COM
Y6
COM
Y7
COM
DC24V
DC24G
Isolation
DC/DC
Constant
voltage
circuit
I/O power supply
(external power supply)
24 COM+
25 CTL-
Mitsubishi Electric Automation
|
Distributed I/O 347
n DISTRIBUTED I/O
External Connections
AJ65SBTB2-16T type
AJ65SBTB2-8T1 type
L
I/O power supply
(external power supply)
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Y0
COM
Y1
COM
Y2
COM
Y3
COM
Y4
COM
Y5
COM
Y6
COM
Y7
COM
DC24V
DC24G
Isolation
L
DC/DC
Constant
voltage circuit
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Y0
COM
Y1
COM
Y2
COM
Y3
COM
Y4
COM
Y5
COM
Y6
COM
Y7
COM
Y8
COM
Y9
COM
YA
COM
YB
COM
YC
COM
YD
COM
YE
COM
YF
COM
DC24V
DC24G
Isolation
DC/DC
Constant
voltage circuit
I/O power supply
(external power supply)
AJ65SBTB2-16T1 type
Module power
supply
L
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Y0
COM
Y1
COM
Y2
COM
Y3
COM
Y4
COM
Y5
COM
Y6
COM
Y7
COM
Y8
COM
Y9
COM
YA
COM
YB
COM
YC
COM
YD
COM
YE
COM
YF
COM
DC24V
DC24G
Isolation
AJ65SBTB2N-8R type
DC/DC
1
Module
power supply
L
DA
2
DB
3
DG
4
SLD
5
+24V
6
FG
7
24G
8
Y0
Isolation
DC/DC
9 COM B
RA
10 Y1
11 COM B
12 Y2
13 COM B
14 Y3
15 COM B
16 Y4
17 COM B
18 Y5
19 COM B
20 Y6
21 COM B
Constant
voltage circuit
L
22 Y7
23 COM B
I/O power supply
(external power supply)
24 COM A
25 COM B
AC100/200V
AJ65SBTB2N-8S type
AJ65SBTB2N-16S type
AJ65SBTB2N-16R type
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
Isolation
DC/DC
Module power supply
L
L
AC100/200V
348
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Y0
COM B
Y1
COM B
Y2
COM B
Y3
COM B
Y4
COM B
Y5
COM B
Y6
COM B
Y7
COM B
Y8
COM B
Y9
COM B
YA
COM B
YB
COM B
YC
COM B
YD
COM B
YE
COM B
YF
COM B
COM A
COM B
1
DA
2
DB
3
DG
4
SLD
5
+24V
6
FG
7
24G
Module
power supply
Module
power supply
DC/DC
L
Surge suppression
RA
L
Isolation
8
Y0
9 COM B
10 Y1
11 COM B
R
Triac
12 Y2
13 COM B
14 Y3
15 COM B
16 Y4
17 COM B
18 Y5
19 COM B
20 Y6
21 COM B
L
22 Y7
23 COM B
L
24 COM A
25 COM B
AC100/200V
AC100/200V
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Y0
COM B
Y1
COM B
Y2
COM B
Y3
COM B
Y4
COM B
Y5
COM B
Y6
COM B
Y7
COM B
Y8
COM B
Y9
COM B
YA
COM B
YB
COM B
YC
COM B
YD
COM B
YE
COM B
YF
COM B
COM A
COM B
Isolation
DC/DC
Surge suppression
R
Triac
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Module power
supply
1
2
3
4
5
6
7
Module power
supply
1
2
3
4
5
6
7
External Connections
AJ65BTB2-16T type
Output Modules
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
AJ65BTB1-16T type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
DC24V
L
DC12/24V
L
DC12/24V
DA
DB
DG
SLD
+24V
FG
24G
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
COM1+
CTL1Y8
Y9
YA
YB
YC
YD
YE
YF
COM2CTL2+
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DC24V
DC/DC
L
R
DC12/24V
R
L
DC12/24V
DA
DB
DG
SLD
+24V
FG
24G
NC
NC
Y0
COM1+
Y1
Y2
COM1+
Y3
Y4
COM1+
Y5
Y6
COM1+
Y7
COM1COM1+
Y8
COM2+
Y9
YA
COM2+
YB
YC
COM2+
YD
YE
COM2+
YF
COM2COM2+
DC/DC
R
R
R
R
Combination Input/Output Modules
AJ65BTB2-16R type
DC24V
DC24V
L
AC240V
L
AC240V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DA
DB
DG
SLD
+24V
FG
24G
CTLG
CTL+
Y0
COMB
Y1
Y2
COMB
Y3
Y4
COMB
Y5
Y6
COMB
Y7
COMA
COMB
Y8
COMD
Y9
YA
COMD
YB
YC
COMD
YD
YE
COMD
YF
COMC
COMD
AJ65SBTB1-16DT, AJ65SBTB1-16DT1 type
RA
L
RA
I/O power supply
(external power
supply)
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
24 COM+
25 COM-
R
R
Constant
voltage circuit
24 COM+
25 COM-
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
X0
X1
X2
X3
X4
X5
X6
X7
Y8
Y9
YA
YB
YC
YD
YE
YF
24
25
COM+
COM-
In case I/O power supply
and load power supply are common
AJ65SBTB1-32DT, AJ65SBTB1-32DT1 type
Isolation
Module
power supply
DC/DC
Load power supply
L
X0
X1
X2
X3
X4
X5
X6
X7
Y8
Y9
YA
YB
YC
YD
YE
YF
Isolation
DC/DC
Load power supply
AJ65SBTB1-16DT2, AJ65SBTB1-16DT3 type
I/O power supply
(external power
supply)
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Module power
supply
40 COM+
41 COM-
L
DA
DB
DG
SLD
+24V
FG
24G
DC/DC
L
Module
power supply
1
2
3
4
5
6
7
In case I/O power supply
and load power supply are common
R
R
L
Constant
voltage circuit
I/O power supply
(external power
supply)
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
X0
X1
X2
X3
X4
X5
X6
X7
X8
X9
XA
XB
XC
XD
XE
XF
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y1A
Y1B
Y1C
Y1D
Y1E
Y1F
COM+
COM-
Isolation
DC/DC
R
R
Constant
voltage circuit
Load power supply
In case I/O power supply
L
and load power supply are common
40 COM+
41 COM-
Mitsubishi Electric Automation
|
Distributed I/O 349
AJ65SBTB1-32DT2, AJ65SBTB1-32DT3 type
1
2
3
4
5
6
7
Module
power supply
DA
DB
DG
SLD
+24V
FG
24G
X0
8
9
X1
10
X2
11
X3
12
X4
13
X5
14
X6
15
X7
16
X8
17
X9
18
XA
19
XB
20
XC
21
XD
22
XE
23
XF
24 Y10
25 Y11
26 Y12
27 Y13
28 Y14
29 Y15
30 Y16
31 Y17
32 Y18
33 Y19
34 Y1A
35 Y1B
36 Y1C
37 Y1D
38 Y1E
39 Y1F
40 COM+
41 COM-
L
I/O power supply
(external power
supply)
AJ65SBTB32-8DT type
Isolation
DC/DC
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
X0
COM+
X1
COMX2
COM+
X3
COMY8
COM+
Y9
COM+
YA
COM+
YB
COM+
DC24V
DC24G
R
R
Module power
supply
Three wire
type sensor
L
Isolation
DC/DC
R
R
Constant
voltage circuit
I/O power supply
(external power supply)
Constant
voltage circuit
Load power supply
L
40 COM+
41 COM-
In case I/O power supply
and load power supply are common
AJ65SBTB32-16DT type
AJ65SBTB32-8DT2 type
Module power
supply
Three wire
type sensor
L
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
X0
COM+
X1
COMX2
COM+
X3
COMY8
COM+
Y9
COM+
YA
COM+
YB
COM+
DC24V
DC24G
Module
power supply
Isolation
DC/DC
Three wire
type sensor
R
R
L
Constant
voltage circuit
I/O power supply
(external power supply)
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
X0
COM+
X1
COMX2
COM+
X3
COMX4
COM+
X5
COMX6
COM+
X7
COMY8
COM+
Y9
COM+
YA
COM+
YB
COM+
YC
COM+
YD
COM+
YE
COM+
YF
COM+
DC24V
DC24G
Isolation
DC/DC
R
R
Constant
voltage circuit
I/O power supply
(external power supply)
AJ65SBTB32-16DT2 type
AJ65BTB1-16DT type
1
2
3
4
5
6
7
Module power
supply
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Three wire
type sensor
L
DA
DB
DG
SLD
+24V
FG
24G
X0
COM+
X1
COMX2
COM+
X3
COMX4
COM+
X5
COMX6
COM+
X7
COMY8
COM+
Y9
COM+
YA
COM+
YB
COM+
YC
COM+
YD
COM+
YE
COM+
YF
COM+
DC24V
DC24G
Isolation
DC/DC
R
R
DC24V
DC24V
L
DC12/24V
Constant
voltage circuit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
DA
DB
DG
SLD
+24V
FG
24G
X0
X1
X2
X3
X4
X5
X6
X7
COM1+
NC
Y8
Y9
YA
YB
YC
YD
YE
YF
COM2CTL2+
DC/DC
R
R
R
I/O power supply
(external power supply)
AJ65BTB2-16DT type
DC24V
DC24V
L
DC12/24V
350
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DA
DB
DG
SLD
+24V
FG
24G
NC
NC
X0
COM1X1
X2
COM1X3
X4
COM1X5
X6
COM1X7
COM1+
COM1Y8
COM2+
Y9
YA
COM2+
YB
YC
COM2+
YD
YE
COM2+
YF
COM2COM2+
AJ65BTB2-16DR type
DC24V
DC/DC
DC24V
R
R
DC24V
L
R
AC240V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DA
DB
DG
SLD
+24V
FG
24G
CTLG
CTL+
X0
COMB
X1
X2
COMB
X3
X4
COMB
X5
X6
COMB
X7
COMA
COMB
Y8
COMD
Y9
YA
COMD
YB
YC
COMD
YD
YE
COMD
YF
COMC
COMD
DC/DC
R
R
RA
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
External Connections
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CC-Link Remote I/O: AJ65SBTCo-o / AJ65VBTCUo-o
One-Touch Connector Type
n One touch connector offers labor and material cost savings;
No stripping of cable or lugs required.
n IDC type connection makes a reliable contact.
n Connectors available separately.
n All models UL • cUL listed and CE certified.
• One Touch Connectors
No need for soldering,
wire stripping
or screw tightening.
Press in
Wiring securely connected simply by pressing
the side of the plug inward after inserting the
wire into the connector.
Connector
For a detailed description of the connectors see introduction to this section.
Performance Specifications
Input Module
Model Name
Input Type
Number
of Input
Points
Isolation
Method
Rated
Input
Voltage
ON Voltage
OFF Voltage
OFF—ON
Common
Connection
ON—OFF
External
Connection
Wire Type
Input Response Time
Operating Voltage
Internal Current
Consumption
DC input
+COM/–COM
common type
32 points
Photocoupler
24 VDC
14 V min.
6 V max.
1.5 ms max.
1.5 ms max.
One wire type
32 pts 1 com
45mA
AJ65SBTC1-32D1
DC input
+COM/–COM
common type
32 points
Photocoupler
24 VDC
15 V min.
3 V max.
0.2 ms max.
0.2 ms max.
One wire type
32 pts 1 com
45mA
AJ65SBTC4-16D
DC input
+COM/–COM
common type
16 points
Photocoupler
24 VDC
14 V min.
6 V max.
1.5 ms max.
1.5 ms max.
Four wire type
16 pts 1 com
35mA
AJ65VBTCU3-8D1
DC input
+COM type
8 points
Photocoupler
24 VDC
15 V min.
3 V max.
0.2 ms max.
0.2 ms max.
Three wire type
8 pts 1 com
35mA
AJ65VBTCU3-16D1
DC input
+COM type
16 points
Photocoupler
24 VDC
15 V min.
3 V max.
0.2 ms max.
0.2 ms max.
Three wire type
16 pts 1 com
40mA
AJ65SBTC1-32D
Output Module
Model Name
Output Type
Number
of Output
Points
Isolation
Method
Rated
Load
Voltage
1 Point
1 Common
OFF—ON
ON—OFF
Leakage
Current
Max. Load Current
Output Response Time
External
Surge
Connection
Suppression
Wire Type
Common
Connection
Internal
Current
Consumption
AJ65SBTC1-32T
Transistor
output
Sink type
32 points
Photocoupler
12/24 VDC
0.1A
3.2A
0.5 ms max.
1.5 ms max.
0.25 mA max.
Zener diode
One wire type
32 points 1 common
60mA
AJ65SBTC1-32T1
Transistor
output
Sink type
32 points
Photocoupler
12/24 VDC
0.1A
3.2A
0.5 ms max.
1.5 ms max.
0.1 mA max.
Zener diode
One wire type
32 points 1 common
60mA
AJ65VBTCU2-8T
Transistor
output
Sink type
8 points
Photocoupler
12/24 VDC
0.1A
0.8A
1 ms max.
1 ms max.
0.1 mA max.
Zener diode
Two wire type
8 points 1 common
35mA
AJ65VBTCU2-16T
Transistor
output
Sink type
16 points
Photocoupler
12/24 VDC
0.1A
1.6A
1 ms max.
1 ms max.
0.1 mA max.
Zener diode
Two wire type
16 points 1 common
40mA
Combined I/O
Module
Model Name
I/O Type
Number
of I/O
Points
Isolation
Method
Rated
Input/Load
Voltage
24VDC/24VDC
Operating
Voltage
ON
Voltage
OFF
Voltage
1
1
Point Common
14 V min.
6 V max.
0.5A
DC input
/ trans output
+COM type
/ sink type
8 pts
/ 8 pts
Photocoupler
/ photocoupler
AJ65SBTC4-16DT2 DC input
/ trans output
+COM type
/ sink type
8 pts
/ 8 pts
Photocoupler
/ photocoupler
24VDC/24VDC
14 V min.
6 V max.
AJ65SBTC1-32DT
DC input
/ trans output
+COM type
/ sink type
16 pts
/16 pts
Photocoupler
/ photocoupler
24VDC/24VDC
14 V min.
AJ65SBTC1-32DT1
DC input
/ trans output
+COM type
/ sink type
16 pts
/16 pts
Photocoupler
/ photocoupler
24VDC/24VDC
AJ65SBTC1-32DT2
DC input
/ trans output
+COM type
/ sink type
16 pts
/16 pts
Photocoupler
/ photocoupler
24VDC/24VDC
AJ65SBTC1-32DT3
DC input
/ trans output
+COM type
/ sink type
16 pts
/16 pts
Photocoupler
/ photocoupler
AJ65SBTC4-16DT
24VDC/24VDC
Maximum
Load Current
Output
Input
Response Time Leakage
Response
Current
Time
OFF–ON ON–OFF
Zener diode
Four wire type
/ Four wire type
16 points
1 common
40mA
0.1 mA
max.
Zener diode
Four wire type
/ Four wire type
16 points
1 common
40mA
1.5 ms
max.
0.25 mA
max.
Zener diode
One wire type
/ One wire type
32 points
1 common
50mA
0.5 ms
max.
1.5 ms
max.
0.25 mA
max.
Zener diode
One wire type
/ One wire type
32 points
1 common
50mA
1.5 ms
max.
0.5 ms
max.
1.5 ms
max.
0.1 mA
max.
Zener diode
One wire type
/ One wire type
32 points
1 common
50mA
0.2 ms
max.
0.5 ms
max.
1.5 ms
max.
0.1 mA
max.
Zener diode
One wire type
/ One wire type
32 points
1 common
50mA
2.4A
1.5 ms
max.
0.5 ms
max.
1.5 ms
max.
0.25 mA
max.
0.5A
2.4A
1.5 ms
max.
0.5 ms
max.
1.5 ms
max.
6 V max.
0.1A
1.6A
1.5 ms
max.
0.5 ms
max.
15 V min.
3 V max.
0.1A
1.6A
0.2 ms
max.
14 V min.
6 V max.
0.1A
1.6A
1.6A
15 V min.
3 V max.
0.1A
External
Internal
Surge
Connection Wire Common
Current
Suppression Type on Input/ Connection
Consumption
Output Sides
+COM: Positive common (sink) -COM: Negative common (source)
Mitsubishi Electric Automation
|
Distributed I/O 351
AJ65VBTCUo-16o
AJ65VBTCUo-8o
2. Transmission speed
setting switch
Setting value
40
20
10
8
4
2
1
4
2
Transmission speed
0
156 kbps
1
625 kbps
2
2.5 Mbps
3
5.0 Mbps
4
10 Mbps
1
40
20
10
8
4
2
1
4
2
S
T
A
T
I
O
N
N
O
B
R
A
T
E
1
1. Operation LED display
S
T
A
T
I
O
N
3
LED
name
N
O
B
2
R
A
T
E
PW
L RUN
3. Station number setting switches
L ERR
A J65VBTCU3-16D1
A J65VBTCU3-8D1
"10," "20," and "40" in STATION NO. are used for
setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for
setting the first digit of the station number.
CON
A
CON
B
L
I
N
K
CON
A
4
X0 to 1F
PW
L RUN
L RUN
X1
X4
Connector pin no.
1
0
1
2
3
4
5
6
7
X3
Turns on in case of a transmission error (CRC
error) and turns off via timeout (L RUN also turns
off). It turns on if the settings for station number
and transmission speed are wrong. It flashes if the
station-number and transmission-speed settings
are changed while the communication is active.
Y0 to 1F
Displays the on/off status of input/output.
L ERR
L ERR
X2
4. One-touch connector
for communication
Turns on when normal data is received from the
master station, and turns off via timeout.
L
I
N
K
CON
B
PW
X0
Item checked
Turns on when the power supply to the remote
I/O module is turned on.
0
1
2
3
4
5
6
7
6
X5
4321
8
9
A
B
C
D
E
F
X6
X7
X0∼X7
Pin no.
4
3
2
1
Name
SLD
NC
V- / I-
V+ / I+
P
W
／
A
U
CON X
D
CON
C
X8∼XF
5. One-touch connector
for power supply and FG
Connector pin no.
54321
P
W
／
A
U
CON X
D
CON
C
5
6. Connector for input/output signals
Pin no.
5
4
3
2
1
Name
FGI
AG
24V
24V
FG
AJ65SBTCo-16o
Operation LED display
X0 1
2 3
4
5 6
7
X8 9 A B C D E
F
STATION NO.
40 20 10 8 4 2
Transmission speed
setting switch
B RATE
1 4 2 1
Setting value
ON
AJ65SBTC4-16D
DA
DG
DB
+24V
SLD
24G
(FG)
X0
X8
+24V
24G
X1
X9
+24V
24G
X2
XA
+24V
24G
X3
XB
+24V
24G
X4
XC
+24V
24G
X5
XD
+24V
24G
X6
XE
+24V
24G
X7
XF
+24V
24G
CTL+
COM-
Transmission speed
0
156 kbps
1
625 kbps
2
2.5 Mbps
3
5.0 Mbps
4
10 Mbps
Station number
setting switches
"10," "20," and "40" in STATION NO. are used for
setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for
setting the first digit of the station number.
Terminal block for communication
DIN rail hook
Connector for input/output signals
AJ65SBTCo-32o
Transmission speed
setting switch
Operation LED display
LED
name
PW
Item checked
Turns on when the power supply to the digital I/O
module is turned on.
PW L RUN L ERR
L RUN
L ERR
X0 to 1F
X0 to F/
Y10 to 1F
Y0 to 1F
Turns on in case of a transmission error (CRC
error) and turns off via timeout (L RUN also turns
off). It turns on if the settings for station number
and transmission speed are wrong. It flashes
if the station-number and transmission-speed
settings are changed while the communication
is active.
Displays the on/off status of input/output.
X8 9 A B C D E F
X10 11 12 13 14 15 16 17
X18 19 1A 1B 1C 1D 1E 1F
DB
DG
+24V
SLD
A J65SBTC1-32D1
24G
(FG)
STATION NO.
B RATE
40 20 10 8 4 2 1 4 2 1
X0-XF
Setting value
ON
X10-X1F
X0
X4
X8
XC
X10
X14
X18
X1C
X1
X5
X9
XD
X11
X15
X19
X1D
X2
X6
XA
XE
X12
X16
X1A
X1E
X3
X7
XB
XF
X13
X17
X1B
X1F
COM
COM
Terminal block for communication
Transmission speed
0
156 kbps
1
625 kbps
2
2.5 Mbps
3
5.0 Mbps
4
10 Mbps
Station number
setting switches
"10," "20," and "40" in STATION NO. are used for
setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for
setting the first digit of the station number.
Lit in ON state and unlit in OFF state.
Connector for input/output signals
352
3 4 5 6 7
MITSUBISHI
DA
Turns on when normal data is received from the
master station, and turns off via timeout.
X0 1 2
DIN rail hook
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Guide to Module Features
External Dimensions
40
AJ65SBTC1-32o
AJ65SBTC4-16o
118
109mm +10 (mounting pitch)
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
16.5
PW L RUN L ERR
3 4 5 6 7
X8 9 A B C D E F
X10 11 12 13 14 15 16 17
X0 1 2
X18 19 1A 1B 1C 1D 1E 1F
MITSUBISHI
DB
DG
+24V
SLD
ON
24G
(FG)
X10-X1F
X0
X4
X8
XC
X10
X14
X18
X1C
X1
X5
X9
XD
X11
X15
X19
X1D
X2
X6
XA
XE
X12
X16
X1A
X1E
X3
X7
XB
XF
X13
X17
X1B
X1F
COM
COM
4
50
DA
STATION NO.
B RATE
40 20 10 8 4 2 1 4 2 1
X0-XF
A J65SBTC1-32D1
AJ65VBTCUo-8o
AJ65VBTCUo-16o
31
41
62
31
60
62
16.5
16.5
A J65VBTCU3-8D1
A J65VBTCU3-16D1
CON
A
CON
B
X0
CON
A
L
I
N
K
CON
B
L
I
N
K
PW
PW
L RUN
L RUN
L ERR
L ERR
X1
X3
X4
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
115
X2
115
X5
X6
X7
X0~X7
CON
C
CON
D
X8~XF
P
W
/
A
U
X
CON
C
CON
D
(Side view shows power and network connectors installed.)
8
9
A
B
C
D
E
F
P
W
/
A
U
X
(Side view shows power and network connectors installed.)
External Connections
Input Modules
AJ65SBTC1-32D • S
56JA 1D23-1CTB
AJ65SBTC4-16D type
Sink input
type
1
2
3
4
5
6
7
Module power
supply
DA
DB
DG
SLD
+24V
FG
24G
Isolation
DC/DC
DA
DB
DG
SLD
+24V
FG
24G
Isolation
DC/DC
Four wire type sensor (sink output)
Detection
circuit
1
2
3
4
5
6
7
Module power supply
R
Black (white)
Orange (orange)
Brown (red)
Blue (black)
R
COM1
1
2
R
3
R
4
R
R
CON1
1
2
R
3
R
4
Three wire type sensor (sink output)
Detection
circuit
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Unit: mm
Black (white)
Orange (orange)
Brown (red)
Blue (black)
COM2
1
R
2
R
3
4
R
R
CON2
1
2
Two wire type sensor (sink output)
R
3
R
4
Detection
circuit
Black (white)
Orange (orange)
Brown (red)
Blue (black)
COM8
1
I/O power supply
4
3
Sink/source selector switch
Sink
8 CTL+
9 COM-
R
CON8
1
2
R
3
Source
R
R
2
R
R
4
I/O power supply
8 COM
9 COM
Mitsubishi Electric Automation
|
Distributed I/O 353
AJ65VBTCU3-8D1 type
1
2
3
4
5
LINK CABLE
(IN)
AJ65SBTC4-16D type
Source input
1
2
3
4
5
6
7
Module power
supply
DA
DB
DG
SLD
+24V
FG
24G
Isolation
Detection
circuit
Four wire type sensor (source output)
R
One-touch connector
for communication
R
COM1
Black (white)
Orange (orange)
Brown (red)
Blue (black)
1
2
1
2
3
4
5
UNIT POWER CABLE (IN)
R
3
R
4
I/O POWER CABLE (IN)
Three wire type sensor (source output)
Detection
circuit
1
2
3
4
5
LINK CABLE
(OUT)
DC/DC
1
R
2
R
3
1
2
3
4
5
UNIT POWER
CABLE (OUT)
I/O POWER
CABLE (OUT)
COM2
Black (white)
Orange (orange)
Brown (red)
Blue (black)
4
CON.A
DA
DB
DG
NC
SLD
CON.B
1 DA
2 DB
3 DG
4 NC
5 SLD
1
2
3
4
5
Isolation
CON.C
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
CON.D
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
DC/DC
One-touch connector
for power supply and FG
Three wire type sensor (sink output)
R
2
R
3
Two wire type sensor (sink output)
Sink/source selector switch
CON2
1
2
3
4
Detection
circuit
Sink
8 CTL+
9 COM-
(sink output)
AJ65VBTCU3-16D1 type
Out put M
1
2
3
4
5
LINK CABLE
(IN)
1
2
3
4
5
LINK CABLE
(OUT)
One-touch connector
for communication
1
2
3
4
5
UNIT POWER CABLE (IN)
I/O POWER CABLE (IN)
1
2
3
4
5
UNIT POWER
CABLE (OUT)
I/O POWER
CABLE (OUT)
CON.A
DA
DB
DG
NC
SLD
CON.B
1 DA
2 DB
3 DG
4 NC
5 SLD
1
2
3
4
5
R
R
Source
I/O power supply
R
4
CON8
1
2
3
4
R
R
Detection
circuit
1
R
COM8
Black (white)
Orange (orange)
Brown (red)
Blue (black)
CON1
1
2
3
4
Detection
circuit
Two wire type sensor (sink output)
odules
AJ65SBTC1-32 type
CON.C
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
CON.D
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
Isolation
DC/DC
DA
DB
DG
SLD
+24V
FG
24G
1
2
3
4
5
6
7
Isolation
DC/DC
Module power supply
1
L
CON1
2
3
4
L
One-touch connector
for power supply and FG
Three wire type sensor (sink output)
Two wire type sensor (sink output)
R
R
Detection
circuit
CON1
1
2
3
4
CON8
CON2
1
2
3
4
R
1
L
R
Detection
circuit
2
3
(sink output)
4
L
CON16
1
2
3
4
R
R
I/O power supply
(external power supply)
Constant
voltage
circuit
8 CTL+
9 COM-
Load power supply
In case I/O power supply
and load power supply are common
L
8 CTL+
9 COM-
S
56JA 1T23-1CTB
AJ65VBTCU2-8 type
type
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
Module power supply
L
1
L
4
Isolation
1
2
3
4
5
LINK CABLE
(IN)
DC/DC
1
2
3
4
5
LINK CABLE
(OUT)
CON1
2
One-touch connector
for communication
3
1
2
3
4
5
UNIT POWER CABLE (IN)
I/O POWER CABLE (IN)
CON8
L
1
2
I/O power supply
(external power supply)
8 CTL+
9 COM-
Constant
voltage
circuit
L
Load power supply
In case I/O power supply
and load power supply are common
L
8 CTL+
9 COM-
Isolation
DC/DC
Constant
voltage circuit
4
L
354
CON.C
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
CON.D
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
One-touch connector
for power supply and FG
3
L
1
2
3
4
5
UNIT POWER
CABLE (OUT)
I/O POWER
CABLE (OUT)
CON.A
DA
DB
DG
NC
SLD
CON.B
1 DA
2 DB
3 DG
4 NC
5 SLD
1
2
3
4
5
L
CON1
1
2
3
4
CON2
1
2
3
4
CON8
1
2
3
4
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
External Connections
External Connections
AJ65VBTCU2-16T type
1
2
3
4
5
LINK CABLE
(IN)
1
2
3
4
5
LINK CABLE
(OUT)
One-touch connector
for communication
1
2
3
4
5
UNIT POWER CABLE (IN)
I/O POWER CABLE (IN)
1
2
3
4
5
UNIT POWER
CABLE (OUT)
I/O POWER
CABLE (OUT)
AJ65SBTC1-32DT • AJ65SBTC1-32DT1 type
DA
DB
DG
SLD
+24V
FG
24G
1
2
3
4
5
6
7
CON.C
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
CON.D
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 +24V(I/O)
5 24G(I/O)
Isolation
DC/DC
Module power supply
Isolation
CON1∼CON4
1
DC/DC
R
2
R
3
4
R
R
One-touch connector
for power supply and FG
CON5∼CON8
Constant
voltage circuit
1
L
2
CON1
1
2
3
4
L
3
4
L
CON2
1
2
3
4
L
I/O power supply
(external power supply)
Constant
voltage
circuit
8 COM+
9 COM-
Load power supply
CON16
1
2
3
4
L
In case I/O power supply
and load power supply are common
L
8 COM+
9 COM-
AJ65SBTC1-32DT2 • AJ65SBTC1-32DT3 type
AJ65SBTC4-16DT type
Example of Connection with 4-, 3-, and 2-wire type Sensors
DA
DB
DG
SLD
+24V
FG
24G
1
2
3
4
5
6
7
Isolation
DC/DC
Module power supply
1
2
3
4
5
6
7
CON1∼CON4
1
R
2
Module power
supply
R
3
4
Four wire type sensor
(sink output/sink input)
R
Detection
circuit
R
DA
DB
DG
SLD
+24V
FG
24G
Isolation
DC/DC
R
R
COM1
Black (white)
Orange (orange)
Brown (red)
Blue (black)
1
2
3
4
CON5∼CON8
1
L
Three wire type sensor (source output)
3
4
L
R
R
COM2
Detection
circuit
2
1
2
3
4
I/O power supply
(external power supply)
Two wire type sensor (sink output)
R
R
COM3
Detection
circuit
Constant
voltage
circuit
8 COM+
9 COM-
1
2
3
4
In case I/O power supply
and load power supply are common
L
8 CTL+
9 COM-
8 COM+
9 COM-
DC24V
AJ65SBTC4-16DT2 type
Example of Connection with 4-, 3-, and 2-wire type Sensors
1
2
3
4
5
6
7
Module power
supply
Detection
circuit
Four wire type sensor
(sink output/sink input)
Constant
voltage
circuit
Load power supply
DA
DB
DG
SLD
+24V
FG
24G
Other Example of Connection
1
2
3
4
5
6
7
Isolation
DC/DC
Module power
supply
DA
DB
DG
SLD
+24V
FG
24G
Isolation
DC/DC
R
R
COM1
Black (white)
Orange (orange)
Brown (red)
Blue (black)
1
(sink input)
2
3
R
R
COM1
1
4
2
3
4
Three wire type sensor (source output)
R
R
Detection
circuit
COM2
1
2
3
4
R
Two wire type sensor (sink output)
(sink output)
L
R
R
COM3
Detection
circuit
R
COM3
1
2
3
4
1
2
3
8 CTL+
9 COM8 CTL+
9 COM-
DC24V
Constant
voltage
circuit
4
Constant
voltage
circuit
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Combination Input/Output Modules
CON.A
1 DA
2 DB
3 DG
4 NC
5 SLD
CON.B
1 DA
2 DB
3 DG
4 NC
5 SLD
DC24V
Mitsubishi Electric Automation
|
Distributed I/O 355
n Intended for OEM System Designers needing to embed a CC-Link network connection in their own products.
n Each device offers differing amounts of discrete I/O to interface to the OEM device.
n PCB mounted device.
n All modules UL • cUL listed and CE certified.
Performance Specifications
Input Adapter
Item
AJ65MBTL1N-16D
I/O Combination Adapter
AJ65MBTL1N-16T
AJ65MBTL1N-32T
AJ65MBTL1N-16DT
DC input
DC input
Transistor output
Transistor output
DC input / Transistor output
+COM type
+COM type
Sink type
Sink type
+COM type / Sink type
16 points
32 points
16 points
32 points
8 points / 8 points
Photocoupler
Photocoupler
Photocoupler
Photocoupler
Photocoupler / Photocoupler
Input/Output Type
Number Of Input/ Output Points
Isolation Method
Output Adapter
AJ65MBTL1N-32D
Rated Input/ Load Voltage
24 VDC
24 VDC
12/24 VDC
12/24 VDC
24 VDC / 24 VDC
Maximum
Load Current
1 Point
—
—
0.1A
0.1A
0.1A
1 Common
—
—
1.6A
3.2A
0.8A
Operating
Voltage
ON Voltage
18 V min.
18 V min.
—
—
14 V min. / —
Response
Time
OFF Voltage
6 V max.
6 V max.
—
—
6 V max. / —
OFF—ON
1.5 ms max.
1.5 ms max.
1.0 ms max.
1.0 ms max.
1.5 ms max. / 1.0 ms max.
ON—OFF
1.5 ms max. / 1.0 ms max.
1.5 ms max.
1.5 ms max.
1.0 ms max.
1.0 ms max.
Leakage Current
—
—
0.1mA
0.1mA
±0.1mA
Surge Suppression
—
—
Zener diode
Zener diode
— / Zener diode
External Connection Wire Type
44 pins (2 rows)
62 pins (2 rows)
44 pins (2 rows)
62 pins (2 rows)
44 pins (2 rows)
Common Connection
16 points 1common
32 points 1common
16 points 1 common
32 points 1 common
16 points 1 common
Current Consumption
35mA
45mA
50mA
60mA
50mA
* +COM: Positive common (sink)
Cascade Connection Method
AJ65MBTL1N-16D
AJ65MBTL1N-16T
AJ65MBTL1N-16DT
OE-IN
AJ65MBTL1N-32D
AJ65MBTL1N-32T
OE-IN
A20
OE-IN
A20
OE-IN
A29
B20
OE-OUT
B20
OE-OUT
B29
B22
DA
B22
DA
B31
A29
OE-OUT
DA
B29
OE-OUT
B31
DA
DA
DA
CC-Link Embedded
I/O Adapters (2)
SD-IN
A19
A22
DB
B21
DG
A19
CC-Link Embedded
I/O Adapters (1)
A22
DB
B21
DG
FG
RD
A21
B18
A18
A17
RDGON
GND
B19
SLD
B19
SD-OUT
A18
RDGON
A17
GND
SD-IN
SD-OUT
RD
DB
B30
DG
SD-IN
A30
FG
RD
CC-Link Embedded
I/O Adapters (1)
A31
DB
A28
B30
DG
B27
A30
FG
DB
DG
SLD
B27
A27
FG
A31
A28
FG
B18
OPEN
CC-Link Embedded
I/O Adapters (2)
DB
DG
A21
RD
SD-IN
RDGON
A26
GND
B28
SD-OUT
A27
RDGON
A26
B28
SD-OUT
GND
(OPEN)
Reserve at least 5mm between I/O modules.
356
FG
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Remote I/O: AJ65MBTL1N-o
Embedded I/O Adapters
AJ65MBTL1N-o
LED display
LED name
Transmission speed
setting switch
Item checked
PW
Lit when the embedded I/O module of CC-Link is
turned on.
L RUN
Checks if the embedded I/O module of CC-Link
communicates correctly with the master station.
The lamp lights up upon reception of correct data
from the master station, or it is unlit upon time-out.
Setting value
A J65MBTL1N-16DT
PW
XO~XF
/ XO~X1F
YO~YF
/ YO~Y1F
L RUN
L ERR.
ON
Lit: Communication data error (CRC error), out-ofrange setting at station number setting or data
link transmission speed setting switch
Blink at certain intervals: Modification of station
number setting or transmission speed setting
switch setting in power-on state
Blink at irregular intervals: Missing terminator,
noise effect on embedded I/O module or special
cable of CC-Link
L ERR
X0 X1 X2 X3 X4 X5 X6 X7
Y8 Y9 YA YB YC YD YE YF
Transmission speed
0
156kbps
1
625kbps
2
2.5Mbps
3
5.0Mbps
4
10Mbps
INPUT / OUTPUT UNIT
402010 8 4 2 1 4 2 1
STATION NO.
B RATE
DATE
JAPAN
Station number
setting switches
"10," "20," and "40" in STATION NO. are
used for setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are
used for setting the first digit of the station
number.
The ON/OFF state of the input/output is
displayed.
Lit in ON state and unlit in OFF state.
External Dimensions
AJ65MBTL1N-16DT
AJ65MBTL1N-16T
AJ65MBTL1N-16D
Unit: mm
AJ65MBTL1N-32D
AJ65MBTL1N-32T
A J65MBTL1N-16DT
L ERR.
X0 X1 X2 X3 X4 X5 X6 X7
D=22
L RUN
D=22
PW
Y8 Y9 YA YB YC YD YE YF
ON
INPUT / OUTPUT UNIT
402010 8 4 2 1 4 2 1
STATION NO.
B RATE
DATE
JAPAN
W=85
H=31.5
W=53
3.5
3.5
H=31.5
A22
19.5
ø0.95±0.04
A31
A01
A01
B31
B22
B01
B01
Recommended circuit board dimensions
top view
60±0.1
2±0.05
2±0.05
42±0.1
2±0.05
7.5
5.5
5.5
ø0.95±0.04
7.5
5.5
2±0.05
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Adapter Features
Recommended circuit board dimensions
top view
Mitsubishi Electric Automation
|
Distributed I/O 357
Input Module
AJ65MBTL1N-16D
AJ65MBTL1N-32D
Pin No.
Signal name
Circuit board
Pin No.
Signal name
DA
B22
DA
DB
A22
DB
DG
B21
SLD
A21
FG
B20
OE-OUT
A20
OE-IN
B19
SD-OUT
A19
2
B31
A31
DB
B30
DG
A30
FG
B29
OE-OUT
SD-IN
OE-IN
B28
SD-OUT
A28
SD-IN
B27
RD
A27
RDGON
B26
Vacant
B18
RD
A18
RDGON
A26
GND
B17
Vacant
B25
Vacant
3
GND
Vacant
Vacant
B15
Vacant
X0
B23
A15
Vacant
X1
A23
X0
B14
X0
X2
B22
X2
X1
A14
X1
X3
A22
X3
X2
B13
X2
X4
B21
X4
X3
A13
X3
X5
A21
X5
X4
B12
X4
X6
B20
X6
X5
A12
X5
X7
A20
X8
B19
X6
B11
X6
X9
A19
X9
X7
A11
X7
XA
B18
XA
X8
B10
X8
XB
A18
XB
X9
A10
X9
XC
B17
XC
XA
B09
XA
XD
A17
A25
R
R
Vacant
A24
Vacant
X0
X8
XD
A09
XB
XE
B16
B08
XC
XF
A16
XF
A08
XD
B15
X10
XE
B07
X10
X11
A15
X11
XF
A07
XF
COM
B06
COM
X12
X13
B14
A14
X12
X13
A06
COM
X14
B13
X14
B05
Vacant
X15
A13
X15
A05
Vacant
X16
B12
X16
B04
X17
A12
Vacant
X18
B11
A04
Vacant
X19
A11
X19
B03
Vacant
X1A
B10
X1A
A03
Vacant
X1B
A10
X1B
B02
+24V
X1C
B09
X1C
A02
+24V
X1D
A09
X1D
B01
24G
X1E
B08
X1E
A01
24G
X1F
A08
X1F
COM
B07
COM
A07
COM
B06
Vacant
A06
Vacant
B05
Vacant
A05
Vacant
B04
Vacant
A04
Vacant
B03
Vacant
A03
Vacant
B02
+24V
A02
+24V
B01
24G
A01
24G
22000pF
630V
+24V
1
Isolation
DC/DC
Output Module
Module power
supply
AJ65MBTL1N-16T
22000pF
630V
+24V
Signal name
Circuit board
Pin No.
Signal name
DA
B22
DA
DB
A22
DB
DG
B21
DG
SLD
A21
FG
B20
OE-OUT
1
24G
AJ65MBTL1N-16T
R
X7
XB
XE
R
X1
XD
R
Internal circuit
Vacant
B24
XC
DC24V
XE
X17
X18
R
R
COM
Isolation
DC/DC
FG
リンク
IC
Internal circuit
Output Module
Combination Input / Output Module
AJ65MBTL1N-32T
AJ65MBTL1N-16DT
A20
OE-IN
B19
SD-OUT
A19
SD-IN
B18
RD
A18
RDGON
B17
Vacant
A17
GND
B16
Vacant
A16
Vacant
B15
Vacant
A15
Vacant
Y0
B14
Y0
Y1
A14
Y1
Y2
B13
Y2
Y3
A13
Y3
A29
OE-IN
Y4
B12
Y4
B28
SD-OUT
A20
OE-IN
Y5
A12
Y5
A28
SD-IN
B19
SD-OUT
Y6
B11
Y6
B27
RD
A19
SD-IN
Y7
A11
A27
RDGON
Y8
B10
B26
Vacant
Y9
A10
Y9
A26
GND
YA
B09
YA
B25
Vacant
A25
B24
Vacant
Vacant
2
L
DC24V
A29
A16
FG
L
DA
SLD
Internal circuit
R
AJ65MBTL1N-32D
Pin No. Signal name
DB
B16
24G
Signal name
Circuit board
Pin No.
YB
A09
YB
B08
YC
A08
YD
YE
B07
YE
AJ65MBTL1N-32T
Signal name
DA
B22
DG
DB
A22
DB
A30
FG
DG
B21
DG
B29
OE-OUT
SLD
A21
FG
B20
OE-OUT
SLD
DA
Internal circuit
B18
RD
A18
RDGON
B17
Vacant
A17
GND
B16
Vacant
A16
Vacant
B15
Vacant
A15
Vacant
X0
B14
X0
X1
A14
X1
2
A24
Vacant
B23
Y0
Y1
A23
Y1
Y2
B22
Y2
Y3
A22
Y3
Y4
B21
Y4
X2
B13
X2
Y5
A21
Y5
X3
A13
X3
Y6
B20
Y6
X4
B12
X4
Y7
A20
X5
A12
X5
Y8
B19
X6
B11
X6
X7
A11
X7
Y8
B10
Y8
A07
YF
CTL+
B06
CTL+
COM-
A06
CTL+
B05
COM-
A05
COM-
B04
Vacant
A04
Vacant
B03
Vacant
A03
Vacant
B02
+24V
A02
+24V
B01
24G
YD
A17
YD
A01
24G
YE
B16
YE
YF
A16
YF
Y10
B15
Y11
A15
Y12
Y13
B14
Y12
A14
Y13
Y14
B13
Y14
DC24G
Y15
A13
Y16
B12
Y17
A12
Y18
B11
+24V
24G
FG
1
DC/DC
*1: Add according to environmental noise when necessary.
Not supplied.
*2: Connect A17 and A18 if cascade connection is not made.
*3: Connect A26 and A27 if cascade connection is not made.
DC12/24V
Module power
supply
L
Y7
Y8
Y9
A19
Y9
YA
B18
YA
YB
A18
YB
YC
B17
YC
YB
B08
YC
A07
YF
B06
DC24V
A06
DC24V
Y15
B05
DC24G
Y16
A05
DC24G
B04
Vacant
A04
Vacant
B03
Vacant
A03
Vacant
B02
+24V
A02
+24V
B01
24G
A01
24G
Y17
Y18
Y19
Y1B
A10
Y1B
Y1C
B09
Y1C
Y1D
A09
Y1D
Y1E
B08
Module power
supply
+24V
24G
Y1E
Y1F
A08
Y1F
CTL+
B07
CTL+
CTL+
A07
CTL+
COM-
B06
COM-
COM-
A06
COM-
B05
COM-
A05
COM-
B04
Vacant
A04
Vacant
B03
Vacant
A03
B02
Vacant
+24V
A02
+24V
B0 1
24G
A0 1
24G
22000pF
630V
1
FG
Constant
voltage
circuit
COMCOM-
Isolation
DC/DC
Internal circuit
R
R
R
R
Y9
B07
L
DC24V
リンク
IC
YA
A08
Y1A
FG
A09
YF
B10
1
B09
YE
A11
24G
A10
YB
YD
Y19
+24V
Y9
YA
YC
DC24V
Y10
Y11
Y1A
22000pF
630V
L
AJ65MBTL1N-16DT
DA
Y0
L
Isolation
Signal name
DB
B30
YF
22000pF
630V
Pin No.
A31
3
Constant
voltage
circuit
Circuit board
B31
DB
Y8
YD
Signal name
DA
DG
Y7
YC
Module power
supply
358
Circuit board
DA
DG
A17
DC24V
Module power
supply
DG
AJ65MBTL1N-16D
リンク
IC
YD
YE
Constant
voltage
circuit
Isolation
DC/DC
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
External Connections
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CC-Link Remote I/O: AJ65FBTAo-16o• AJ65SBTW4-16o
Water Resistant Connector Type
n Water resistant I/O power and network connections certified to IP67.
n “F Type” modules can be replaced without disrupting the network.
n Standard M12 connections.
n F Type modules offer built-in terminating resistors, 55°C operating temperature.
n W Type modules offer waterproof screw terminal connections for power and network connections.
n Connectors available from a variety of third party sources.
n All models UL • cUL listed and CE certified.
Dustproof and waterproof connection caps are available to protect unused connectors. See the introduction to this section.
AJ65SBTW4-16o
Performance Specifications
AJ65FBTA42-16o
Input Module Model Name
I/O Module Model Name
Output Module Model Name
Item
Input/Output Type
Number of Input/
Output Points
Isolation Method
Rated Input/
Load Voltage
AJ65FBTA4-16D
AJ65FBTA4-16DE
AJ65SBTW4-16D
AJ65FBTA2-16T
AJ65FBTA2-16TE
AJ65FBTA42-16DT
AJ65FBTA42-16DTE
AJ65SBTW4-16DT
DC input
DC input
DC input
Transistor output
Transistor output
DC input
/ transistor output
DC input
/ transistor output
DC input
/ transistor output
+COM: Positive
common
(Sink)
–COM: Negative
common
(Source)
+COM: Positive common(Sink)
–COM: Negative common(Source)
common type
Sink type
Source type
+COM: Positive
common (Sink)
/ sink type
–COM: Negative
common (Source)
/ source type
+COM: Positive
common (Sink)
/ sink type
16 points
16 points
16 points
16 points
16 points
Photocoupler
Photocoupler
Photocoupler
Photocoupler
Photocoupler
8 points/8 points
Photocoupler
/photocoupler
8 points/8 points
Photocoupler
/photocoupler
8 points/8 points
Photocoupler
/photocoupler
24 VDC
24 VDC
24 VDC
12/24VDC
12/24VDC
24 VDC/24 VDC
24 VDC/24 VDC
24 VDC/24 VDC
Maximum 1 Point
Load
1 Common
Current
—
—
—
0.5A
1.0A
0.5A
1.0A
0.5A
—
—
—
4.0A
4.0A
2.4A
4.0A
2.4A
Operating ON Voltage
Voltage
OFF Voltage
14 V min.
14 V min.
14 V min.
—
—
14 V min.
14 V min.
14 V min.
6 V max.
6 V max.
6 V max.
—
—
6 V max.
6 V max.
6 V max.
1.5 ms max.
1.5 ms max.
1.5 ms max.
0.5 ms max.
0.5 ms max.
1.5 ms/0.5 ms max.
1.5 ms/0.5 ms max.
1.5 ms/0.5 ms max.
1.5 ms max.
1.5 ms max.
1.5 ms max.
1.5 ms max.
1.5 ms max.
1.5 ms/1.5ms max.
1.5 ms/1.5 ms max.
1.5 ms/0.5 ms max.
Surge Suppression
—
—
—
Zener diode
Zener diode
Zener diode
Zener diode
Zener diode
External Connection
Wire Type
Four wire type
Four wire type
Four wire type
Two wire type
Two wire type
Four wire type
/ two wire type
Four wire type
/ two wire type
Four wire type
/ two wire type
16 points
1 common
16 points
1 common
16 points
1 common
16 points
1 common
16 points
1 common
8 points 1 common
/8 points 1 common
8 points 1 common
/8 points 1 common
8 points 1 common
/8 points 1 common
40mA
40mA
35mA
50mA
50mA
50mA
45mA
—
Fitting cable size
ø4.0mm to 8.0mm / -
OFF—ON
Response
Time
ON—OFF
Common
Connection
Current Consumption
Cable Diameter Range
For Water Resistant
Compression Fitting
—
40mA
Fitting cable size
—
—
—
—
Mitsubishi Electric Automation
ø4.0mm to 8.0mm / -
|
Distributed I/O 359
AJ65FBTAo-16o
Main body connector
Terminal resistor setting
Station number setting switches
Dip switch 1
Dip switch 2
Description
OFF
ON
OFF
ON
OFF
OFF
ON
ON
No terminal resistor
110 terminal On
130 terminal On
Setting prohibited
"10," "20," and "40" in STATION NO. are used for setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for setting the first
digit of the station number.
TERMINATION
110Ω
130Ω
ON
Communication adapter
(back side)
Communication adapter (front side)
Communication adapter connector
Transmission speed setting switch
Setting value
0
1
2
3
4
Waterproof connector
for transmission line
ON
40 20 10 8 4 2 1 4 2 1
STATION NO
Communication
adapter
B RATE
Transmission speed
156 kbps
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
A J65FBTA42-16DTE
FG metal fittings
Operating condition LED display
PROTECT
Y8
Y9
YA
YB
YC
YD
YE
YF
Description
POWER
On: Power supply is turned on.
L RUN
On: Communication is normal.
L ERR.
Off: Communication is normal.
Off: Normal
PROTECT
On: Protection function is enabled.
Y
Y
Waterproof connector
for power-supply line
Y
Y
Y
Y
Y
Y
Waterproof connector
for input/output
*All switches are mounted internally to maintain water resistance.
AJ65SBTW4-16o
Terminal block
Transmission speed setting switch
Setting value
0
1
2
3
4
Sink/source selector switch
(only for AJ65SBTW4-16D)
SINK
Transmission speed
156 kbps
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
Station number setting switches
SOURCE
Switch the +COM, –COM type to either
sink or source type.
"10," "20," and "40" in STATION NO. are used for setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for setting the first
digit of the station number.
Module top-cover mounting screw
Operation LED display
Waterproof connector
for input/output line
LINK CABL
Module front-cover mounting screw
LINK CABL
LED name
IN
OUT
POWER CABL
L RUN
L ERR.
Y8
Y9
YA
YB
YC
YD
YE
YF
PW
POWER CABL
CON1
CON3
CON5
CON7
CON2
CON4
CON6
CON8
X0
X1
X2
X3
X4
X5
X6
X7
PW
L RUN
L ERR
Turns on in case of a transmission error (CRC
error) and turns off via
timeout (L RUN also turns off). It turns on if the
settings for station number and transmission
speed are wrong. It turns on if the stationnumber and transmission-speed settings are
changed while the communication is active.
X0 to 1F
Y0 to 1F
Displays the on/off status of input. The LEDs
turn on in the "On" state, and off in the "Off"
state.
STATION NO.
AJ65SBTW4-16DT
FG metal fittings
Water resistant compression fitting for transmission/module power supply line.
360
Item checked
Turns on when the power supply to the remote
I/O module is turned on.
Turns on when normal data is received from
the master station, and turns off via timeout.
*All switches and terminal blocks are mounted internally
to maintain water resistance.
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Module Features
External Dimensions
AJ65FBTA4-16D • AJ65FBTA4-16DE
AJ65FBTA2-16T • AJ65FBTA2-16TE
AJ65FBTA42-16DT • AJ65FBTA42-16DTE
Two 4.5mm x 6mm oblong holes for M4 mounting screws
AJ65SBTW4-16D • AJ65SBTW4-16DT
+1
48
50±1
34±0.5
26.5
4.3
18.3
184. 7
180
6
(2.6)
21.3
2.1
192±1
+1
24
33
180
2.1
25
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
LINK CABL
IN
POWER CABL
LINK CABL
OUT
POWER CABL
(2.6)
PW
CON1
CON3
CON5
CON7
CON2
CON4
CON6
CON8
L RUN
L ERR.
Y8
Y9
YA
YB
YC
YD
YE
YF
X0
X1
X2
X3
X4
X5
X6
X7
25
STATION NO.
AJ65SBTW4-16DT
Terminal Label
6
4.1
21.7
M4 mounting screw
32
35
External Connections
Input Module
AJ65FBTA4-16DE
AJ65FBTA4-16D
LINK OUT
UNIT POWER
Module
mounting screw (FG)
AUX.
Detection
circuit
I/O connector
Four wire type
sensor (sink output)
LINK IN
4
2
3
1
4
2
3
1
5
Communication
circuit
110Ω
R
R
1 30Ω
LINK OUT
Terminal
resistor
setting switch
UNIT POWER
1
3
5
2
4
DC/DC
Module
mounting screw (FG)
AUX.
1
3
5
2
4
I/O connector
Four wire type
sensor (sink output)
4
2
1
3
5
R
R
R
Three wire type sensor
(sink output)
Detection
circuit
Detection
circuit
LINK IN
4
2
3
1
5
1
3
5
2
4
Communication
circuit
110Ω
R
R
130Ω
Terminal
resistor
setting switch
DC/DC
1
3
5
2
4
4
2
1
3
5
R
R
R
Three wire type sensor
(sink output)
R
4
2
1
3
5
4
2
3
1
R
4
2
1
3
5
R
R
R
R
R
R
R
R
Two wire type sensor
(sink output)
Detection
circuit
200 0
12
30
68
60
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
25
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
60 0
Two wire type sensor
(sink output)
4
2
1
3
5
4
2
1
3
5
R
R
R
R
R
R
R
Pin no.
1
2
3
4
5
Pin no.
1
2
3
4
5
Pin no.
X0
—
X1
X2
—
X3
X4
—
X5
X6
—
X7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Communication connector
LINK IN
SLD
DB
DG
DA
No pin
Power supply connector
UNIT POWER
+24V (UNIT)
Vacant
24G (UNIT)
Vacant
FG
I/O connector
Pin no.
Pin no.
+24V
X1
X8
—
24G
X9
X0
Vacant
+24V
X3
XA
—
24G
XB
X2
Vacant
+24V
X5
24G
X4
Vacant
+24V
X7
24G
X6
Vacant
XC
—
XD
XE
—
XF
R
Pin layout
LINK OUT
SLD
DB
DG
DA
Vacant
AUX.
+24V (I/O)
Vacant
24G (I/O)
Vacant
FG
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Pin no.
+24V
X9
24G
X8
Vacant
+24V
XB
24G
XA
Vacant
+24V
XD
24G
XC
Vacant
+24V
XF
24G
XE
Vacant
LINK IN
Male
2
3
1
4
LINK OUT
Female
2
1
4 53
Pin no.
1
2
3
4
5
Pin no.
1
2
3
4
5
Pin no.
UNIT POWER/AUX.
Male
X0
—
X1
1
2
3 54
X2
—
X3
I/O connector
Female
2
1
4 53
Front view
X4
—
X5
X6
—
X7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Communication connector
LINK IN
SLD
DB
DG
DA
No pin
Power supply connector
UNIT POWER
+24V (UNIT)
Vacant
24G (UNIT)
Vacant
FG
I/O connector
Pin no.
Pin no.
+24V
X1
X8
—
24G
X9
X0
Vacant
+24V
X3
XA
—
24G
XB
X2
Vacant
+24V
X5
24G
X4
Vacant
+24V
X7
24G
X6
Vacant
XC
—
XD
XE
—
XF
LINK OUT
SLD
DB
DG
DA
Vacant
AUX.
+24V (I/O)
Vacant
24G (I/O)
Vacant
FG
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Pin no.
+24V
X9
24G
X8
Vacant
+24V
XB
24G
XA
Vacant
+24V
XD
24G
XC
Vacant
+24V
XF
24G
XE
Vacant
Mitsubishi Electric Automation
|
Distributed I/O 361
Output Modules
AJ65FBTA2-16T
AJ65FBTA2-16TE
Pin no.
1
2
3
4
5
Pin no.
LINK IN
Communication circuit
LINK OUT
SLD
SLD
DB
DB
DG
DG
DA
DA
No pin
Vacant
Power supply connector
UNIT POWER
1
2
3
4
5
Pin no.
Pin no.
Communication circuit
AUX.
+24V (UNIT)
+24V (I/O)
Vacant
Vacant
24G (UNIT)
24G (I/O)
Vacant
Vacant
FG
FG
I/O connector
Pin Signal Pin Signal
no. name no. name
1 +24V
1 +24V
2 Y1
2 Y9
Y0
Y8
— 3 Vacant — 3 Vacant
Y1
Y9
4 Y0
4 Y8
5 Vacant
5 Vacant
1 +24V
1 +24V
2 Y3
2 YB
Y2
YA
— 3 Vacant — 3 Vacant
Y3
YB
4 Y2
4 YA
5 Vacant
5 Vacant
1 +24V
1 +24V
2 Y5
2 YD
Y4
YC
— 3 Vacant — 3 Vacant
Y5
YD
4 Y4
4 YC
5 Vacant
5 Vacant
1 +24V
1 +24V
2 Y7
2 YF
Y6
YE
— 3 Vacant — 3 Vacant
Y7
YF
4 Y6
4 YE
5 Vacant
5 Vacant
LINK OUT
UNIT POWER
Module
mounting screw
(FG)
AUX.
I/O connector
Load
L
L
Load
L
L
Load
L
L
362
4
2
3
1
4
2
3
1
5
1
3
5
2
4
1
3
5
2
4
110Ω
R
R
130Ω
Terminal
resistor
selector switch
DC/DC
Constant
voltage
circuit
LINK IN
LINK OUT
110Ω
4
2
3
1
5
R
R
130Ω
Terminal
resistor
selector switch
UNIT POWER
Module
mounting screw
(FG)
AUX.
1
3
5
2
4
1
3
5
2
4
I/O connector
4
2
1
3
5
Load
L
L
4
2
1
3
5
Load
L
L
4
2
1
3
5
4
2
3
1
Load
L
L
4
2
1
3
5
4
2
1
3
5
4
2
1
3
5
DC/DC
Constant
voltage
circuit
LINK OUT
SLD
SLD
DB
DB
DG
DG
DA
DA
No pin
Vacant
Power supply connector
UNIT POWER
AUX.
+24V (UNIT)
+24V (I/O)
Vacant
Vacant
24G (UNIT)
24G (I/O)
Vacant
Vacant
FG
FG
I/O connector
Pin Signal Pin Signal
no. name no. name
1 Vacant
1 Vacant
2 Y1
2 Y9
Y0
Y8
— 3 24G — 3 24G
Y1
Y9
4 Y0
4 Y8
5 Vacant
5 Vacant
1 Vacant
1 Vacant
2 Y3
2 YB
Y2
YA
— 3 24G — 3 24G
Y3
YB
4 Y2
4 YA
5 Vacant
5 Vacant
1 Vacant
1 Vacant
2 Y5
2 YD
Y4
YC
— 3 24G — 3 24G
Y5
YD
4 Y4
4 YC
5 Vacant
5 Vacant
1 Vacant
1 Vacant
2 Y7
2 YF
Y6
YE
— 3 24G — 3 24G
Y7
YF
4 Y6
4 YE
5 Vacant
5 Vacant
1
2
3
4
5
Communication
circuit
LINK IN
Communication
circuit
1
2
3
4
5
LINK IN
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
External Connections
External Connections
Combination Input / Output Modules
Detection
circuit
1
3
5
2
4
LINK OUT
UNIT POWER
1
3
5
2
4
DC/DC
Module mounting screw
(FG)
AUX.
4
2
1
3
5
Three wire type sensor
(sink output)
Detection
circuit
4
2
3
1
5
Terminal
resistor
setting switch
R
R
R
Two wire type sensor
(sink output)
R
R
R
R
R
Pin no.
1
2
3
4
5
R
Pin no.
1
2
3
4
5
Pin no.
X0
—
X1
X2
—
X3
X4
—
X5
X6
—
X7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Load
L
L
R
R
R
R
R
R
R
R
4
2
1
3
5
Pin layout
LINK OUT
SLD
DB
DG
DA
Vacant
AUX.
+24V (I/O)
Vacant
24G (I/O)
Vacant
FG
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
R
R
4
2
1
3
5
Communication connector
LINK IN
SLD
DB
DG
DA
No pin
Power supply connector
UNIT POWER
+24V (UNIT)
Vacant
24G (UNIT)
Vacant
FG
I/O connector
Pin no.
Pin no.
+24V
X1
Y8
—
24G
Y9
X0
Vacant
+24V
X3
YA
—
24G
YB
X2
Vacant
+24V
X5
YC
—
24G
YD
X4
Vacant
+24V
X7
YE
—
24G
YF
X6
Vacant
DC/DC
R
4
2
1
3
5
R
Load
L
L
Terminal
resistor
setting switch
R
4
2
1
3
5
Two wire type sensor
(sink output)
R
4
2
1
3
5
4
2
1
3
5
Three wire type sensor
(sink output)
R
4
2
1
3
5
1
3
5
2
4
I/O connector
Four wire type sensor
(sink output)
Communication
circuit
110Ω
R
R
130Ω
Constant
voltage
circuit
I/O connector
Four wire type sensor
(sink output)
1
3
5
2
4
110Ω
R
R
130Ω
Detection
circuit
Module mounting screw
(FG)
AUX.
4
2
3
1
5
4
2
3
1
Communication
circuit
Detection
circuit
UNIT POWER
LINK IN
4
2
3
1
Detection
circuit
LINK OUT
AJ65FBTA42-16DTE
Constant
voltage
circuit
LINK IN
Detection
circuit
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
AJ65FBTA42-16DT
Pin no.
+24V
Y9
Vacant
Y8
Vacant
+24V
YB
Vacant
YA
Vacant
+24V
YD
Vacant
YC
Vacant
+24V
YF
Vacant
YE
Vacant
LINK IN
Male
2
3
1
4
LINK OUT
Female
2
1
4 53
Pin no.
1
2
3
4
5
Pin no.
1
2
3
4
5
Pin no.
UNIT POWER/AUX.
Male
X0
—
X1
1
2
3 54
X2
—
X3
I/O
Female
2
1
4 53
Front view
X4
—
X5
X6
—
X7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Communication connector
LINK IN
SLD
DB
DG
DA
No pin
Power supply connector
UNIT POWER
+24V (UNIT)
Vacant
24G (UNIT)
Vacant
FG
I/O connector
Pin no.
Pin no.
+24V
X1
Y8
—
24G
Y9
X0
Vacant
+24V
X3
YA
—
24G
YB
X2
Vacant
+24V
X5
YC
—
24G
YD
X4
Vacant
+24V
X7
YE
—
24G
YF
X6
Vacant
Mitsubishi Electric Automation
|
LINK OUT
SLD
DB
DG
DA
Vacant
AUX.
+24V (I/O)
Vacant
24G (I/O)
Vacant
FG
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Pin no.
Vacant
Y9
24G
Y8
Vacant
Vacant
YB
24G
YA
Vacant
Vacant
YD
24G
YC
Vacant
Vacant
YF
24G
YE
Vacant
Distributed I/O 363
AJ65SBTW4-16D
Sink input
Source input
LINK
CABL
LINK
CABL
DA
DB
DG
SLD
+24V
FG
24G
1
2
3
4
5
6
7
Isolation
DC/DC
Common for module
POWER
power supply
CABL
and I/O power supply
Four wire type sensor (sink output)
Sink
Sink/source
selector switch
R
R
Source
Module mounting screw
CON1
4
2
1
3
R
R
R
CON8
4
2
1
3
R
Detection
circuit
CON2
4
2
1
3
R
Two wire type sensor (sink output)
Detection
circuit
Detection
circuit
Detection
circuit
LINK
CABL
Four wire type sensor
(sink output/sink input)
Detection
circuit
Sink
Sink/source
selector switch
R
R
R
R
R
CON2
4
2
1
3
R
CON8
4
2
1
3
R
R
R
AJ65SBTW4-16DT
Common for module
power supply and I/O power supply
Isolation
DC/DC
Three wire type sensor (sink output)
Three wire type sensor (sink output)
Two wire type sensor (sink output)
DA
DB
DG
SLD
+24V
FG
24G
Source
Module mounting screw
CON1
4
2
1
3
Detection
circuit
Detection
circuit
Common for module
POWER
power supply
CABL
and I/O power supply
Four wire type sensor (sink output)
1
2
3
4
5
6
7
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
POWER
CABL
Pin layout
Isolation
1
2
3
4
DC/DC
Constant
voltage circuit
Module
mounting screw
CON1
4
2
1
3
R
R
AJ65SBTW4-16D
Three wire type sensor
(sink output)
Detection
circuit
364
CON8
4
2
1
3
AJ65SBTW4-16DT
Pin No.
Signal name
Pin No.
Signal name
1
+24V
1
+24V
2
X8~XF
2
Y8~YF
3
24G
3
24G
4
X0~X7
4
X0~X7
R
R
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
External Connections
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CC-Link Remote I/O: AJ65SBTCFo-o • AJ65VBTCFo-o • AJ65BTCo-o
FCN Connector Type
n All I/O wiring terminates in a single 40 pin connector.
n Connectors available separately to facilitate wiring harness construction.
n All models UL • cUL listed and CE certified.
• FCN connector
Performance Specifications
Number of
Input Points
Isolation
Method
Rated Input
Voltage
ON Voltage
OFF Voltage
Input
Response Time
External
Connection
Wire Type
Common
Connection
Internal
Current
Consumption
DC input (sink/source common type)
32 points
Photocoupler
24 VDC
14 V min.
6 V max.
1.5 ms max.
One wire type
32 points
1 common
45mA
DC input (sink, source type)
32 points
Photocoupler
24 VDC
14 V min.
6 V max.
10 ms max.
One wire type
32 points
1 common
70mA
Input Module
Model Name
Input Type
AJ65SBTCF1-32D
AJ65BTC1-32D
Output Module
Model Name
Output Type
AJ65SBTCF1-32T
Transistor output (sink type)
Transistor output (sink type)
AJ65BTC1-32T
Number
of Output
Points
Isolation
Method
Rated
Load
Voltage
32 points
Photocoupler
12/24 VDC
32 points
Photocoupler
AJ65SBTCF1-32DT
DC input
/ transistor output
Sink, source type
/ sink type
Number
Isolation
of I/O
Method
Points
16 points Photocoupler
/photocoupler
/16 points
AJ65VBTCF1-32DT1
DC input
/ transistor output
Sink, source type
/ sink type
16 points Photocoupler
/16 points
/photocoupler
I/O Module
Model Name
I/O Type
12/24 VDC
Operating Voltage
Maximum Load Current
Output Response Time
1 Point
1 Common
0.1A
3.2A
0.1A
2A
24 VDC
24 VDC
Internal
Current
Consumption
ON—OFF
Surge
Suppression
0.5 ms
max.
0.5 ms
max.
1.5 ms
max.
2 ms
max.
Zener
diode
One wire type
32 points
1 common
60mA
Clamp
diode
One wire type
32 points
1 common
115mA
Maximum Load Operating Voltage
Input
Output Response Time
Current
Response 1
1
ON
OFF
OFF—ON
ON—OFF
Time
Point Common Voltage Voltage
14 V
6V
0.5 ms
1.5 ms
12/24
1.5ms 0.1A 0.8A
min.
max.
max.
max.
VDC
15
V
3
V
0.5
ms
1.5 ms
12/24
0.2ms 0.1A 1.6A
min.
max.
max.
max.
VDC
Rated Voltage
Input
External
Common
Connection
OFF—ON
Load
Connection
Wire Type
External
Surge
Connection Wire
Suppression Type on Input
/Output Sides
Zener
One wire type
diode
Zener
diode
One wire type
Common
Connection
Internal
Current
Consumption
16 points 1 common
/16 points 1 common
50mA
16 points 1 common
/16 points 1 common
50mA
Module Features
AJ65SBTCF1-32
Transmission speed
setting switch
Operation LED display
Setting value
Transmission speed
Item checked
0
156 kbps
PW
Turns on when the power supply to the remote I/O
module is turned on.
1
625 kbps
2
2.5 Mbps
L RUN
Turns on when normal data is received from the master
station, and turns off via timeout.
3
5.0 Mbps
4
10 Mbps
LED name
STATION NO.
B RATE
40 20 10 8 4 2 1 4 2 1
X0-XF
L ERR
X0 to 1F
Y0 to 1F
Turns on in case of a transmission error (CRC error)
and turns off via timeout (L RUN also turns off). It
turns on if the settings for station number and transmission speed are wrong. It flashes if the stationnumber and transmission-speed settings are
changed while the communication is active.
ON
MITSUBISHI
A J65SBTCF1-32D
X10-X1F
X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F NC NC NC NC
X0
X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC NC COM COM
Station number
setting switches
"10," "20," and "40" in STATION NO. are used for
setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for
setting the first digit of the station number.
Displays the on/off status of input. The LEDs turn on
in the "On" state, and off in the "Off" state.
Input/output display
selector switch
Terminal block
Connector
The compact remote I/O module power supply, transmission, and I/O signals are connected here.
Connector for input/output signals
DIN rail hook
Hook for mounting the module to the DIN rail
Mitsubishi Electric Automation
|
Distributed I/O 365
AJ65VBTCF1-32DT1
Transmission speed
setting switch
Setting value
Transmission speed
0
156 kbps
1
625 kbps
2
2.5 Mbps
3
5.0 Mbps
4
10 Mbps
Transmission speed
setting
LED nameswitch
40 S
T
20 A
10 T
I
8 O
4 N
2 N
1 O
4 B
2 R
A
T
1 E
PW
L RUN
L ERR
Station number
setting switches
A J65VBTCF1-32DT1
"10," "20," and "40" in STATION NO. are
used for setting the second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are
used for setting the first digit of the station
number.
LINK
CON.A
CON.B
X0
Y10
XF
Y1F
X0 to F
PW
Y10 to 1F
L RUN
Item checked
Turns on when the power supply to the remote I/O module is turned on.
Turns on when normal data is received from
the master station, and turns off via timeout.
Turns on in case of a transmission error
(CRC error) and turns off via
timeout (L RUN also turns off). It turns on if
the settings for station number and transmission speed are wrong. It flashes if the station-number and transmission-speed settings are changed while the communication
is active.
Displays the on/off status of input. The
LEDs turn on in the "On" state, and off in
the "Off" state.
L ERR
One-touch connector
for communication
Input/output display selector switch
DIN rail hook
8
9
A
B
C
D
E
F
PW/AUX.
CON.C
DIN rail hook
0
1
2
3
4
5
6
7
CON.D
One-touch connector
for power supply and FG
Connector
Connector for input/output signals
* Side view shows connectors fitted.
AJ65BTC1-32
Operation LED display
LED name
PW
L RUN
L ERR
0 to F
Transmission speed setting switch
Item checked
Setting value
Transmission speed
Turns on when the power supply to the remote I/O module is turned on.
0
156 kbps
1
625 kbps
Turns on when normal data is received from
the master station, and turns off via timeout.
2
2.5 Mbps
3
5.0 Mbps
4
10 Mbps
Turns on in case of a transmission error
(CRC error) and turns off via
timeout (L RUN also turns off). It turns on if
the settings for station number and transmission speed are wrong. It flashes if the station-number and transmission-speed settings are changed while the communication
is active.
Station number setting switches
"10," "20," and "40" in STATION NO. are used for setting the
second digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for setting the
first digit of the station number.
Displays the on/off status of input. The
LEDs turn on in the "On" state, and off in
the "Off" state.
MITSUBISHI
A J65BTC1-32D
B RATE
0 1
PW
L RUN
SD
RD
2
3
L ERR.
4
0
1
2
3
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
4
5
6
7
8
9
A
B
C
D
E
F
STATION NO.
X10
X1
0 1
9 0 1
2
2 8
3
3 7
6 5 4
6 5 4
A
0
B
1
3
DA
+24V
DG
4
2
DB
7
5
24G
6
SLD
(FG)
Terminal block
Connector
DIN rail hook
The compact remote I/O module power supply, transmission,
and I/O signals are connected here.
Connector for input/output signals
Hook for mounting the module to the DIN rail
* Side view shows connectors fitted.
366
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Module Features
External Dimensions
AJ65VBTCF1-32o
AJ65SBTCF1-32o
41
Unit: mm
67
46
CON.B
X0
Y10
XF
Y1F
PW
L RUN
L ERR
CON.D
STATION NO.
B RATE
40 20 10 8 4 2 1 4 2 1
X0-XF
16.5
8
9
A
B
C
D
E
F
PW/AUX.
CON.C
118
109 +10 (mounting pitch)
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
ON
MITSUBISHI
A J65SBTCF1-32D
X10-X1F
20
11
0
1
2
3
4
5
6
7
115
approximate
110°
110
110°
50
X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F NC NC NC NC
X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC NC COM COM
7.9
16.5
4
31
External Connections
Combination Input / Output Module
AJ65BTC1-32o
46
9.5
AJ65SBTCF1-32DT1
1
2
3
4
5
LINK CABLE
(IN)
Two ø4.5mm mounting holes
MITSUBISHI
1
2
3
4
5
LINK CABLE
(OUT)
A J65BTC1-32D
0 1
PW
L RUN
SD
RD
2
3
L ERR.
4
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
B
+24V
4
2
DB
UNIT POWER CABLE (IN)
7
5
DG
24G
6
SLD
(FG)
I/O POWER CABLE (IN)
156
165
UNIT POWER
CABLE (OUT)
I/O POWER
CABLE (OUT)
1
2
3
4
5
1
2
3
4
5
CON.C
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 NC
5 NC
CON.D
1 FG
2 +24V(UNIT)
3 24G(UNIT)
4 NC
5 NC
Isolation
DC/DC
One-touch connector
for power supply and FG
CON1
B20, A20
R
R
3
DA
B13, A13
R
R
1
CON.A
DA
DB
DG
NC
SLD
CON.B
1 DA
2 DB
3 DG
4 NC
5 SLD
1
2
3
4
5
One-touch connector
for communication
65
0
A
STATION NO.
X10
X1
0 1
9 0 1
2 8
2
3 7
3
6 5 4
6 5 4
56
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CON.A
40
A J65VBTCF1-32DT1
LINK
B12, A12
I/O power supply
L
L
CON1
B10, A10
B3, A3
B1, A1
I/O power supply
(external power supply)
B2, A2
Constant
voltage circuit
L
B3, A3
B1, A1
B2, A2
In case I/O power supply
and load power supply are common
Mitsubishi Electric Automation
|
Distributed I/O 367
Input Module
Combination Input / Output Module
AJ65SBTCF1-32D type
AJ65SBTCF1-32DT type
Module power
supply
I/O power
supply
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
B2
B1
X0
X1
X2
X3
X4
X5
X6
X7
X8
X9
XA
XB
XC
XD
XE
XF
X10
X11
X12
X13
X14
X15
X16
X17
X18
X19
X1A
X1B
X1C
X1D
X1E
X1F
COM
COM
1
2
3
4
5
6
7
Isolation
Module power
supply
DC/DC
B20
B19
B18
B17
B16
B15
B14
B13
A20
A19
A18
A17
A16
A15
A14
A13
A,B12
A,B11
B10
B9
B8
B7
B6
B5
B4
B3
A10
A9
A8
A7
A6
A5
A4
A3
A,B1
A,B2
R
R
I/O power
supply
I/O power supply
(external power
supply)
R
DA
DB
DG
SLD
+24V
FG
24G
L
L
X0
X1
X2
X3
X4
X5
X6
X7
X8
X9
XA
XB
XC
XD
XE
XF
COM
NC
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y1A
Y1B
Y1C
Y1D
Y1E
Y1F
CTL+
COM-
R
R
R
A3 Y1F
A,B1 CTL+
A,B2 COM-
In case I/O power supply
and load power supply are common
Output Module
Input Module
AJ65SBTCF1-32T type
AJ65BTC1-32D type
Module power
supply
L
L
1
2
3
4
5
6
7
DA
DB
DG
SLD
+24V
FG
24G
B20
B19
B18
B17
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
B1,2
A1,2
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
YA
YB
YC
YD
YE
YF
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y1A
Y1B
Y1C
Y1D
Y1E
Y1F
CTL+
COM
Isolation
1
2
3
4
5
6
7
DC/DC
DC24V
DA
DB
DG
SLD
+24V
FG
24G
B20~B5
DC/DC
R
R
A20~A5
R
R
DC24V
B1,B2
Constant
voltage
circuit
Load power supply
In case I/O power supply
and load power supply are common
L
R
Constant
voltage circuit
R
L
I/O power supply
(external power
supply)
Isolation
DC/DC
Output Module
AJ65BTC1-32T type
B1,2 CTL+
A1,2 COM
1
2
3
4
5
6
7
DC24V
DA
DB
DG
SLD
+24V
FG
24G
L
L
B20~5
R
A20~5
R
B1,B2
DC12/24V
368
DC/DC
A1,A2
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
External Connections
CC-Link Remote I/O: AJ65VBTSx-n
n n n & AJ65VBTCEn
n-n
n n n Spring Clamp & e-CON Type
These I/O blocks enable cost savings through reduced labor & material costs. Spring clamps eliminate the need for wiring lugs and avoid the need
for periodic retightening of I/O terminals. The e-CON terminals use the same I/O connection type as the existing CC-Link/LT I/O blocks. UL and
cUL listing and CE certifications on most units.
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Performance Specifications
Input Module
Model Name
Input Type
Number Of
Input
Points
Isolation
Method
Rated Input
Voltage
Operating Voltage
On Voltage Off Voltage
Input Response Time
OFF-ON
External Connection
Wire Type
Common Connection
Wire Gauge Size
Internal Current Consumption
ON-OFF
AJ65VBTS3-16D
DC input
+COM
16
Photocoupler
24VDC
14VDC min 6VDC max 1.5ms max 1.5ms max
Three wire type
16 points 1 common
AWG 28 to 16
35mA
AJ65VBTS3-32D
DC input
+COM
32
Photocoupler
24VDC
14VDC min 6VDC max 1.5ms max 1.5ms max
Three wire type
16 points 1 common
AWG 28 to 16
40mA
Number of
Output
Points
Isolation
Method
Output Module
Model Name
Output Type
Rated Load Maximum Load Current Output Response Time
Voltage
1 Point 1 Common OFF-ON
ON-OFF
Leakage
Current
Surge
External Connection
Common Connection
Suppression
Wire Type
Wire Gauge Size
Internal Current
Consumption
AJ65VBTS2-16T
Transistor
Sink
16
Photocoupler
12/24VDC
0.5A
4A
1ms max
1ms max
0.1mA max
Zener diode
Two wire type
16 points 1 common
AWG 28 to 16
45mA
AJ65VBTS2-32T
Transistor
Sink
32
Photocoupler
12/24VDC
0.5A
4A
1ms max
1ms max
0.1mA max
Zener diode
Two wire type
16 points 1 common
AWG 28 to 16
60mA
Number of
I/O Points
Isolation
Method
Input/Load
Voltage
Input
Response
Time
24VDC/
24VDC
1.5ms max
0.5A
4A
14VDC min
24VDC/
24VDC or
12VDC
1.5ms max
0.5A
4A
14VDC min
Combined I/O
Module Model
Name
I/O Type
Maximum Output Load
Current
1 Point
AJ65VBTS32-16DT
DC input/
transistor
output
+COM/sink
8/8
Photocoupler/
photocoupler
AJ65VBTS32-32DT
DC input/
transistor
output
+COM/sink
16/16
Photocoupler/
photocoupler
Input Module Model
Name
Input Type
Input Operating Voltage
1 Common On Voltage Off Voltage
Operating Voltage
Number Of
Input
Points
Isolation Method
Output Response Time
Leakage
Current
Connection
Surge
Wire Type On Common
SuppresInput/ Output Connection
sion
Sides
Internal Current
Consumption
OFF-ON
ON-OFF
6VDC max
1ms max
1ms max
0.1mA
max
Zener
diode
Three wire
type / Two
wire type
16 points/
common
15mA
6VDC max
1ms max
1ms max
0.1mA
max
Zener
diode
Three wire
type / Two
wire type
16 points/
common
50mA
Input Response Time
Rated Input Voltage
On Voltage Off Voltage
OFF-ON
ON-OFF
External Connection
Wire Type
Common Connection
Internal Current Consumption
AJ65VBTCE3-8D
DC input
+COM
8
Photocoupler
24VDC
14VDC min 6VDC max
1.5ms max
1.5ms max
Three wire type
8 points 1 common
35mA
AJ65VBTCE3-16D
DC input
+COM
16
Photocoupler
24VDC
14VDC min 6VDC max
1.5ms max
1.5ms max
Three wire type
16 points 1 common
35mA
Leakage
Current
Surge
Suppression
External Connection
Wire Type
Common Connection
Internal Current Consumption
0.1mA max
Zener diode
Two wire type
8 points 1 common
35mA
Output Module
Model Name
AJ65VBTCE2-8T
Combined I/O
Module Model
Name
AJ65VBTCE3216DT
Output Type
Transistor
Isolation
Method
8
Photocoupler
Sink
I/O Type
DC input/
transistor
output
Number Of
Output
Points
Number Of
I/O Points
+COM/sink
8/8
Isolation
Method
Photocoupler/
photocoupler
Rated Load Maximum Load Current Output Response Time
Voltage
1 Point 1 Common OFF-ON
ON-OFF
12/24VDC
Input/Load
Voltage
24VDC/
24VDC
0.1A
0.8A
1ms max
Maximum Output
Load Current
Input
Response
Time
1 Point
1.5ms max
0.1A
1ms max
Input Operating Voltage
1 Common On Voltage Off Voltage
0.8A
14VDC min
6VDC max
Output Response Time
OFF-ON
ON-OFF
1ms max
1ms max
Leakage
Current
0.1mA
max
Connection
Surge
Wire Type on Common
SuppresInput/Output Connection
sion
Sides
Zener
diode
Three wire
type / Two
wire type
16 points/
common
Internal Current
Consumption
40mA
External Dimensions
Mitsubishi Electric Automation
|
Distributed I/O 369
Input Module
AJ65VBTS3-32D
Input Module
AJ65VBTS3-16D
n DISTRIBUTED I/O
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
370
External Connections
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Input Module
AJ65VBTCE3-8D
Input Module
AJ65VBTCE3-16D
Mitsubishi Electric Automation
|
Distributed I/O 371
Output Module
AJ65VBTS2-32T
n DISTRIBUTED I/O
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
372
Output Module
AJ65VBTS2-16T
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Output Module
AJ65VBTCE2-8T
Output Module
AJ65VBTCE2-16T
Mitsubishi Electric Automation
|
Distributed I/O 373
Combination Input/Output Module
AJ65VBTS32-32DT
n DISTRIBUTED I/O
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
374
Combination Input /Output Module
AJ65VBTS32-16DT
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Combination Input/Output Module
AJ65VBTCE32-16DT
Mitsubishi Electric Automation
|
Distributed I/O 375
n Compatible with CC-Link Version V2.0.
n Eight analog channels occupy only one station, instead of three with CC-Link V1.10.
n High precision analog to digital conversion.
n Switchable input ranges for each channel.
n Sampling or averaging processing.
n One touch connectors reduce installation time and cost (available separately).
n Module can be replaced without disrupting the network (when “on line” network connector is used.)
n All models UL and cUL listed and CE certified.
Performance Specifications
Model Name
Analog Input
AJ65VBTCU-68ADVN
Voltage
Current
Digital Value
Input/Output
Characteristics
*Accuracy
(Accuracy Relative to the
Maximum Digital Output Value)
External Connection
Method
One-Touch Connector
for Communication
Applicable One-touch Connector
for Power Supply
Wire Size
One-Touch Connector
for Analog I/O
Module Mounting Screws
or Applicable Metal Fittings
Applicable DIN Rail
External Power Supply
Inrush Current
Internal Current Consumption (24 VDC)
Weight
External Dimensions
376
—
0 to 20 mA DC (input resistance 250 )
12 bit + sign (-4096 to +4095)
Analog input range
AJ65VBTCU-68ADV
Voltage
AJ65VBTCU-68ADI
Current
Input Range Switching
Offset/Gain Setting
Maximum Conversion Speed
Absolute Maximum Input
Number of Analog Input Points
Station Type
Number of Occupied Stations,
Expanded Cyclic Setting
CC-Link-Compatible Function
Withstand Voltage
Isolation Method
AJ65VBTCU-68ADIN
-10 to + 10 VDC (input resistance 1 m )
—
12-bit + sign (-4096 to +4095)
Digital value
-10 to +10V
User range setting 1 (-10 to +10 V)
0 to 5 V
1 to 5 V
User range setting 2 (-10 to +10 V)
0 to 20 mA
4 to 20 mA
User range setting (0 to 20 mA)
Accuracy
Ambient temperature
Ambient temperature
0 to 55 ˚C
25 ± 5 ˚C
-4000 to +4000
Maximum
resolution
2.5mV
0 to 4000
(
%
± 0.3
± 12digit
*)
(
%
*)
± 0.2
± 8digit
0 to 4000
1.25mV
1.0mV
1.25mV
5µA
4µA
5µA
For each channel
Yes
1 ms/channel
Voltage: ±30 mA
8 channels/module
Remote device station
Ver. 1 mode: 3 stations (RWr/RWw 12 words each, RS/RY 32 points)
Ver. 2 mode: 1 station (extended word (RWr/RWw) 16 words each, RX/RY 32 points), Quadruple
Cyclic transmission, extended cyclic transmission, station-to-station cable length relaxation
Between batch of power supply/communication systems and batch of analog inputs: 500 VAC for one minute
Between communication system and batch of analog inputs: Photocoupler isolation / Between power supply system and batch of analog inputs: Photocoupler isolation
Between channels: No isolation / Communication interface: No isolation
One-touch connector for communication [transmission circuit] (5-pin/solderless type. The connector plug is sold separately.)
One-touch connector for power supply and FG [module power supply and FG] (5-pin/solderless type. The connector plug is sold separately.)
One-touch connector for analog input (4-pin/solderless type. The connector plug is sold separately.)
(Optional parts) Online connector for communication: A6CON-LJ5P, online connector for power supply: A6CON-PWJ5P
Voltage: ±15 V
Communication line: CC-Link dedicated cable compatible with Ver.1.10, 0.5 mm (AWG20) [ø2.2 to 3.3 mm]
Shielded power supply 0.5 mm (AWG20)
2
2
2
0.66 to 0.98 mm (AWG18) [ø2.2 to 3.0 mm], wire size 0.08 mm or more
2
ø1.0 to 1.4 mm (A6CON-P214), ø1.4 to 2.0 mm (A6CON-P220), [applicable wire size: 0.14 to 0.2 mm ]
ø1.0 to 1.4 mm (A6CON-P514), ø1.4 to 2.0 mm (A6CON-P520), [applicable wire size: 0.3 to 0.3 mm ]
2
2
A6PLT-J65VI
TH35-7.5Fe, TH35-7.5Al (compliant to JIS C 2812)
24 VDC(20.4 to 26.4 VDC with a ripple rate of 5% or less)
4.2 A, 1.2 ms max.
0.10A
0.17kg
41(W) x 115(H) x 67(D)
* 1 digit refers
to one digital unit.
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Analog Modules: AJ65VBTCU-68ADVN • AJ65VBTCU-68ADIN
FCN Connector Type
Module Features
SELECT/SET switch
Connector for communication
Connector pin no.
Operating condition LED display
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
54321
Description
POWER
On: When the power supply is turned
Normal mode
On: Normal operation
On: When the SELECT/SET
Pin no.
5
4
3
2
1
Name
SLD
NC
DG
DB
DA
switch is in the SET position
RUN
Test mode
Off: When the SELECT/SET
switch is in the SELECT
Connector for analog I/O
L RUN
or central position
On: When the communication is normal
L ERR.
Off: When the communication is normal
LED display for offset/gain adjustment
Connector pin no.
4321
Transmission speed setting switch
Setting value
Transmission speed
0
156kbps
1
625kbps
Pin no.
4
3
2
1
2
2.5Mbps
Name
SLD
NC
V-/I-
V+/I+
3
5.0Mbps
4
10Mbps
Station number setting switch
"10," "20," and "40" in STATION NO. are used for setting the second
digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for setting the first digit
of the station number.
Connector for power supply
Connector pin no.
54321
Mode selector switch
Description
AJ65VBTCU-68ADVN/68ADIN
Pin no.
5
4
3
2
1
Name
FGI
AG
Module -24V
Module +24V
FG
Ver.1mode
0: Normal mode
1: Test mode
(user range setting 1)
2: Test mode
(user range setting 2)
For a detailed description of the connectors,
see introduction to CC-Link section
External Connections
AJ65UBTCU-68AIN
Ver.2 mode
Ver.1mode
Ver.2 mode
3: Normal mode
4: Test mode
(user range setting 1)
5: Test mode
(user range setting 2)
6 to 7: Not used
0: Normal mode
1: Test mode
(user range setting 1)
3: Normal mode
4: Test mode
(user range setting 1)
2,5∼7: Not used
External Dimensions
Unit: mm
AJ65VBTCU-68ADVN (in case of voltage input)
Signal source: 0 to ±10V
*3
CH1
1 V+
2 V3 NC
+15V
500k
500k
4 SLD
GND
-15V
*1 Shield
AJ65VBTCU-68ADVN (in case of current input)
Signal source 0 to ±20mA
2
CH8
500k
1 I+
2 I3 NC
250k
500k
4 SLD
*1
Shield
AG
*4
GND
Rated plate
FG1
*1 For wire, use two-core shielded twisted-pair cable.
*2 Note the input resistance of AJ65VBTCU-68ADI.
*3 Connect a capacitor of around 0.1 to 0.47 µF (it must be a product that can
withstand voltages of 25 V or more) between the V and COM terminals if
noise or ripple is generated in the external wiring.
*4 Be sure to ground FG1. There are cases where AG should also be grounded if the signal is particularly noisy.
The offset or gain value should be set again if the ground wiring is changed
after setting the offset or gain value (whether the signals were connected to
ground or not).
Mitsubishi Electric Automation
|
Distributed I/O 377
AJ65SBT-64AD Analog Input
n Four channels (voltage input / current input).
n Switchable input ranges.
n Handles analog ranges ±10 VDC and 0 ~ 20mA.
n Compact size.
n Perform channel averaging without affecting conversion speed.
n Certification: UL • cUL • CE
AJ65BT-64AD Analog Input
n Four channels (voltage input / current input).
n Handles analog ranges ±10 VDC and 0 ~ 20mA.
n Certification: UL • cUL • CE
Performance Specifications
Model Name
AJ65SBT-64AD
AJ65BT-64AD
Voltage
-10 to +10 VDC (input resistance 1M )
Current
0 to 20 mA DC (input resistance 250 )
-20 to +20 mA DC (input resistance 250 )
12 bit + sign (-4096 to +4095)
12 bit or 11 bit + sign (0 to 4000, or -2000 to +2000
Digital Value
Input/Output
Analog input range
Digital value
Maximum
Characteristics
-4000 to +4000
0 to 5 V
1.25mV
1 to 5 V
0 to 4000
Current
0 to 20mA
1.0mV
±0.4%
1.25mV
(±16 digit*)
0 to 4000
4µA
0 to +20 mA (user range setting 3)
2.5mV
0 to 5 V
-2000 to +2000
1.25mV
to 20 mA
1mV
±1%
20µA
(±40 digit*)
0 to 20mA
0 to +4000,or
10µA
0 to 20mA
-2000 to +2000
5µA
4µA
Yes
1 ms/channel
Voltage: ±15 V, current: ±30 mA
4 channels/module
Remote device station
1 station (32 points each for RX/RY, 4 words each for RWr/RWw)
2 stations (32 points each for RX/RY, 8 words each for RWr/RWw)
Between batch of power supply/communication systems and batch of analog inputs: 500 VAC for one minute
Withstand Voltage
Between power supply system and batch of analog inputs: Photocoupler isolation/Between communication system and batch of analog inputs: Photocoupler isolation/Between channels: No isolation
7-point 2-piece terminal block (transmission, power supply), directly mounted 18-point terminal block (analog output area)
27-point terminal block (M3.5)
0.3 to 0.75 mm2
0.75 to 2.00 mm2
M4 x 0.7 mm x 16 mm or more, possible to mount on a DIN rail
Module Mounting Screws
TH35-7.5Fe, TH35-7.5Al (compliant to JIS C 2812)
TH35-7.5Fe, TH35-7.5Al, TH35-15Fe (compliant to JIS C 2812)
Applicable Solderless Terminal
RAV1.25 to 3.5 (compliant to JIS C 2805)
RAV1.25 to 3.5, RAV2 to 3.5
Internal Current Consump. (24 VDC)
0.09A
0.12A
Weight
0.20kg
0.35kg
118(W) x 50(H) x 40(D)mm
151.9(W) x 65(H) x 63(D)mm
External Dimensions
Note: 1 digit refers to one bit.
378
5mV
0 to +4000,or
All channels in the batch
Station Type
Applicable DIN Rail
to +10 V
For each channel
Number of Analog Input Points
Applicable Wire Size
Ambient temperature 0 to 55°C
4 to 20mA
Absolute Maximum Input
Isolation Method
Accuracy
resolution
0 to +10 V
-20
5µA
Maximum Conversion Speed
External Connection Method
Maximum
1 to 5 V
±0.2%
(±8 digit*)
5µA
4 to 20mA
Digital value
Voltage/current
-10
2.5mV
Offset/Gain Setting
Number of Occupied Stations
Analog input range
Voltage
-10 to +10 V
-10 to +10 V (user range setting 1)
0 to +5 V (user range setting 2)
Input Range Switching
Accuracy
resolution Ambient temperature 0 to 55° Ambient temperature 25± 5°
Voltage
*Accuracy
(Accuracy Relative
to the Maximum
Digital Output Value)
-10 to +10 VDC (input resistance 1M )
Current
Analog Input
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Analog Modules: AJ65SBT-64AD • AJ65BT-64AD
Analog to Digital Converter Modules
AJ65SBT-64AD Module Features
Station number setting switches
Operating condition LED display
LED name
Normal
mode
L RUN
On: When the communication
is normal
PW
On: Normal operation
L RUN L ERR.
CH1 2
3
4
MITSUBISHI
OFFSET GAIN
A J65SBT-64AD
DA DG +24V
DB
SLD
On: When the transmission speed
or station number setting is outside
the range
L ERR.
RUN
24G
(FG)
SELECT
B RATE
4 2 1
ON
SET
CH1
CH2
CH3
CH4
V+
I+
AG
TEST
V+
I+
COM SLD COM
I+
TEST COM
V+
SLD COM
V+
I+
(FG1)
LED display
for offset/gain adjustment
CHo
OFFSET
GAIN
40
OFF
OFF
OFF
OFF
:
OFF
OFF
:
ON
Unit-digit
20
OFF
OFF
OFF
OFF
:
OFF
OFF
:
ON
10
OFF
OFF
OFF
OFF
:
ON
ON
:
OFF
8
OFF
OFF
OFF
OFF
:
OFF
OFF
:
OFF
4
OFF
OFF
OFF
OFF
:
OFF
OFF
:
ON
2
OFF
ON
ON
OFF
:
OFF
OFF
:
OFF
1
ON
OFF
ON
OFF
:
OFF
ON
:
OFF
Transmission speed
setting switches
Normal
Always off
mode
Setting switch
Setting
value
Terminal block
0
1
2
3
4
DIN rail hook
The compact remote I/O module power
supply, transmission, and I/O signals are
connected here.
SELECT/SET switch
4
OFF
OFF
OFF
OFF
ON
2
OFF
OFF
ON
ON
OFF
Transmission
speed
1
OFF
ON
OFF
ON
OFF
156 kbps
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
AJ65BT-64AD Module Features
Station number setting switches
GAIN switch
Transmission speed setting switch
RESET switch
Transmission speed
0
1
2
3
4
Other than
0 to 4
156 kbps (factory setting)
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
Not used (L ERR. LED turns on
and a communication error occurs.)
Analog input range
setting pins
C
D
MITSUBISHI
MELSEC A
B RATE
J65BT-64AD
0 1
RD
L ERR.
4
CH.
OFFSET
GAIN
DA DG +24V
DB
SLD
A J65SBT-64AD
24G
(FG)
L RUN LED
On: When the communication is normal
SD LED
Turns on during data transmission
RD LED
Turns on during data reception
L ERR. LED
On: Communication data error
3
5
OFFSET switch
4
DB
7
+24V
DG
2
9
11
CH1
V+
24G
6
SLD
8
(FG)
TEST
10
TEST
(4.5)
B RATE
4 2 1
ON
15
CH2
V+
COM
14
SLD
17
COM
16
CH2
I+
19
CH3
I+
18
CH3
V+
21
SLD
20
COM
23
CH4
I+
22
CH4
V+
25
27
SLD
24
FG1
26
COM
AG
Unit: mm
B RATE STATION NO.
X10
X1
0 1
PW
STATION NO.
40 20 10
8 4 2 1
13
12
CH1
I+
Two ø4.5mm
mounting holes
40
AJ65BT 64RD
SELECT
On: Normal operation
AJ65BT-64AD External Dimensions
Unit: mm
SW
0
1-4
16.5
OFFSET GAIN
Normal
mode
9
MODE
NORMAL
TEST CH.
TEST
RUN
L RUN
SD
RD
4
0 1
2
3
6 5 4
9 0 1
2
3
8
7
MODE OFFSET
9 0 1
L ERR.
4
6 5 4
2
3
UP
RESET
SET
2
3
GAIN
DOWN
SET
CH1
CH2
CH3
CH4
V+
I+
AG
TEST
V+
I+
COM SLD COM
I+
TEST COM
V+
SLD COM
V+
I+
(FG1)
50
MITSUBISHI
4
RUNLED
Terminal block
Two 4.5 mm x 5.1 mm mounting holes
(for M4 mounting screws)
3
On: When the power supply is turned
on
DA
109
CH1 2
Item checked
PW LED
1
118
L RUN L ERR.
LED name
2
3
Channel selector switch
AJ65SBT-64AD External Dimensions
RUN
RESET
1
A
B
* Use D when 0 to 20 mA is used.
PW
Operating condition
LED display
4
The analog input range is set as follows:
Voltage
Current
0~10V
(0~20mA)*
A
1~5V
4~20mA
B
-10~10V
-20~20mA
C
0~5V
0~20mA
D
(4.5)
2
3
PW
RUN
L RUN
SD
STATION NO.
X10
X1
0 1
9 0 1
2
2 8
3
3 7
6 5 4
6 5 4
56
65
Setting
number
142.9
151.9
9.5
63
4
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
RUN
STATION NO.
40 20 10
8 4 2 1
10-digit
Station
no.
1
2
3
4
:
10
11
:
64
Item checked
On: When the power supply is turned
on
PW
AJ65SBT-64AD/ AJ65BT-64AD External Connection Diagram
In case of voltage input
Signal source: 0 to ± 10V
＊4
Signal source: 0 to ± 10V
CH1
V＋
I＋
COM
SLD
＋15V
500KΩ
*1
500KΩ
*2
Indicates the input resistance of AJ65SBT-64AD and AJ65BT-64AD, respectively.
*3
Connect a capacitor of around 0.1 to 0.47 µF (it must be a product that can withstand voltag -
*4
Be sure to ground FG1. There are cases where AG should also be grounded if the signal is particularly noisy.
The offset or gain value should be set again if the ground wiring is changed after setting the offset or gain value
(whether the signals were connected to ground or not).
ー15V
＊1 Shield
＊2
In case of current input
Signal source: 0 to ± 20mA
CH4
V＋
＊3
I＋
COM
SLD
Signal source: 0 to ± 20mA
＊1 Shield
＊5
For wiring, use two-core shielded twisted-pair cable.
250Ω
es of 25 V or more) between the V and COM terminals if noise or ripple is generated in the external wiring.
GND
500KΩ
250Ω
500KΩ
AG
FG1
Mitsubishi Electric Automation
|
Distributed I/O 379
n Compatible with CC-Link V2.0.
n Eight analog channels occupy only one station, instead of three with CC-Link V1.10.
n High precision analog to digital conversion.
n Switchable output ranges for each channel.
n Clear or retain analog output when the controller stops.
n One-touch connectors reduce installation time and cost (available separately).
n Module can be replaced without disrupting the network (when “on-line” network connector is used.)
n Certification: UL • cUL • CE
Performance Specifications
AJ65VBTCU-68DAVN
12 bit + sign (-4096 to +4095)
-10 to + 10 VDC (external load resistance: 2 k to 1 M )
Model Name
Digital Value
Analog Output
Input/Output Characteristics
*Accuracy
(Accuracy Relative to the Maximum
Analog Output Value)
Digital
Analog
-4000 to +4000
-10 to +10 V
User range setting 1
(-10 to +10 V)
0 to 5 V
1 to 5 V
User range setting 2
(0 to 5 V)
Voltage
0 to 4000
Output Range Switching
Offset/Gain Setting
Maximum Conversion Speed
Output Short-Circuit Protection
Absolute Maximum Output
Number of Analog Output Points
Station Type
Number of Occupied Stations,
Expanded Cyclic Setting
CC-Link-Compatible Function
Isolation Method
External Connection Method
One-Touch Connector
for Communication
Applicable
Wire Size
One-Touch Connector
for Power Supply
One-Touch Connector
for Analog I/O
Applicable DIN Rail
External Power Supply
Inrush Current
Internal Current Consumption
Weight
External Dimensions
380
Accuracy
Ambient temperature
Ambient temperature
0 to 55 °C
25 ±5 °C
±0.3%
(±30 mV)
±0.2%
(±20 mV)
±0.3%
(±15 mV)
±0.2%
(±10 mV)
Maximum
resolution
2.5mV
1.25mV
1.0mV
1.25mV
For each channel
Yes
1 ms/channel
Yes
±12V
8 channels/module
Remote device station
Ver. 1 mode: 3 stations (RWr/RWw 12 words each, RS/RY 32 points)
Ver. 2 mode: 1 station (extended word (RWr/RWw) 16 words each, RX/RY 32 points), Quadruple
Cyclic transmission, extended cyclic transmission, station-to-station cable length relaxation
Between communication system and batch of analog outputs: Photocoupler isolation
Between power supply system and batch of analog outputs: Photocoupler isolation
Between channels: No isolation
One-touch connector for communication [transmission circuit] (5-pin/solderless type. The connector plug is sold separately.)
One-touch connector for power supply and FG [module power supply and FG] (5-pin/solderless type. The connector plug is sold separately.)
One-touch connector for analog input (4-pin/solderless type. The connector plug is sold separately.)
(Optional parts) Online connector for communication: A6CON-LJ5P, online connector for power supply: A6CON-PWJ5P
Communication line: CC-Link dedicated cable compatible with Ver.1.10, 0.5 mm2 (AWG20) [ ø 2.2 to 3.3 mm]
Shielded power supply 0.5 mm2 (AWG20)
2
2
0.66 to 0.98 mm (AWG18) [ ø 2.2 to 3.0 mm], wire size 0.08 mm or more
ø1.0 to 1.4 mm (A6CON-P214), ø1.4 to 2.0 mm (A6CON-P220), [applicable wire size: 0.14 to 0.2 mm2 ]
ø1.0 to 1.4 mm (A6CON-P514), ø1.4 to 2.0 mm (A6CON-P520), [applicable wire size: 0.3 to 0.3 mm2 ]
TH35-7.5Fe, TH35-7.5Al (compliant to JIS C 2812)
Metal fitting for CC-Link connector type: A6PLT-J65V1
24 VDC (20.4 to 26.4 VDC with a ripple rate of 5% or less)
4.3 A, 1.2 ms max.
0.15A
0.16kg
41(W) x 115(H) x 63(D)
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Analog I/O Modules: AJ65VBTCU-68DAVN
Digital To Analog Converter Module
Module Features
SELECT/SET switch
Connector for communication
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Connector pin no.
Operating condition LED display
54321
Description
POWER
Pin no.
5
4
3
2
1
Name
SLD
NC
DG
DB
DA
On: When the SELECT/SET
switch is in the SET position
Off: When the SELECT/SET
switch is in the SELECT
or central position
On: When the communication is normal
Off: When the communication is normal
RUN
Test mode
L RUN
L ERR.
Connector for analog I/O
On: When the power supply is turned on
Normal mode
On: Normal operation
LED display for offset/gain adjustment
Connector pin no.
4321
Transmission speed setting switch
Setting value
Transmission speed
0
156kbps
1
625kbps
Pin no.
4
3
2
1
2
2.5Mbps
Name
SLD
NC
V-/I-
V+/I+
3
5.0Mbps
4
10Mbps
Station number setting switch
"10," "20," and "40" in STATION NO. are used for setting the second
digit of the station number.
"1," "2," "4," and "8" in STATION NO. are used for setting the first digit
of the station number.
Connector for power supply
Connector pin no.
54321
Mode selector switch
Description
AJ65VBTCU-68DAVN
Pin no.
5
4
3
2
1
Name
FGI
AG
Module -24V
Module +24V
FG
Ver.1mode
0: Normal mode
1: Test mode
(user range setting 1)
2: Test mode
(user range setting 2)
* For a detailed description of the connectors,
see introduction to CC-Link section.
External Connection
External Dimensions
*1
D/A
conversion
*2
1
2
3
4
Unit: mm
Motor drive module, etc.
CH1
V+
NC
COM
NC
Ver.2 mode
3: Normal mode
4: Test mode
(user range setting 1)
5: Test mode
(user range setting 2)
6 to 7: Not used
2k
1k
GND
Motor drive module, etc.
CH8
V+
NC
COM
NC
1
2
3
4
2k
1k
GND
Rated plate
*1 For wire, use two-core shielded twisted-pair cable.
*2 Connect a capacitor of around 0.1 to 0.47 µF (it must be a product that can
withstand voltages of 25 V or more) between the V and COM terminals if noise
or ripple is generated in the external wiring.
Mitsubishi Electric Automation
|
Distributed I/O 381
AJ65SBT-64AD Analog Input
n Two channels (voltage input / current input)
n Handles analog ranges ±10 VDC and 0 ~ 20mA
n Switchable analog outputs
n Compact size
n Certification: UL • cUL • CE
AJ65BT-64DAV
n Four channels (voltage output)
n Handles analog ranges ±10 VDC and 0 ~ 20mA
n Certification: UL • cUL • CE
AJ65BT-64DAI
n Four channels (current output).
n Digital values from 0 to +4000 can be converted to analog values of 4 mA to +20 mA
n Certification: UL • cUL • CE
Performance Specifications
Model Name
Digital
Voltage
Value
Current
Analog
Voltage
Output
Current
12 bit (0 to 4095)
-10 to + 10 VDC (external load resistance: 2 k to 1 M )
0 to 20 mA DC (external load resistance: 0 to 600 )
Analog
Output
Maximum
Resolution
- 4000 to +4000
-10 to +10 V
2.5mV
- 4000 to +4000
-10 to +10 V (user range setting 1)
2.5mV
0 to 4000
0 to 5 V
1.25mV
0 to 4000
1 to 5 V
1.0mV
0 to 4000
0 to 5 V (user range setting 2)
1.25mV
0 to 4000
0 to 20 mA
5µA
0 to 4000
4 to 20 mA
4µA
Current
Voltage
Digital
Value
0 to 20 mA (user range setting 3)
4 to 20 mA DC (external load resistance: 0 to 600 )
Accuracy
Ambient Temperature
Ambient Temperature
0 to 55°C
25 ±5 °C
±0.4%
±0.2%
5µA
(±40mV)
(±20mV)
±0.4%
±0.2%
(±20mV)
(±10mV)
±0.4%
±0.2%
(±80µA)
(±40µA)
Digital
Value
Analog
Output
+2000
+10V
+1000
+5V
0
±0
-1000
-5V
-2000
-10V
Maximum
Resolution
5mV
Accuracy
(Overall)
Digital
Value
Analog
Output
4000
+20mA
2000
+12mA
0
+4mA
Maximum
Resolution
±1
4µA
None
Yes
Max. Conversion Speed
1 ms/channel
No. of Analog Output Points
2 channels/module
4 channels/module
No. of Occupied Stations
1 station (32 points each for RX/RY, 4 words each for RWr/RWw)
2 stations (32 points each for RX/RY, 8 words each for RWr/RWw)
7-point 2-piece terminal block (transmission, power supply),
directly mounted 18-point terminal block (analog output area), M3 screws
17-point terminal block, M3.5 screws
0.3 to 0.75 mm2
0.75 to 2.00 mm2
Connection Terminal Block
Applicable Wire Size
Module Mounting Screws
Applicable DIN Rail
Applicable Solderless Term.
M4 x 0.7 mm x 16 mm or more, possible to mount on a DIN rail
TH35-7.5Fe, TH35-7.5Al (compliant to JIS C 2812)
TH35-7.5Fe, TH35-7.5Al, TH35-15Fe (compliant to JIS C 2812)
RAV1.25 to 3.5 (compliant to JIS C 2805)
RAV1.25 to 3.5, RAV2 to 3.5
Internal Current
Consumption (24 VDC)
0.16A
Weight
0.2kg
0.2kg
118(W) x 50(H) x 40(D) mm
151.9(W) x 65(H) x 63(D)mm
External Dimensions
0.18 A
±1
(±200mA)
Yes
Output Short-Circuit Protect.
Accuracy
(Overall)
(±0 mV)
For each channel
Offset/Gain Setting
382
AJ65BT-64DAI
12 bit (0 to +4095)
0 to 4000
Output Range Switching
AJ65BT-64DAV
11 bit + sign ( - 2048 to +2047)
-10 to + 10 VDC (external load resistance: 2 k to 1 M )
Input/Output
Characteristics
*Accuracy
(Accuracy Relative
to the Maximum
Analog Output Value)
AJ65SBT-62DA
12 bit + sign ( - 4096 to +4095)
0.27A
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Analog Modules: AJ65SBT-62DA • AJ65SBT-64DAV • AJ65SBT-64DAI
Digital To Analog Converter Module
AJ65SBT-62DA Module Features
Station number setting switches
Operating condition LED display
Item checked
Station
no.
PW
On: When the power supply is turned
on
RUN
Normal
mode
L RUN
On: When the communication is
normal
1
2
3
4
:
10
11
:
64
PW
RUN
L RUN L ERR.
CH1 2
OFFSET GAIN
MITSUBISHI
A J65SBT-62DA
DA DG +24V
DB
SLD
24G
(FG)
UP
SET
DOWN
B RATE
4 2 1
CH1
ON
CH2
TEST
NC
V+
I+
NC
V+
I+
NC
NC
TEST
NC COM
NC
NC
COM NC
NC
NC
On: When the transmission speed or
station number setting is outside the
range
SELECT/SET switch
Terminal block
DIN rail hook
The compact remote I/O module power supply, transmission, and I/O signals are connected here.
Hook for mounting the module to the DIN rail
External Connections
8
OFF
OFF
OFF
OFF
:
OFF
OFF
:
OFF
4
2
1
OFF OFF ON
OFF ON OFF
OFF ON ON
ON OFF OFF
:
:
:
OFF ON OFF
OFF ON ON
:
:
:
ON OFF OFF
0
1
2
3
4
Transmission
speed
156 kbps
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
External Dimensions
In case of current output
Motor power supply
module, etc.
CH1
Unit: mm
Motor power supply
module, etc.
~
D/A電源
0
V+
COM
1M
GND
118
109
(4.5)
*2
CH1
2k
V+
COM
*1
600
GND
PW
Motor power supply
module, etc.
CH2
Motor power supply
module, etc.
CH2
2k
L RUN L ERR.
CH1 2
OFFSET GAIN
SELECT
UP
STATION NO.
40 20 10
8 4 2 1
B RATE
4 2 1
ON
SET DOWN
A J65SBT-62DA
24G
(FG)
CH1
CH2
NC
V+
I+
NC
V+
I+
NC
NC
TEST
TEST
NC COM
NC
NC
COM NC
NC NC
~
COM
1M
GND
RUN
MITSUBISHI
DA DG +24V
DB
SLD
0
V+
~
V+
COM
40
(4.5)
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
~
*2
*1
16.5
In case of voltage output
600
GND
For wire, use two-core shielded twisted-pair cable.
Connect a capacitor of around 0.1 to 0.47 µF (it must be a product that can withstand voltages of 25 V or more) to the
input terminals of an external device if noise or ripple is generated in the external wiring.
4
*1
*2
10
OFF
OFF
OFF
OFF
:
ON
ON
:
OFF
Setting switch
4
2
1
OFF
OFF OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF OFF
Setting
value
Normal
Always off
mode
D/A
power
supply
Unit-digit
20
OFF
OFF
OFF
OFF
:
OFF
OFF
:
ON
Transmission speed setting switches
LED display for offset
/gain adjustment
CHo
OFFSET
GAIN
10-digit
40
OFF
OFF
OFF
OFF
:
OFF
OFF
:
ON
50
L ERR.
STATION NO.
40 20 10
8 4 2 1
SELECT
On: Normal operation
AJ65BT-64DAV/DAI Module Features
Station number setting switch
Station number setting switches
Transmission speed setting switch
Setting number
0
1
2
3
4
LED name
Transmission speed
156 kbps (factory setting)
625 kbps
2.5 Mbps
5.0 Mbps
10 Mbps
MITSUBISHI
MELSEC A
B RATE
J65BT-64DAV
0 1
2
3
PW
RUN
L RUN
SD
RD
L ERR.
4
CH.
STATION NO.
X10
X1
0 1
9 0 1
2
2 8
3
3 7
6 5 4
6 5 4
OFFSET
UP
1
2
3
4
SET
GAIN
Item checked
PW
On: When the power supply is turned
on
RUN
Normal
mode
L RUN
On: When the communication is
normal
SD
Turns on during data transmission
RESET
DOWN
On: Normal operation
Terminal block
RD
Turns on during data reception
AJ65BT-64DAV
L ERR.
On: When the baud rate or station
number setting is outside the range
1
3
DA
2
5
DG
4
DB
7
+24V
6
SLD
24G
8
(FG)
9
11
13
15
17
19
21
23
25
27
HLD/ HLD/
CH1/
CH2
CH3
CH4
CLR
CLR
V+
V+
V+
V+
10
12
14
16
18
20
22
24
26
TEST
COM
TEST
COM
COM
COM
AJ65BT-64DAI
1
3
DA
2
5
DG
4
DB
7
+24V
6
SLD
24G
8
(FG)
RESET (reset switch)
9
11
13
15
17
19
21
23
25
27
HLD/ HLD/
CH1/
CH2
CH3
CH4
CLR
CLR
I+
I+
I+
I+
10
12
14
16
18
20
22
24
26
TEST
COM
TEST
COM
COM
COM
CH. (CHANNEL) selector switch
HLD/CLR setting terminal
HOLD is set by short-circuiting the terminals, while CLEAR is set by having no connection between them.
OFFSET/GAIN
UP/DOWN switch
External Dimensions
External Connections
Unit: mm
AJ65BT-64DAI
Motor drive module, etc.
2k
1M
GND
*1
CH1
Motor drive module, etc.
*2
14
Two ø4.5mm mounting holes
0
15
B RATE STATION NO.
X10
X1
AJ65BT64DAV
600
GND
0 1
PW
RUN
L RUN
SD
RD
4
0 1
2
3
6 5 4
4
2k
1M
GND
2
3
UP
RESET
SET
DOWN
Motor drive module, etc.
CH4
0
27
26
~
CH4
26
6 5 4
2
3
GAIN
25
8
7
MODE OFFSET
9 0 1
L ERR.
Motor drive module, etc.
9 0 1
2
3
56
65
14
*2
~
*1
CH1
13
~
AJ65BT-64DAV
~
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
LED name
600
GND
142.9
151.9
63
*1: For wiring, use two-core shielded twisted-pair cable.
*2: Connect a capacitor of around 0.1 to 0.47 µF 25V to the input terminals of an external device if noise or ripple is generated in the external wiring.
Mitsubishi Electric Automation
|
Distributed I/O 383
AJ65BT-68TD
n Eight thermocouple inputs per module.
n Compatible with K, E, J, T, B, R and S thermocouples.
n Assign any thermocouple type to each channel.
n Enable/disable conversion for each channel.
n Disconnection detection.
n Select either sampling or moving average processing
for each channel.
n Automatic cold junction compensation for PT100 RTD.
n Certification: UL • cUL • CE
AJ65BT-64RD3 / 64RD4
n Four RTD inputs per module.
n Enable/disable conversion for each channel.
n Disconnection detection.
n Offers moving average processing to reduce effects of noise.
n Accurate to ±0.25% of full scale measurement.
n Certification: UL • cUL • CE
Performance Specifications
Model name
AJ65BT-68TD
AJ65BT-64RD3
Temperature Input Range
Temperature Detection Value
Scaling Value
Overall Accuracy
Cold-Junction Compensation System (°C)
Resolution (°C)
Conversion Speed (Sampling Time: ms/ch)
Temperature Sensor Input Channel
B, R, S, K, E, J, T
-200 to 1700 °C
-180 to 600 °C
16-bit signed binary
( -2000 to 17000: Value up to the first decimal place x 10)
16-bit signed binary ( -800 to 6000: Value up to the first decimal place x 10)
32-bit signed binary ( -80000 to 600000: Value up to the third decimal place x 1000)
16-bit signed binary (0 to 2000)
*1
Isolation Method
Applicable Solderless Terminal
±0.1% (accuracy relative to the maximum value)
±0.25% (accuracy relative to the maximum value)
±1.0
0.025°C
40 ms/channel
4 channels/module
8 channels + 1 channel for connecting the Pt100 sensor
Remote device station
4 stations (128 points each for RX/RY, 16 words each for RWr/RWw)
Between thermocouple input and CC-Link transmission system
Between platinum resistance temperature sensor input and CC-Link transmission system
and between channels: Transformer isolation
: Photo-coupler isolation / Between channels: No isolation
RAV1.25 to 3.5 (compliant to JIS C 2805)
RAV1.25 to 3.5, RAV2 to 3.5 (compliant to JIS C 2805)
27-point terminal block (M3.5 x 7 screws)
Connection Terminal Block
1ms
Allowable Momentary Power Failure Period
0.75 to 2.00 mm2
Applicable Wire Size
Module Mounting Screws
M4 x 0.7 mm x 16 mm or more, possible to mount on a DIN rail
Applicable DIN Rail
TH35-7.5Fe, TH35-7.5Al, TH35-15Fe (compliant to JIS C 2812)
24 VDC (18 to 30 VDC)
External Power Supply
Internal Current Consumption (24 VDC)
0.081A
0.17A
Weight
0.40kg
0.38kg
External Dimensions
*1 The calculation method of overall accuracy is as shown below:
(Overall accuracy) + (Conversion accuracy) x (Temperature characteristic) + (Operating ambient temperature change) + (Cold-junction compensation accuracy)
Here, the operating ambient temperature change denotes a value not within the operating ambient temperature range of 25±5°C.
384
Ambient temperature (20 ˚C or less, 30 ˚C or more)
Ambient temperature (20 ˚C or less, 30 ˚C or more)
B, R, S , 0.3°C K, E, J, T : 0.1°C
45 ms/channel
Station Type
Number of Occupied Stations
Four wire type
Pt100, JPt100
Connectable Platinum Resistance Temp. Sensors
Connectable Thermocouples
AJ65BT-64RD4
Three wire type
Measurement Method
151.9(W) x 65(H) x 63(D) mm
Example: In the case of the overall accuracy with operating thermocouple of K,
measured temperature of 150°C, and operating ambient temperature of 35°C, the following applies:
(±0.5°C) + (±0.06°C) x (5°C) + (±1°C) = ±1.8°C
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Analog Modules: AJ65BT-68TD • AJ65BT-64RD3 • AJ65BT-64RD4
Temperature Input Modules
AJ65BT-68TD Module Features
Station setting switches
Operating condition LED display
Setting number
0
1
2
3
4
Other than
0 to 4
LED name
Transmission speed
156 kbps (factory setting)
625 kbps
2.5 Mbps
5 Mbps
10 Mbps
Not used (If other than 0 to 4 is set, L ERR. LED
turns on and a communication error occurs.)
MITSUBISHI
MELSEC
B RATE
A J65BT-68TD
SW
0
MODE
NORMAL
1∼8 TEST CH.
9
TEST
PW
RUN
L RUN
SD
RD
L ERR.
0 1
4
2
3
MODE
8
7
9 0 1
6 5 4
STATION NO.
X10
X1
0
9 0 1
1
2
2 8
3
3 7
6 5 4
6 5 4
OFFSET
UP
RESET
GAIN
Select this when ending the test mode and entering
normal operation (factory setting)
These settings select a channel for which errors are
1 to 8 TEST CH. compensated for in the test mode.
Select TEST to compensate for errors. The test mode
9
TEST
is entered after 2 seconds.
0
Item checked
PW LED
On: When the power supply is turned
on
RUNLED
Normal
mode
L RUN LED
On: When thecommunication
is normal
SET
2
3
DOWN
Mode setting switch
Turns on during data transmission
RD LED
Turns on during data reception
L ERR. LED
On: Communication data error
(CRC error)
SET
Terminal
block
1
3
DA
2
5
DG
7
+24V
4
DB
9
CH1+
11
CH2+
13
CH3+
15
CH4+
17
CH5+
19
CH6+
21
CH7+
23
CH8+
25
RTD
27
RTD
24G
6
SLD
8
CH1-
10
CH2-
12
CH3-
14
CH4-
16
CH5-
18
CH6
20
CH7-
Reset switch
Offset/gain setting switch
OFFSET
GAIN
22
CH8-
24
On: Normal operation
SD LED
NORMAL
Compensation mode of the offset value
Compensation mode of the gain value
The temperature detection value when the OFFSET/GAIN
switch is placed in the SET position, is stored in the internal
memory of AJ65BT-68TD as the offset/gain value.
UP/DOWN switch
Pt100 resistance temperature sensor
Resistance temperature sensor for measuring terminal
block temperature (attached to the module)
26
(FG)
External Connections
External Dimensions
Amplifier
input
SW
0
1∼8
9
CH8
Transformer
Filter
＋
ー
65.0
MODE
NORMAL
TEST CH.
TEST
*1 Make sure to use shielded compensating
conductor cable.
*2 Make sure to ground.
1
2
STATION NO.
X10
X1
0 1
9 0 1
2
2 8
3
3 7
6 5 4
6 5 4
B RATE
A J65BT-68TD
Transformer
Filter
Amplifier
input
＋
ー
MELSEC
PW
RUN
L RUN
SD
RD
L ERR.
0 1
4
2
3
MODE
9 0
8
7
1
6 5 4
OFFSET
UP
RESET
SET
2
3
GAIN
DOWN
65.0
MITSUBISHI
CH1
Unit: mm
Two ø4.5mm mounting holes
56.0
RTD
Pt100
Amplifier
input
142.9
63
151.9
AJ65BT-64RD3/RD4 Module Features
Transmission speed setting switch
Setting number
0
1
2
3
4
Other than
0 to 4
Station setting switches
Transmission speed
156 kbps (factory setting)
625 kbps
2.5 Mbps
5 Mbps
10 Mbps
Not used (If other than 0 to 4 is set, L ERR. LED
turns on and a communication error occurs.)
MITSUBISHI
MELSEC
Mode setting switch
0
1~8
9
B RATE
A J65BT-64RD
SW
0
1∼4
9
MODE
NORMAL
TEST CH.
TEST
PW
RUN
L RUN
SD
RD
L ERR.
0 1
4
MODE
9 0 1
4
2
3
Pins for specifying the platinum
resistance temperature sensor type
STATION NO.
X10
X1
0 1
9 0 1
2
2 8
3
3 7
6 5 4
6 5 4
UP
OFFSET
When a Pt100 sensor
is connected
Circuit
board
2
3
GAIN
PW LED
RUNLED
L RUN LED
SD LED
1
AJ65BT-64RD3
3
DA
2
5
DG
4
DB
7
+24V
6
SLD
9
(FG)
11
A1
24G
8
10
NC
13
b1
12
B1
15
SLD
14
SLD
17
A2
16
NC
19
b2
18
B2
21
A3
20
NC
23
b3
22
B3
25
SLD
24
SLD
27
A4
26
NC
b4
B4
1
3
DA
2
5
DG
4
DB
7
+24V
6
SLD
9
(FG)
11
A1
10
24G
8
a1
13
b1
12
B1
15
SLD
14
SLD
17
A2
16
a2
19
b2
18
B2
21
A3
20
a3
B3
23
b3
22
25
SLD
24
RD LED
Turns on during data reception
OFFSET
GAIN
L ERR. LED
On: Communication data error (CRC
error)
SLD
27
A4
26
a4
Item checked
On: When the power supply is turned
on
Normal On: Normal operation
mode
On: When thecommunication is normal
Turns on during data transmission
Offset/gain setting switch
SET
AJ65BT-64RD4
Circuit
board
Station setting switches
DOWN
LED name
Terminal block
When a JPt100 sensor
is connected
RESET
SET
Select this when ending the test mode and entering
NORMAL normal operation (factory setting)
These settings select a channel for which errors are
TEST CH. compensated for in the test mode.
Select
TEST to compensate for errors. The test mode
TEST
is entered after 2 seconds.
b4
Compensation mode of the offset value
Compensation mode of the gain value
The temperature detection value when the OFFSET/GAIN
switch is placed in the SET position, is stored in the internal
memory of AJ65BT-68TD as the offset/gain value.
Reset switch
B4
UP/DOWN switch
External Connections
The highest accuracy can be obtained for AJ65BT64RD4 by using 4-conductor type platinum resistance
temperature sensors.
Example of connecting a 4-conductor type platinum
resistance temperature sensor
Two ø4.5mm mounting holes
CH1
Internal circuit
SLD
Shield
a1
A1
B1
b1
SLD
Constant
voltage circuit
Internal circuit
MITSUBISHI
CH1
Unit: mm
External Dimensions
MELSEC
B RATE
A J65BT-64RD4
SW MODE
0
NORMAL
1∼4 TEST CH.
9
TEST
0
PW
RUN
L RUN
SD
RD
L ERR.
1
2
3
4
MODE
9 0 1
4
STATION NO.
X10
X1
0 1
9 0 1
2 8
2
3 7
3
6 5 4
6 5 4
OFFSET
UP
RESET
SET
2
3
GAIN
DOWN
65
AJ65BT-64RD4
The highest accuracy can be obtained for AJ65BT64RD3 by using 3-conductor type platinum resistance
temperature sensors.
Example of connecting a 3-conductor type platinum
resistance temperature sensor
56
AJ65BT-64RD3
Shield
GND
SLD
1
a4
A4
B4
b4
SLD
GND
1
GND
Internal circuit
CH4
CH4
Internal circuit
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Transmission speed setting switch
142.9
151.9
63
*1: According to the operating environment, it may be better to connect in some cases.
Mitsubishi Electric Automation
|
Distributed I/O 385
AJ65BT-D62
n DC input/sink output type.
n Preset DC input.
n Maximum counting speed: 200 kpps.
AJ65BT-D62/D62D/D62D-S1
n 24 bit counter.
n 5/12/24 VDC (2 to 5 mA input).
n Switchable counting speed.
n Four counter functions:
• Latch-counter function
• Sampling counter function
• Periodic pulse-counter function
• Count-disable function
AJ65BT-D62D
n Differential input/sink output type.
n Preset DC input.
n Maximum counting speed: 400 kpps.
AJ65BT-D62D-S1
n Differential input/sink output type.
n Preset differential input.
n Maximum counting speed: 400 kpps.
* Certification: UL • CUL • CE
Performance Specifications
Model Name
Counting Speed Selector Switch Setting
Number of channels
Phase
Count
Input
Signal Level
Signal
(øA, øB)
Counting
Speed
(Maximum)
AJ65BT-D62
AJ65BT-D62D
HIGH side
HIGH side
LOW side
LOW side
5/12/24 VDC, 2 to 5 mA
1 Phase
Input
200kpps
10kpps
400kpps
10kpps
400kpps
10kpps
2 Phase
Input
200kpps
7kpps
300kpps
7kpps
300kpps
7kpps
Counter
24-bit binary 0 to 16777215
Preset up/down counter and ring counter functions
5µs
Minimum Count
Pulse Width
2.5µs
100µs
2.5µs
(1 and 2 phase input)
142µs
50 50
µs µs
71 71
µs µs
(1 phase input)
(2 phase input)
*1
*1
Coincidence Comparison Range
Output
Comparison Result
2.5µs
1.25 1.25
µs µs
(1 phase input)
3.3µs
1.65 1.65
µs µs
(2 phase input)
*2
100µs
50 50
µs µs
(1 phase input)
142µs
2.5˜µs
71 71
µs µs
1.25 1.25
µs µs
(2 phase input)
*2
(1 phase input)
24-bit binary
Setting value < count value, setting value = count value, setting value > count value
5/12/24 VDC, 2 to 5 mA
Preset
Function Start
Response Time
Coincidence Output
Response Time
External
Output
Station Type
Number of Occupied Stations
Power Supply Voltage
Current Consumption (at 24 VDC)
Connection Terminal Block
Applicable Wire Size
Applicable Solderless Terminal
Allowable Momentary Power Failure Period
Module Mounting Screws
Applicable DIN Rail
Weight
70mA
0.41kg
*1 The rise and fall time of the input signal should be 2 µs or less and have a duty cycle of 50%.
*2 The rise and fall time of the input signal should be 0.1 µs or less and have a duty cycle of 50%.
386
HIGH side
2 channels
1 phase input, 2 phase input
EIA standard, RS-422-A differential type line driver level
[Equivalent to Am26L31 (Japan Texas Instruments, Inc)]
Counting Range
Model
External
Input
AJ65BT-D62D-S1
LOW side
5/12/24 VDC, 2 to 5 mA
OFF—ON : 0.5 ms max., ON—OFF : 3 ms max.
2A/1 common
0.1 ms max.
Remote device station
4 stations
18 to 28.8 VDC
100mA
27-point terminal block (M3.5 x 7 screws)
0.75 to 2.00 mm2
RAV1.25 to 3.5, RAV2 to 3.5 (compliant to JIS C 2805)
1ms
M4 x 0.7 mm x 16 mm or more, possible to mount on a DIN rail
TH35-7.5Fe, TH35-7.5Al, TH35-15Fe (compliant to JIS C 2812)
3.3µs
100µs
1.65 1.65
µs µs
50 50
µs µs
(2 phase input)
*2
(1 phase input)
71 71
µs µs
(2 phase input)
*2
EIA standard, RS-422-A differential type line driver level
[Equivalent to Am26L31 (Japan Texas Instruments, Inc)]
5/12/24 VDC, 2 to 5 mA
120mA
0.42kg
142µs
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link High-Speed Counter Modules
AJ65BT-D62 • AJ65BT-D62D • AJ65BT-D62D-S1
Transmission speed setting switch
Station number setting switches
This is used for setting the transmission speed of the highspeed counter module (for data link).
The station number of the high-speed counter module should
be set within the range from 1 to 61.
"X10" is used for setting the ten-digit of the station number.
"X1" is used for setting the unit-digit of the station number.
Setting number
0
1
2
3
4
Transmission speed
156 kbps (factory setting)
625 kbps
2.5 Mbps
5 Mbps
10 Mbps
Other than
0 to 4
Not used (If other than 0 to 4 is set, L
ERR. LED turns on and a communication error occurs.)
MITSUBISHI
MELSEC A
CH.2
øA
øB
DEC
PRE
F ST.
EQU1
EQU2
CH.1
øA
øB
DEC
PRE
F ST.
EQU1
EQU2
B RATE
STATION NO.
X10
X1
0 1
0 1
90 1
2
2 8
2
3
3 7
3
4 654
654
RING
PLS
RESET
CH. 1 2
CH. 1 2
ON LOW
J65BT-D62
PW
RUN
L RUN
SD
RD
L ERR.
LED display
LED name
HIGH
LED display
Item checked
Turns on when voltage is applied to the phase A
pulse input terminal.
Terminal block
1
DEC
Turns on when the counter value is decremented.
PRE
Turns on and remains on when voltage is applied to the
RESET terminal.
Turns off when the external preset detection reset
command signal is asserted.
F ST.
3
5
7
9
11
13
15
17
19
21
23
25
On: When the power supply is turned on
RUN
On: Normal operation
L RUN
On: When the communication is normal
SD
Turns on during data transmission
RD
Turns on during data reception
L ERR.
On: Communication data error
Mode switch
27
Ring counter setting switch
2
4
6
8
10
12
14
16
18
20
22
24
This is used to set whether to enable or disable the ringcounter function.
26
Reset switch
Pulse input setting pin (same for CH.2)
AJ65BT-D62
Circuit
board
Turns on when voltage is applied to the F.START
terminal.
EQU1
Turns on when the counter value is equal to coincidence output setting No. 1.
EQU2
Turns on when the counter value is equal to coincidence output setting No. 2. (Not available in
AJ65BT-D62D-S1)
AJ65BT-D62D
CH.1
øB
øA
AJ65BT-D62D-S1
CH.1
Jumper
F ST.
(When the jumper is connected to 12 V)
(When the jumper is connected to 5 V)
CH.1
F ST.
PRE
F ST.
PRE
24V
12V
5V
Turns on when voltage is applied to the phase B
pulse input terminal.
Item checked
PW
24V
12V
5V
øB
24V
12V
5V
LED name
øA
24V
12V
5V
(When the jumper is connected to 24 V)
External Connections
Example of connection with a pulse generator
(24 VDC) of open-collector output type
AJ65BT-D62
510 1/3W
Example of connection with a pulse generator
(5 VDC) of voltage-output type
AJ65BT-D62
510 1/3W
Pulse input voltage setting pin ＊
*
Pulse generator
4.7K 1/3W
Pulse input voltage setting pin*
4.7K 1/3W
øA
4.7K 1/3W
øA
4.7K 1/3W
OUT
OUT
Twisted shielded cable
Twisted shielded cable
øA
+24V
GND
E
Shield
510 1/3W
øA
E
510 1/3W
Pulse input voltage setting pin ＊
*
4.7K 1/3W
Pulse input voltage setting pin*
4.7K 1/3W
øB
4.7K 1/3W
øB
4.7K 1/3W
OUT
OUT
Twisted shielded cable
Twisted shielded cable
+24V
øB
E
+24V
DC24V
External
power
supply
0V
0V
Remark: *Set the pulse input voltage setting pin to the
GND
E
Shield
External
power
supply
øB
position.
DC+5V
DC24V
0V
0V
Remark: *Set the pulse input voltage setting pin to the
position.
AJ65BT-D62D-S1
Example of connection with a line driver pulse generator
(equivalent to Am26L31)
AJ65BT-D62D
Pulse generator
Twisted shielded cable
A
A
A
Pulse generator
A
E
Twisted shielded cable
A
A
A
A
Twisted shielded cable
E
Twisted shielded cable
PRESET
Z
B
Am26LS32
Z
14050
E
External
power
supply
B
Am26LS32
B
B
B
B
14050
E
B
Twisted shielded cable
B
VCC
VCC
GND
GND
Am26LS32
External
power
supply
PRESET
E
VCC
VCC
GND
GND
External Dimensions
Direction of view A
Unit: mm
STATION NO.
X10
X1
0 1
90 1
2 8
2
3 7
3
4
654
654
RESET
RING
PLS
CH. 1 2
CH. 1 2
ON LOW
CH.2
φB
φA
FST
PRE
FST
PRE
63
HIGH
CH.1
φB
φA
24V
12V
5V
PW
RUN
L RUN
SD
RD
L ERR.
2
3
24V
12V
5V
0 1
9.5
B RATE
J65BT-D62
CH.2
øA
øB
DEC
PRE
F ST.
EQU1
EQU2
24V
12V
5V
MELSEC A
24V
12V
5V
CH.1
øA
øB
DEC
PRE
F ST.
EQU1
EQU2
56
MITSUBISHI
65
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Module Features
Rated plate
Two ø4.5mm
mounting holes
142.9
Direction of view A
151.9
Mitsubishi Electric Automation
|
Distributed I/O 387
n Decentralized motion control — can be placed anywhere on a CC-Link network.
n Supports absolute positioning with Mitsubishi’s intelligent digital servo line.
n Differential driver supports pulse output to 400 kpps and 10M distance to amplifiers.
n A wide selection of positioning control functions including:
• Seven types of home position return functions
• Automatic trapezoid and S curve acceleration/deceleration methods
n Point table for each axis (up to 600 points).
n Certification: UL • cUL • CE
Performance Specifications
Item
Item
Specification
Number of Control Axes
Interpolation Function
Control Method
2 axes
2-axis linear interpolation, 2-axis circular interpolation *1
mm, inch, degree, pulse
Positioning Data
It is possible to set 600 data points (positioning data No.: 1 to 600) per axis
Positioning
interpolation can be set), speed control, speed/position switch control
Windows version 75P
A7HGP /SW1RX-AD75P or later
PC-9800 series /SW1NX-AD75P or later
*2
Starting Time
DOS/V PC (IBM PC/AT compatible PC) /SW1IVD-AD75P or later *3
Teaching Module
AD75TU (software version D or later)
Backup
Parameters and positioning data are stored in the flash memory (battery-less).
Speed/position switch control: Increment/absolute systemr
It is possible to switch between 1 to 65535 (ms) and 1 to 8388608 (ms)
It is possible to set 4 patterns for both acceleration and deceleration times.
It is possible to switch between 1 to 65535 (ms) and 1 to 8388908 (ms)
(same ranges as for the acceleration/deceleration time)
20 ms or less (excluding link scan time)
10136-3000VE (soldering-type, accessory)
Applicable Wire Size
In case of 10138-3000VE: AWG#2 to #30 (approximately 0.05 to 0.2 SQ)
In case of 10138-6000VE: AWG#28 (approximately 0.08 SQ)
Absolute system
Positioning
Connector
*4
Locus control: Increment/absolute system
Maximum Output Pulse
When connected to differential driver: 400 kbps
When connected to open collector: 200 kbps
When connected to differential driver: 10 m
• -214748364.8 to 214748364.7 (µm)/ -13421772.8 to 13421772.7 (µm) *5
Maximum Connection
Distance Between Servos
• -21474.83648 to 21474.83647 (inch)/ -1342.17728 to 1342.17727 (inch)
Station type
Intelligent device station
• 0 to 359.99999 (degree)/0 to 359.99999 (degree)
Number of Occupied Stations 4 stations (128 points each for RX/RY, 16 words each for RWr/RWw)
• 2147483648 to 2147483647 (pulse)/ -134217728 to 134217727 (pulse)
External Power Supply
Increment system
When connected to open collector: 2 m
24 VDC (20.4 to 26.4 V)
Applicable Wire Size
0.75 to 2.00 mm2
Module Mounting Screws
M4 x 0.7 mm x 16 mm or more, possible to mount on a DIN rail
• -21474.83648 to 21474.83647 (inch)/ -1342.17728 to 1342.17727 (inch)
Applicable DIN Rail
TH35-7.5Fe, TH35-7.5Al, TH35-15Fe (compliant to JIS C 2812)
• -21474.83648 to 21474.8364.7 (degree)/ -1342.17728 to 1342.17727 (degree)
Applicable Solderless Terminal RAV1.25 to 3.5, RAV2 to 3.5
• -2147483648 to 2147483647 (pulse)/ -134217728 to 134217727 (pulse)
24 VDC Internal
Current Consumption
0.30A
• 0 to 214748364.7 (µm)/0 to 13421772.7 (µm)
External Dimensions
170(W) x 63.5(H) x 80(D) mm
• 0 to 21474.83647 (inch)/0 to 1342.17727 (inch)
Weight
0.50kg
• -214748364.8 to 214748364.7 (µm)/ -13421772.8 to 13421772.7 (µm)
Positioning
Range
and S-curve acceleration/deceleration *6
10136-6000EL (pressure connection type, sold separately)
PTP control: Increment/absolute system
Positioning
Method
Acceleration
/Deceleration
Time
Rapid-Stop
Deceleration
Time
GX Configurator-AP
/Software Package
Automatic trapezoid acceleration/deceleration
PTP (Point to Point) control, locus control (both linear and circular
Control Unit
Peripheral Device
Specification
Acceleration
/Deceleration
Processing
Speed/position switch control (increment system)
• 0 to 21474.83647 (degree)/0 to 1342.17727 (degree)
• 0 to 2147483647 (pulse)/0 to 134217727 (pulse)
Speed/position switch control (absolute system)
• 0 to 359.99999 (degree)/0 to 359.99999 (degree)
0.01 to 6000000.00 (mm/min)/0.01 to 375000.00 (mm/min) *5
Speed
Command
0.001 to 600000.000 (inch/min)/0.001 to 37500.000 (inch/min)
0.001 to 600000.000 (degree/min)/0.001 to 37500.000 (degree/min)
1 to 1000000 (pulse/s)/1 to 62500 (pulse/s)
388
*1
*2
*3
*4
*5
*6
The circular interpolation function is not available when a stepping motor is used.
PC-9800 Series is a registered trademark of NEC
DOS/V is a registered trademark of IBM Japan, Ltd.
In the absolute method, the control unit of the speed/position switch control is "degree" only.
Indicates the setting range of "standard mode/stepping motor mode."
The automatic S-curve acceleration/deceleration is not available when a stepping motor is used.
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Positioning Module: AJ65BT-D75P2-S3
Module Features
Axis LED display
CC-Link status
LED display
These LEDs display power-supply status
and data-communication status.
LED name
PW
These LEDs display information indicating operation status according to the selected mode.
On: Normal operation
RUN
RS-422 connector
for peripherals
This connector is used for connection with
peripheral devices.
Item checked
On: When the power supply is turned on
17-segment LED display
L RUN
On: When the communication is normal
SD
Turns on during data
transmission
RD
Turns on during data reception
L ERR.
On: Communication data error
Transmission speed
setting switch
Terminal block
This is used for setting the data
communication speed.
Terminal for connecting to the master module
Setting
number
Transmission
speed
Drive module connectors (AX1 and AX2)
0
156 kbps
These connectors are used to connect to drive modules, mechanical system
inputs and manual pulse generators.
1
625 kbps
2
2.5 Mbps
LED display mode selector switch
3
5 Mbps
4
10 Mbps
The information displayed in the "[1] Axis LED display" and the "17-segment
LED display" is switched every time this switch is pressed.
Station number
setting switches
These switches are used for setting the
station number of D75P2.
Reset switch
Press this switch to initialize input signal, remote register, and calculation
processing.
External Dimensions
63.5
9.5
Unit: mm
Rated plate
80
Two ø4.5mm mounting holes
71
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
These LEDs indicate the axis to which the
information displayed if the "17-segment
LED display" applies.
161
170
Mitsubishi Electric Automation
|
Distributed I/O 389
n Allows full access to controller programs and memory via the CC-Link network via built-in RS-422 port.
n Perform program upload and download from across the network.
n Certification: UL • cUL • CE
Performance Specifications
Model Name
AJ65BT-G4-S3
D-sub 25 pin 1 channel
Intelligent device station
1 stations (32 points each for RX/RY, 4 words each for RWr/RWw)
Peripheral Device Connector
Station Type
Number of Occupied Stations
Allowable Momentary
1ms
Power Failure Period
RAV1.25 to 3.5, RAV2 to 3.5 (compliant to JIS C 2805)
M4 x 0.7 mm x 16 mm screws or larger
Possible to mount on a DIN rail
TH35-7.5Fe, TH35-7.5Al, TH35-15Fe (compliant to JIS C 2812)
0.19A
Applicable Solderless Terminal
Module Mounting Screws
Applicable DIN Rail
24 VDC Internal Current Consumption
External Power Supply
(For Driving the Module)
24 VDC (15.6 to 28.8 V)
Weight
External Dimensions
0.36kg
80(W) x 170(H) X 63.5(D) mm
Module Features
Transmission speed setting switch
Setting number
0
1
2
3
4
Other than 0 to 4
Transmission speed
156 kbps (factory setting)
625kbps
2.5Mbps
5Mbps
10Mbps
Not used
(If other than 0 to 4 is set, L ERR. LED turns on
and a communication error occurs.
MITSUBISHI
Station number setting switches
These switches are used for setting the station
number of G4-S3 in the range from 1 to 63 or 1 to 64.
B RATE
A J65BT-G4-S3
0 1
PW
RUN
L RUN
SD
RD
L ERR.
4
2
3
SW1 SW6 MODE
OFF OFF
A
ON OFF
QnA
OFF ON
Q
ON ON non-used
STATION NO.
X10
X1
0 1
9 0 1
2 8
2
3 7
3
6 5 4
6 5 4
SW
1 2 3 4 5 6 7 8
RESET
ON
Reset switch
Hardware reset
RS-422
Operation setting DIP switch
This is used for setting the operation specification of
G4-S3.
Switch
no.
1.6
Terminal block for power supply and data link
On: When the power supply is turned on
On: Normal operation
On: Normal communication
Turns on during data transmission
Turns on during data reception
Off: When the communication is normal
RS-422 interface
Interface for connecting peripheral devices
Peripheral
device
transmission
speed (bps)
4.5
7
8
Not used
Not used
Test mode
SW1 SW6
OFF OFF
ON OFF
OFF ON
ON ON
Operation mode
A mode
QnA mode
Q mode
Setting not allowed
SW2 SW3
OFF OFF
ON OFF
OFF ON
ON ON
Transmission speed
9600bps
19200bps
38400bps
Setting not allowed
Fixed at OFF
---Online mode
Test mode
External Dimensions
Two ø4.5mm mounting holes
9.5
4.5
Unit: mm
MITSUBISHI
B RATE
A J65BT-G4-S3
0 1
63.5
Rated plate
PW
RUN
L RUN
SD
RD
L ERR.
4
SW1 SW6 MODE
OFF OFF
A
ON OFF
QnA
OFF ON
Q
ON ON non-used
RS-422
4.5
161
170
390
2
3
STATION NO.
X10
X1
0 1
9 0 1
2 8
2
3 7
3
6 5 4
6 5 4
SW
1 2 3 4 5 6 7 8
RESET
ON
80
PW
RUN
L RUN
SD
RD
L ERR.
2.3
Status of setting switch
ON
OFF
71
LED display
Setting
item
Operation
mode
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Peripheral Device Connection Module • AJ65BT-G4-S3
CC-Link Repeater Module • AJ65SBT-RPT
Performance Specifications
Model Name
AJ65SBT-RPT
Maximum Number of Connected
Modules (Levels) Per Segment
10
Varies depending on the transmission speed.
Same as the normal CC-Link system (a system consisting of one segment)
Maximum Transmission Distance Of
Each Segment
Number of Occupied Stations
(Stations)
None
Station Numbers That Can Be Set
Power Supply Voltage
No station number
20.4 to 26.4 VDC
0.06 A (at TYP 24 VDC)
Current Consumption
External Dimensions
87.3(W) X 54(H) X 40(D) mm
0.2kg
Weight
Module Features
Operation LED display
The status of the module can be checked by the on/off status of the LED display.
LED
PW
At normal operation
At hardware test
On: The power supply is turned on.
Off: The power supply is turned off, or the reset switch is pressed.
TEST
Reset switch
Test switch
Pressing this switch resets the module's hardware.
(The factory setting is OFF.)
Switch status
Operation status
ON
Hardware test
OFF
Normal operation
This is used to set the operating condition of the
module. (The factory setting is OFF.)
Switch status
Operation status
ON
Hardware test
OFF
Normal operation
On: A hardware test is being performed.
Off: During communication operation
ERR.
On: Hardware error
The switch setting value is abnormal.
PW
On: Communication error
The switch setting value is
abnormal.
TEST
Flashing: The switch setting value
was changed during operation.
Off: Normal
Off: Communication is normal.
RD1
SD2
RD2
OUT
TEST
B RATE
4 2 1
ON
AJ65SBT-RPT
SD1
Flashing: The circuit is normal.
Flashing: Transmitting data to the IN side.
RD1
RD2
SD1
RESET
DA1
SD2
ERR.
IN
Flashing: The switch setting value was
changed during operation.
IN
Off: The circuit is abnormal.
Off: Not transmitting data to the IN side.
Flashing: The IN side circuit is normal.
Off: The IN side circuit is abnormal.
Flashing: Receiving data from the IN side.
Off: No reception data from the IN side.
Flashing: The circuit is normal.
Flashing: Transmitting data to the OUT side.
Off: The circuit is abnormal.
Off: No data is transmitted to the OUT side.
Flashing: The OUT side circuit is
normal.
Off: The OUT side circuit is
abnormal.
Flashing: Receiving data from the
OUT side.
Off: No reception data from the OUT
side.
DG1
DB1
+24V
24G
SLD
DA2
(FG)
DG2
DB2
OUT
NC
SLD
NC
(FG)
Transmission speed setting switch
This is used for setting the transmission speed of the
module. (The factory setting is 0.)
Make sure to set the transmission speed in the range
below. The "ERR." LED of the LED display turns on if
a setting other than the ones listed below is made.
IN side terminal block
This terminal block is used to connect the CC-Link dedicated cable on the side where the power supply and
master station exist.
OUT side terminal block
This terminal block is used to connect the CC-Link dedicated cable on the side where the master station does not exist.
Setting
value
DIN rail hook
Hook for mounting the module to the DIN rail
Press on the centerline of the DIN rail hook until it clicks in order to mount the module.
Point
The settings of the test switch and transmission speed setting switch are valid as made when the power supply to the module is turned off and back on again
or the reset switch is turned off.
The operations above should be performed again if the settings are changed while the power supply to the module is turned on.
System Configuration
0
1
2
3
4
Status of setting switch
4
2
1
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
Transmission
speed
156kbps
625kbps
2.5Mbps
5Mbps
10Mbps
External Connections
[Segment]
Master station
[Segment(first level)]
Remote
device station
Remote I/O station
Repeater
IN
Terminal resistor
(mandatory)
The following figure shows how to connect AJ65SBT-RPT to the CC-Link system with
cables.
Intelligent
device station
(AJ65SBT-RPT)
OUT
Terminal resistor
(mandatory)
Terminal resistor
(mandatory)
Terminal
resistor
Terminal resistor
(mandatory)
Repeater (J65SBT-RPT)
[1st level]
IN
OUT
Intelligent
device station
Remote I/O station
Remote
device station
IN
OUT
AJ65SBT-RPT
DA1
DB
DB1
DG
DG1
CC-Link dedicated
cable
FG
Terminal resistor
(mandatory)
[2nd level]
Master module
DA
SLD
Terminal resistor
(mandatory)
Terminal
resistor
Repeater(AJ65SBT-RPT)
Local station
Remote I/O station
SLD
FG
Remote I/O module
DA
Terminal
resistor
DB
DG
CC-Link dedicated
cable
SLD
FG
Local module
AJ65SBT-RPT
DA1
DA2
DA
DB1
DB2
DB
DG1
DG2
SLD CC-Link dedicated
FG cable
SLD
FG
Terminal
resistor
DG
CC-Link dedicated
cable
SLD
FG
Terminal resistor
(mandatory)
Terminal resistor
(mandatory)
Terminal
resistor
*1 The repeater is a module used to connect each segment and extend the CC-Link system.
*2 In a CC-Link system using repeaters, a block of devices connected by wiring from one
terminal resistor to another terminal resistor is referred to as a segment. (A conventional
CC-Link system can be said to be a single-segment configuration.)
*3 It is necessary to match the transmission speed of each segment to the transmission speed of the master
DA2
AJ65SBT-RPT
DA1
DA
DB2
DB1
DB
DG2
DG1
DG
SLD CC-Link dedicated
FG cable
SLD CC-Link dedicated
FG cable
SLD
Terminal
resistor
Important
It is possible to use CC-Link dedicated cables
of different specifications for each segment.
However, within each segment CC-Link dedicated cables with the same specifications
should be used. Normal data transmission cannot be guaranteed if multiple specifications are
used.
Point
* Make sure to connect a terminal resistor to the
modules at both ends of a segment. Terminal resistors should also be connected between DA and DB
(between DA1 and DB1 as well as DA2 and DB2 in
case of AJ56SBT-RPT).
* The terminal resistors used vary according to the
type of cable used. For more information, see the
user's manual for the master module to be used.
* The shielded wire of the CC-Link dedicated cable
should be connected to " SLD" of each module, and
both sides should be treated with Class D grounding
(Class 3 grounding) via "FG ." Note that SDL and FG
are connected within the module.
FG
External Dimensions
Terminal
resistor
78.3 +10 (mounting pitch)
Two 4.5mm x 5.1mm mounting holes
(for M4 mounting screws)
40
PW
TEST
ERR.
SD1
RD1
SD2
RD2
16.5
RESET
IN
OUT
TEST
B RATE
4 2 1
ON
AJ65SBT- RPT
50
DA1
IN
DB1
DG1
+24V
SLD
DA2
24G
(FG)
OUT
DG2
DB2
NC
SLD
DA2
DA
DB2
DB
DG2
DG
SLD CC-Link dedicated
FG cable
SLD
Terminal
resistor
FG
NC
(FG)
87.3
Unit: mm
4
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n Allows distance of a CC-Link network to be extended up to 13.2 km with regular BA1SJ61-S or BA1SJ61-P cable.
n Use a maximum of 10 repeaters per segment.
n Allows T-branch configurations.
n Certification: UL • cUL • CE
Mitsubishi Electric Automation
|
Distributed I/O 391
n Allows distance of a CC-Link network to be extended up to 7.8 km using optical fiber cable.
n Use in environments where noise is a problem.
n Use a maximum of 6 repeaters per segment.
n Allows T-branch configurations in regular copper network cable.
n Certification: UL • cUL • CE
Performance Specifications
Model Name
AJ65SBT-RPG
AJ65SBT-RPS
Voltage
Power
Supply
Common
Specification
20.4 to 26.4 VDC
0.06 A (at TYP 24 VDC)
Current
118(W) x 54(H) x 40(D)mm
0.2kg
External Dimensions
Weight
Terminal resistors (110 x 1, 130 x 1)
Supplied Parts
CC-Link
Communication
Specification
Optical
Communication
Specification
Maximum Number of
Connected Levels in a System
3 levels
2 levels
None
Number of Occupied Stations
Connection Cable
Applicable Connector
SI-200/220
QSI-185/230
GI-50/125
CA9103S
1000m
2000m
CA7003
Maximum Transmission
Distance of Optical Fiber
Cable Between Repeaters
500m
Module Features
Operation LED display
The status of the module can be checked by the on/off status of the LED display.
PW
LED name
At hardware test
TWI.SD
TEST
B RATE
4 2 1
DA
DB
On: Hardware error
The switch setting value is abnormal.
On: Communication error
The switch setting value is abnormal.
Flashing: The switch setting value was
changed during operation.
Flashing: The switch setting value
was changed during operation.
Off: Normal
Off: Communication is normal.
Flashing: The circuit is normal.
Flashing: Not transmitting data to the CCLink side.
DG
+24V
SLD
A J65SBT-RPS
24G
(FG)
Off: Not transmitting data to the
CC-Link side.
Flashing: Receiving data from the
CC-Link side.
Off: No reception data from the
CC-Link side.
Off: The circuit is abnormal.
Transmission speed setting switch
Flashing: The CC-Link side circuit is
normal.
Off: The optical communication side
circuit is abnormal.
OPT.SD
Flashing: The circuit is normal.
Flashing: Transmitting data to the
optical communication side.
DIN rail hook
Off: The circuit is abnormal.
Off: No data is transmitted to the
optical communication side.
Optical interface
Flashing: Receiving data from the
optical communication side.
Off: No reception data from the optical
communication side.
Flashing: The CC-Link side circuit is
normal.
Off: The optical communication side
circuit is abnormal.
IN
OUT
TWI.RD
OPT.RD
RD
OPT.
MITSUBISHI
Off: During communication operation
ERR.
SD
ON
TWI.
Off: The power supply is turned off.
On: A hardware test is being performed.
TEST
RD
TEST ERR. SD
At normal operation
On: The power supply is turned on.
PW
Terminal block
This terminal block is used for
connecting the power supply and
CC-Link dedicated cables.
Test switch
This is used to set the operating condition of the module. (The factory setting is OFF.)
Switch status
Operation status
ON
Hardware test
OFF
Normal operation
This is used for setting the transmission speed of the
module. (The factory setting is 0.)Make sure to set the
transmission speed in the range below. The "ERR."
LED of the LED display turns on if a setting other than
the ones listed below is made.
Status of setting switch
4
2
1
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
Setting
value
0
1
2
3
4
Transmission
speed
156kbps
625kbps
2.5Mbps
5Mbps
10Mbps
Point
The settings of the test switch and transmission speed setting switch are valid as made while the power supply to the
module is turned off and back on again.The operations above should be performed again if the settings are changed
while the power supply to the module is turned on.
System Configuration
[Segment *2 ]
Master station
*3
Repeater *1
(AJ65SBT-RPS/RPG)
Remote I/O
station
Repeater *1
(AJ65SBT-RPS/RPG)
Intelligent
device station
Combinations of optical repeater module and optical fiber cable
to be used
The optical repeater modules can be used in the following combinations with optical fiber cable.
Optical repeater module
[Segment (first level)]
*1
Remote I/O
station
Repeater
(AJ65SBT-RPS/RPG)
Intelligent
Remote
device station
device station
Remote
device station
[Segment (first level)]
Local station
Remote I/O station
AJ65SBT-RPS
AJ65SBT-RPG
Remote I/O station
Optical fiber cable
QSI-type optical fiber cable
(maximum extension distance of cable: 1000 m)
GI-type optical fiber cable
(maximum extension distance of cable: 2000 m)
*1 The repeater is a module used to connect each segment and extend the CC-Link system.
*2 In a CC-Link system using repeaters, a block of devices connected by wiring from one terminal resistor to another terminal resistor is referred to as a segment. (A conventional CC-Link system can be said
to be a single-segment configuration.)
*3 It is necessary to match the transmission speed of each segment to the transmission
speed of the master station.
*4 Up to 3 levels can be used in one segment (up to 2 levels when AJ65SBT-RPG modules are used).
Repeater *1
(AJ65SBT-RPS/RPG)
[Segment (second level)] *4
Remote I/O station
Optical fiber cable
SI-type optical fiber cable
(maximum extension distance of cable: 500 m)
Repeater *1
(AJ65SBT-RPS/RPG)
CC-Link dedicated cable
Terminal resistor (mandatory)
External Dimensions
External Connections
Unit: mm
AJ65SBT-RPS/RPG
Remote module
DA
DA
DA
DB
DB
DG
DG
SLD
FG
Optical
Interface
SLD
FG
Optical fiber cable
Optical
Interface
Terminal
resistor
DA
DA
DB
DB
DG
DG
SLD
392
Important
CC-Link dedicated cables with the same specifications
should be used within each segment. Normal data
transmission cannot be guaranteed if multiple
specifications are used.
CC-Link dedicated
cable
SLD
FG
FG
AJ65SBT-RPS/RPG
Local module
Terminal
resistor
Point
*Make sure to connect a terminal resistor to the
modules at both ends of a segment.
Terminal resistors should also be connected between DA and DB. (Terminal resistors are supplied
with the module.)
*The terminal resistors used vary according to the
type of cable used.For more information, see the
user's manual for the master module to be used.
*The shielded wire of the CC-Link dedicated cable
should be connected to " SLD" of each module,
and both sides should be treated with Class D
grounding (Class 3 grounding) via "F G." Note that
SDL and FG are connected within the module.
118
109 +10 (mounting pitch)
Two 4.5mm x 5.1mm (for M4 mounting screws)
16.5
CC-Link dedicated
cable
FG
Terminal
resistor
DG
PW TEST ERR. SD
RD
SD
RD
TEST
B RATE
4 2 1
ON
TWI.
OPT.
MITSUBISHI
DA
50
SLD
DB
CC-Link dedicated
cable
DB
DG
+24V
SLD
A J65SBT-RPS
24G
(FG)
OUT
4
Terminal
resistor
Master module
40
The following figure shows how to connect AJ65SBT-RPS/RPG to the CC-Link system with cables.
IN
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link Optical Repeater Modules: AJ65SBT-RPS • AJ65SBT-RPG
CC-Link Wireless Optical Repeater Module: AJ65B-RPI-10A • AJ65BT-RPI-10B
Performance Specifications
AJ65BT-RPI-10A • AJ65BT-RPI-10B
Model name
Power
Supply
Common
Specification
CC-Link
Communication
Specification
Voltage
Current
20.4 to 26.4 VDC
0.137A (at TYP. 24VDC)
External Dimensions
Weight
161(W) x 100(H) x 57.5(D) mm
Transmission Speed
2.5M/625k/156kbps
0.5kg
Maximum Number of Connected
Levels in a Segment
2 levels
Number of Occupied Stations
When the monitoring function is used: 1 (remote I/O station), when the monitoring function is not used: 0 (no station is occupied)
Optical Transmission Distance
0 to 100 m
When the optical transmission distance is 0 to 50 m: Total angle ±2
Angle of Beam Spread ( °)
Optical
Communication
Specification
When the optical transmission distance is 50 to 100 m: Total angle ±1
Modulation Frequency
Module A to module B: 36 ± 3 MHz
Module B to module A: 44 ±2.5MHz
Modulation Method
Specially Noted
General Specification
FSK
Ambient Illumination *
Must be 10000 lx or less (avoid direct sunlight)
*Reference values (based on JIS Z9110) of ambient illumination are shown below.
Illumination required for detailed visual work in a plant: 3000 to 1500 lx
Illumination required for work in an office: 2000 to 750 lx
Module Features
S1
S2
S3
RC
R1
R2
R3
SLD
DG
DB
LERR
ERR
DA
SD1
RD1
SD2
2
RD2
FG
+24V 24G
1
TERMINATER
OFF
ON
4 5 6
4 5 6
4 5 6
LRUN
3
Enlarged view
S
B RATE
7 8
C
PW
4 5 6
ST NO.X10
7 8
4 5 6
1
LRUN
2
LERR
ST NO.X1
7 8
Enlarged
view
3
ERR
R
C
9 0 1
SC
PW
1
2
3
4 5 6
RD2
C
R
C
ST NO.X1
7 8
9 0 1
RD1
S
B RATE
7 8
ST NO.X10
7 8
2 3
SD2
These are used for fixing the module to the
mounting metal fittings.
9 0 1
SD1
Module mounting screws
This is the lens surface
used for performing
optical communication.
9 0 1
ERR
Transmission speed
156kbps
625kbps
2.5Mbps
Setting not allowed
0
1
2
3 to 9
Lens surface
9 0 1
LERR
Setting value
2 3
LRUN
Description
On: The power supply is turned on.
Off: The power supply is turned off.
On: Normal communication while the monitoring function
is used
Off: When a communication error occurred while the
monitoring function is used, or
while the monitoring function is not used
On: When a communication error occurred while the
monitoring function is used, or
while the monitoring function is not used
Off: Normal communication while the monitoring function
is used
On: Communication error
Off: Normal
On: Sending data to the cable side
Off: Not sending data to the cable side
On: Sending data to the optical output side
Off: Not sending data to the optical output side
On: Receiving data from the connection cable side
Off: Not receiving data from the connection cable side
On: Receiving data from the optical input side
Off: Not receiving data from the optical input side
RY (n+1) 0 is turned on.
Off: RY (n+1) 0 is turned off.
On: RY (n+1) 1 is turned on.
Turns on only
Off: RY (n+1) 1 is turned off.
when the
On: RY (n+1) 2 is turned on.
monitoring
Off: RY (n+1) 2 is turned off.
function is used.
On: RY (n+1) 3 is turned on.
Off: RY (n+1) 3 is turned off.
On: Optical reception is enabled for the self-station.
Off: Optical reception is disabled for the self-station.
On: The margin in light reception of the self-station is 1.5
times or more.
Off: The margin in light reception of the self-station is less
than 1.5 times.
(Using RC as the standard.)
On: The margin in light reception of the self-station is 2.0
times or more.
Off: The margin in light reception of the self-station is less
than 2.0 times.
(Using RC as the standard.)
On: The margin in light reception of the self-station is 2.5
times or more.
Off: The margin in light reception of the self-station is less
than 2.5 times.
(Using RC as the standard.)
2 3
PW
This is used for setting the transmission
speed of the module.
(The factory setting is 0.)
2 3
LED name
Transmission speed
setting switch
2 3
The status of the module can be checked by the on/off
status of the LED display.
2 3
Operation LED display
9 0 1
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n Wireless optical link is ideal for rotating machinery, to replace festoon cabling, etc.
n Use “A” and “B” modules as a pair.
n Certification: CE
1
FG
TERMINATER
OFF
ON
DA
SD1
DB
DG
SLD
RD1
SD2
2
+24V 24G
RD2
3
Station number setting switch (ten digits)
Terminal block
Station number setting switch (unit digits)
This terminal block is used for connecting the power supply
and CC-Link dedicated cable.
This is used for setting the station number of the module,
and to set whether or not to use the monitoring
function. (The factory setting is OFF.)
Terminal resistor switch
00
01 to 64
65 to 99
When the monitoring function
should not be used
Station number when the
monitoring function is used
Setting not allowed
Display window mounting screw
This screw is used for fixing the display window to the module.
Remove the display window when performing the switch setting.
This is used for setting whether or not to use the module's
built-in terminal resistor (110 ). (The factory setting is 0.)
Mounting metal fittings
Metal fittings for mounting the module
Point
The settings of the transmission speed setting switch and station number
setting switches are valid as made while the power supply to the module
is turned off and back on again.
The operations above should be performed again if the settings are
changed while the power supply to the module is turned on.
Mitsubishi Electric Automation
|
Distributed I/O 393
Here it is explained how to connect the AJ65BT-RPI10A/10B to the CC-Link system with the CC-Link dedicated
cables. Remove the terminal block protection cover of the
modules beforeperforming the wiring work.
Terminal
resistor
Master module
AJ65BT-RPI-10A/10B
Remote module
DA
DA
DA
DB
DB
DB
DG
SLD
FG
DG
DG
CC-Link dedicated
cable
Important
CC-Link dedicated cables with the same specifications should
be used within each segment. Normal data transmission
cannot be guaranteed if multiple specifications are used.
SLD
FG
Lens
surface
CC-Link dedicated
cable
SLD
FG
Wireless transmission
Terminal
resistor
Lens
surface
DA
DA
DB
DB
DG
DG
Point
SLD
CC-Link dedicated
• Make sure to connect a terminal resistor to the modules
cable
FG
at both ends of a segment. Terminal resistors should also be connected
between DA and DB. (Terminal resistors are supplied with the module.)
AJ65BT-RPI-10A/10B
• The terminal resistors used vary according to the type of cable used.
For more information, see the user's manual for the master module to be used.
• The shielded wire of the CC-Link dedicated cable should be connected to "SLD" of each module, and
both sides should be treated with Class D grounding (Class 3 grounding) via "FG." Note that SDL and
FG areconnected within the module.
SLD
FG
Local module
Module Dimensions
Ø mounting hole (for M6 mounting screw)
Three Ø 7mm x 16mm mounting holes (for M6 mounting screws)
B RATE
S
C
7 8
5
0
2 3
100.0
84.0
40.0
ST NO.X10
7 8
0
5
LRUN
2
LERR
3
2 3
ST NO.X1
7 8
ERR
R
C
1
SD1
RD1
SD2
0
5
PW
1
45.0
44.0
2
RD2
2 3
3
35.5
57.5
8.0
130.0
145.0
161.0
128.0
Ø 42
12.0
2.0
35.5
Optical axis adjustment angle
±4° for both left/right and up/down
394
Terminal
resistor
Unit: mm
Terminal
resistor
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Module Connection
CC-Link RS-232 Interface Module: AJ65BT-R2
n Provides a single RS-232 port directly on the CC-Link network.
n Allows general purpose RS-232 devices to be located remotely (Printer, barcode, reader, etc.)
n Certification: UL • cUL • CE
Model Name
RS-232
Specification
External Connections
AJ65BT-R2
Conforms to single-channel RS-232 A
Interface Specification
The following shows how to connect the pins of the RS-232
interfaces of the AJ65BT-R2 module and the external device.
Full duplex communication method
Transmission Method
Synchronization Method
Asynchronous method
Transmission Speed
300, 600, 1200, 2400, 4800, 9600, 19200 bps
Example of connection where DC code control and
DTR/DSR signal control are possible
AJ65BT-R2 side (DTE)
Signal code
Pin no.
SD
3
RD
2
RS
7
CS
8
DR
6
SG
5
CD
1
ER
4
(Selected by the RC-232 transmission specification setting switch)
Data
Format
Start Bit
1
Data Bit
7/8
Parity Bit
1 (yes) / 0 (no)
1/2
Stop Bit
Error Detection
Odd/even parity check/no parity check
DTR/DSR (ER/DR) control
Communication Control
(Flow Control)
DC1/DC3 control
15m
Transmission Distance
General-Purpose
I/O Specification
Input side: 24 VDC (sink/source common type) 2 points
Output side: Transistor output (sink type) 12/24 VDC 2-point terminal block B
Example of connection where only DC code control is possible
C
AJ65BT-R2 side (DTE)
Signal code
Pin no .
Intelligent device station
CC-Link Station Type
Number of Occupied
Signal code
SD
RD
RS
CS
DR
SG
CD
ER
5120 bytes
OS Reception Area
Data Link
Specification
External device (DTE)
Cable connection and
signal method
1 station (32 points each for RX/RY, 4 words each for RWr/RWw)
SD
RD
RS
CS
DR
SG
CD
ER
Stations
Power Supply Voltage
24 VDC
Current Consumption
Typically 110 mA (24 VDC), 180 mA (16.8 V) maximum
EEPROM Writing Life
100,000 times
External Dimensions
170(W) x 80(H) x 63.5(D) mm
Weight
395g
ExtExternal
er nal dedevice
vice (DTE) (DTE)
Cable connection and
signal method
Signal code
SD
RD
RS
CS
DR
SG
CD
ER
3
2
7
8
6
5
1
4
Transmission speed setting switch
Transmission speed
156kbps
625kbps
2.5Mbps
5Mbps
10Mbps
Setting error
Setting value
0
1
2
3
4
5to9
Module Features
Station number setting switches
These switches are used for setting the station
number of the module.
Reset switch
Pressing this switch causes the module to return to
the status when the power supply is turned on.
RS-232 transmission specification setting switch
This is used for setting the RS-232 transmission specification.
Number
Setting item
SW1to 8
Transmission
speed
SW4
SW5
SW6
SW7
SW8
Not used
Number of data bits
Parity bit enable/d
isable
SW
Status of setting switch
ON
OFF
1
2
3
300bps
0
0
0
600bps
1
0
0
1200bps
0
1
0
2400bps
1
1
0
4800bps
0
0
1
9600bps
1
0
1
19200bps
0
1
1
0:OFF 1:ON
Terminal block for
general-purpose input/output
This is used for connecting I/O wires.
RS-232 interface
External Dimensions
Mode setting switch
This is for setting the operating condition of the module.
Number
0
1
D
Name
Setting
Online mode
(The automatic buffer memory
update function is not active.)
Online mode
(The automatic buffer memory
update function is active.)
Online communication mode.
The automatic buffer memory update
function is not active.
Online communication mode.
The automatic buffer memory update
function is active.
Mode to confir
m that the module itself
oper ates proper
ly .
Hardw
are test mode
Terminal block for data link
A twisted pair cable is connected for the power supply
and data link (two-piece terminal)
Two ø4.5mm mounting holes
Unit: mm
4.5
LED name
PW
RUN
Setting item
7
Disable
Odd
1
71
80
Description
Turns on when the power is normally supplied.
Turns on when the module is normal, and turns off at a
WDT error.
L RUN Turns on when the network communication is normal.
Status
L ERR. Turns on when the network communication is
abnormal (e.g., CRC error).
Other
SD
Flashes when sending data link data.
RD
Flashes when receiving data link data.
XC,XD
Status of general-purpose inputs.
YC,YD
Status of general-purpose outputs.
RS-232 SD
Turns on when sending RS-232 data.
RS-232 RD
Turns on when receiving RS-232 data.
RS-232 ERR
Turns on at an RS-232 transmission error, etc.
Initial
status
This is used for an RS-232 cable
connected to an external device.
9.5
Operation LED display
8
Enable
Even
2
63.5
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Performance Specifications
4.5
161
170
Mitsubishi Electric Automation
|
Distributed I/O 395
n The AJ65SBT-CLB provides a way to link a CC-Link / LT network to a CC-Link network.
n Certification: UL • cUL • CE
Performance Specifications
Model
AJ65SBT-CLB
CC-Link
Station Type
Remote device station
Selected between 2, 4 and 8 stations*
When 2 stations are selected: 64 points for each of RX/RY
(16 points used by the system), 8 words for each of RWr/RWw
When 4 stations are selected: 128 points for each of RX/RY
(16 points used by the system), 16 words for each of RWr/RWw
When 8 stations are selected: 256 points for each of RX/RY
When 8 stations are selected: 256 points for each of RX/RY
Number of Occupied Stations
CC-Link/LT
Number of CC-Link Occupied Stations
Maximum Number
of CC-Link/LT
Connected Stations
2 stations occupied
4 stations occupied
8 stations occupied
4-Points Mode
12 stations
28 stations
56 stations
8-Points Mode
6 stations
14 stations
28 stations
16-Points Mode
3 stations
7 stations
14 stations
Remote Station Numbers
Bridge Station Connection Position
1 to 56
Connected at the end of the trunk line
*When 8 stations are occupied, make parameter setting so that two 4-station occupying modules are consecutively connected.
396
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
CC-Link — CC-Link / LT Bridge Module
Module Features
LED Display
Operation setting switch
PW
Lit during correct operation of module.
Lit: During correct operation of module
Unlit: Clock stop or no power supply
L RUN
State of data link
Lit:
Data link e
xec resution in prog
UnData
lit: link eror (time-out)
Common
L ERR.
L RUN
auData
lt station
link f detection
Lit:
CC-Link side s
CRC
ault inf reciv
BlinkCC-Link
:
side s
ation
oper
UnNo
lit: f
ault
Description of LED
Station number
setting switch
STATION NO.
Use STATION NO. "10," "20" and "40" to set the tens digit of the station number.
Use STATION NO. "1," "2," "4" and "8" to set the units digit of
the station number.
Station
No.
1
2
3
4
..
10
11
..
63
witchaultsetting f
ed data
witch ingchanged dur
<Du
ingr r
egular oper
ation>
Lit:
Data link e
xec resution in prog
UnData
lit: link stopped
<Self lok teopst -mobade>c
Lit:
Self loop-bac
kmatestl nor
UnSelit:lf loop-bac
auk telts f
Red
<Du
ingr r
egular oper
ation>
Lit:
Data link f
ault station detection.
Some stations are out of control r
BlinkData
:
link f
ault at all stations
UnNo
lit: f
ault
<Ink testself lom opde>-bac
Lit:
Self loop-bac
auk telts f
UnSelit:lf loop-bac
kmatestl nor
L ERR.
2.
CC-Link/LT
part
ERR.
CC-Link
1.
CC-Link part
Name
Description of LED
Color
.ange
Seautting
lt detectfion
Lit:
L T side s
witchaultsetting f
BlinkL: T side s
witch ingchang
oper ed dur
UnNo
lit: f
ault
Tens digit
20
OFF
OFF
OFF
OFF
40
OFF
OFF
OFF
OFF
10
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
OFF
4
OFF
OFF
OFF
ON
Units digit
2
OFF
ON
ON
OFF
1
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
ON
ON
All switches are OFF in the factory shipment state. When two stations
are occupied, the setting range is from "1" to "63." When four stations
are occupied, the setting range is from "1" to "61." When eight stations
are occupied, the setting range is from "1" to "57." Settings out of the
permissible range cause a setting error. Transmission speed
setting switch
Transmission speed
setting switch
B RATE
4
Setting switch
2
1
Transmission
speed
0(Factory
shipment setting)
OFF
OFF
OFF
156 kbps
1
2
3
4
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
OFF
625 kbps
2.5 Mbps
5.0 Mbps
1 0Mbps
Setting
ation
Settings other than above cause a setting error.
Number of occupied
stations setting switch
NOS: Numbers of
Occupied Stations
PW
CC-Link
L RUN L RUN
CC-Link/LT
L RUN L ERR
CC-LINK
ERR
CC-LINK/LT
A J65SBT-CLB
2
1
0(Factory
shipment setting)
OFF
OFF
2 stations
1
2
OFF
ON
ON
OFF
4 stations
8 stations
Settings other than above cause a setting error.
Self loop-back test
setting switch
CC-Link / LT
OFF: Regular operation mode (Factory shipment setting)
ON: Self loop-back test mode
Number of points mode
setting switch
MODE
Setting switch
2
1
Setting
0 (Factory
shipment state)
1
2
Number of
points
OFF
OFF
8 points
OFF
ON
ON
OFF
4 points
16 points
Settings other than above cause a setting error.
Number of points mode
setting switch
B RATE
CC-Link/LT
interface connector
Setting switch
2
1
Setting
Transmission
speed
0 (Factory
shipment state)
OFF
OFF
156kbps
1
2
OFF
ON
ON
OFF
625kbps
2.5Mbps
Settings other than above cause a setting error.
External Dimensions
87
78 ±0.4
40
10
(4)
(4.5)
CC-LINK/LT
L RUN L ERR ERR
CC-LINK
STATION NO
B RATE
CC-LINK/LT
NOS TST MODE B RATE INC
22
CC-LINK
L RUN L ERR
ON
(FG)
CC-LINK
Two 4.5mm x 5.1mm
(for M4 mounting screws)
41 ±0.2
49
PW
Center of DIN rail
(4)
4.5
CC-Link
interface connector
Number of
Occupied Stations
Setting switch
Setting
STATION NO
B RATE NOS TST MODE B RATE INC
40 20 10 8 4 2 1 4 2 1 2 1
2 1 2 1
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8
CC-Link/LT
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Name of
LED
Mitsubishi Electric Automation
|
Distributed I/O 397
Specifications
AJ95FPBA4-16DE
Certification
Number of Input Points
Isolation Method
Rated Input Voltage
Rated Input Current
Operating Voltage Range
Max. Simultaneous ON Input Points
ON Voltage /ON Current
OFF Voltage /OFF Current
Input Resistance
OFFàON
Response Time
ONàOFF
Common Wiring Method
Input Method
Number of Stations Occupied
Voltage
I/O Module
Power Supply
Current
Noise Durability
Dielectric Withstand Voltage
Insulation Resistance
Weight kg (lbs)
Level of Protection
Required Manual
Dimensions (W x H x D) mm (in)
Appearance
UL • cUL • CE
16
Photocoupler
24 VDC
Approx. 7 mA
20.4 to 26.4 VDC (ripple ratio within 5%)
100%
14V or higher / 3.5 mA or higher
6V or lower / 1.7 mA or lower
Approx 3.3 kΩ
1.5 ms or lower (when 24 VDC)
1.5 ms or lower (when 24 VDC)
16 points / 1 common
(waterproof connector 2 to 4 wire type)
Source type
1 station
20.4 to 26.4 VDC (ripple rate: with 5%)
65 mA or lower (when 24 VDC and all points are ON)
DC type noise voltage 500Vp-p, noise width 1 µs, noise
carrier frequency 25 to 60Hz (noise simulator condition)
500 VAC for 1 minute between all DC external
terminals and ground
10 MΩ or higher, measured with a 500 VDC insulation
resistance tester
0.40 (0.88)
IP67
AJ95FPBA4-16DE User's ManuaI • IB(NA)0800220 (Included)
60 (2.56) x 192 (7.76) x 48 (1.89)
External Connection
Communication Connector
Pin. Number
LINK IN
LINK OUT
1
Vacant
Vacant
2
RxD/TxD(N)
RxD/TxD(N)
3
DGND
DGND
4
RxD/TxD(P)
RxD/TxD(P)
5
Shield
Shield
Power Supply Connector
Pin. Number
Unit Power
1
+24V
2
Vacant
3
24G
4
Vacant
5
FG
I/O Connector
Signal
Signal
Pin No.
Pin No.
Name
Name
X0/X1
X2/X3
X4/X5
X6/X7
398
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
+24V
X1
24G
X8/X9
X0
Vacant
+24V
X3
24G XA/XB
X2
Vacant
+24V
X5
24G XC/XD
X4
Vacant
+24V
X7
24G
XE/XF
X6
Vacant
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
+24V
X9
24G
X8
Vacant
+24V
XB
24G
XA
Vacant
+24V
XD
24XG
XC
Vacant
+24V
XF
24G
XE
Vacant
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Profibus-DP Node Style Waterproof DC Source Input Module, 4 Wire, M12 Connector
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Profibus-DP Waterproof Source Transistor Output Module, 2 Wire, M12 Connector
Specifications
Certification
Number of Output Points
Isolation Method
Rated Load Voltage
Operating Load Voltage Range
Max. Load Current
Max. Load Inrush Current
Leakage Current at OFF
Max. Voltage Drop at ON
Output Method
OFFàON
Response Time
ONàOFF
Voltage
External Power
Supply for Output
Current
Common Wiring Method
Surge Supressor
Number of Stations Occupied
Voltage
I/O Module
Power Supply
Current
Noise Durability
Dielectric Withstand Voltage
Insulation Resistance
Weight kg (lbs)
Required Manual
Dimensions (W x H x D) mm (in)
External
Connection
AJ95FPBA2-16TE
UL • cUL • CE
16 points
Photocoupler
12 / 24 VDC
10.2 to 26.4 VDC (ripple ratio within 5%)
0.1A / point; 4.0 A/1 common
2.0A 10ms or lower
0.3 mA or lower
0.15 VDC or lower (TYP) 1.0A; 0.2 VDC or lower (MAX) 0.1A
Source type with protection (thermal, short circuit)
0.5 ms or lower
1.5 ms or lower (resistive load)
10.2 to 28.8 VDC (ripple ratio: within 5%)
Appearance
25 mA or lower (24 VDC/all pts. ON) Not including external load current
16 points / 1 common (waterproof connector 2 wire type)
Zener diode
1 station
20.4 to 26.4 VDC (ripple ratio: within 5%)
75mA or lower (when 24 VDC and all points are ON)
DC type noise voltage 500Vp-p, noise width 1 µs, noise
carrier frequency 25 to 60Hz (noise simulator condition)
500 VAC for 1 minute between all DC external
terminals and ground
10 MΩ or higher, measured with a 500 VDC insulation
resistance tester
0.40 (0.88)
AJ95FPBA2-16TE User’s Manual • IB(NA)0800221 (Included)
60 (2.56) x 192 (7.76) x 48 (1.89)
Communication Connector
Pin. Number
LINK IN
LINK OUT
1
Vacant
Vacant
2
RxD/TxD(N)
RxD/TxD(N)
3
DGND
DGND
4
RxD/TxD(P)
RxD/TxD(P)
5
Shield
Shield
Power Supply Connector
Pin. Number
Unit Power
AUX
1
+24V
+24V
2
Vacant
Vacant
3
24G
24G
4
Vacant
Vacant
5
FG
FG
I/O Connector
Signal
Signal
Pin No.
Pin No.
Name
Name
Y0/Y1
Y2/Y3
X4/X5
Y6/Y7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Mitsubishi Electric Automation
Vacant
Y1
24G
Y8/Y9
Y0
Vacant
Vacant
Y3
24G
YA/YB
Y2
Vacant
Vacant
Y5
24G YC/YD
Y4
Vacant
Vacant
Y7
24G
YE/YF
Y6
Vacant
|
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Vacant
Y9
24G
Y8
Vacant
Vacant
YB
24G
YA
Vacant
Vacant
YD
24G
YC
Vacant
Vacant
YF
24G
YE
Vacant
Distributed I/O 399
Specifications
Certification
INPUT SPECIFICATION
Number of Input Points
Isolation Method
Rated Input Voltage
Rated Input Current
8 points
Photocoupler
24 VDC
Approx. 7mA
Operating Voltage Range
20.4 to 26.4 VDC (ripple ratio: within ±5%)
Max. Simultaneous on Input Points
ON Voltage /ON Current
OFF Voltage /OFF Current
Input Resistance
Response
Time
OFFàON
ONàOFF
AJ95FPBA42-16DTE
UL • cUL • CE
OUTPUT SPECIFICATION
Number of Output Points
Isolation Method
Rated Load Voltage
Operating Load Volt. Range
Max Load Current
100%
14 V or higher / 35 mA or higher
Max Inrush Current
Leakage Current at OFF
6 V or lower / 1.7 mA or lower
Max. Voltage Drop at ON
Approx. 3.3Ω
1.5 ms or lower (when 24 VDC)
1.5 ms or lower (when 24 VDC)
Output Form
Response Time
External Power
Supply / Output
Input Form
Common Wiring Method
No. of Stations Occupied
Voltage
I/O Module
Power Supply
Current
Noise Durability
Dielectric Withstand Voltage
Insulation Resistance
Weight kg (lbs)
Required Manual
Dimensions (W x H x D) mm (in)
Source type
8 points / 1 common
(waterproof connector 2 to 4 wire type)
OFFàON
ONàOFF
Voltage
Current
Surge Suppression
Common Wiring Method
8 points
Photocoupler
12/24 VDC
10.2 to 28.8 VDC (ripple range ± 5%)
1.0 A / point,:
4.0A/1 common
2.0A 10 msec or lower
0.3 mA or lower
0.15 VDC or lower (TYP) 1.0A
0.2 VDC or lower (MAX) 1.0A
Source type with protection (thermal, short circuit)
0.5 msec or lower
1.5 msec or lower (resistive load)
10.2 to 28.8 VDC (ripple rate within 5%)
15mA or lower (24 VDC all pts. ON.)
Not including external load current
Zener diode
8 points / 1 common
(waterproof connector 2 wire type)
1 station
20.4 to 26.4 VDC (ripple rate within 5%)
70 mA or lower (at 24 VDC app pts. ON)
DC type noise voltage 500V p-p
According to the noise simulator of noise frequency 25 to 60Hz, noise width 1 µs
500 VAC for 1 minute between all DC external terminals and ground
10 MΩ or higher, measured with 500 VDC insulation resistance tester
0.40
AJ95FPBA42-16DTE User’s Manual • IB(NA)0800222 (Included)
60 (2.56) x 192 (7.76) x 48 (1.89)
Communication Connector
Pin. Number
LINK IN
LINK OUT
1
Vacant
Vacant
2
RxD/TxD(N)
RxD/TxD(N)
3
DGND
DGND
4
RxD/TxD(P)
RxD/TxD(P)
5
Shield
Shield
Power Supply Connector
Pin. Number
Unit Power
AUX.
1
+24V
+24V
2
Vacant
Vacant
3
24G
24G
4
Vacant
Vacant
5
FG
FG
I/O Connector
Signal
Signal
Pin No.
Pin No.
Name
Name
X0/X1
X2/X3
X4/X5
X6/X7
400
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
+24V
X1
24G
X0
Vacant
+24V
X3
24G
X2
Vacant
+24V
X5
24G
X4
Vacant
+24V
X7
24G
X6
Vacant
Y0/Y1
Y2/Y3
Y4/Y5
Y6/Y7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
Vacant
Y1
24G
Y0
Vacant
Vacant
Y3
24G
Y2
Vacant
Vacant
Y5
24XG
Y4
Vacant
Vacant
Y7
24G
Y6
Vacant
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Profibus-DP Waterproof Source Transistor Input/Source Transistor Output Module,
4 Wire Input, 2 Wire Output, M12 Connector
Profibus Bus I/O:
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Profibus-DP Bus Node Module
The modular format of the MT Profibus I/O modules allows greater flexibility
in tailoring a mixture of I/O types to your application.
n
Special Features:
n The bus module connects all I/O modules to the network.
n 0.5 transistor output modules.
n
n
n
2A relay output.
Isolation between the I/O and network.
Screw terminal or spring clamp type terminals.
Two selectable types of connecting terminals: screw type and
cache clamp terminals.
Specifications
MT-DP12
Certification
Module Type
Communications
Protocol
Medium
Interface
Operation Modes
Communications Rate
Max. Total Distance (m)
No. of Connectable I/O Modules
Addressable Digital I/Os
I/O Points
Applicable Wire Size (mm 2)
Power Supply (VDC)
Internal Current Consumption (24 VDC)
Weight (kg)
Dimensions (W x H x D) mm
Optional Accessories
Required Manual
CE
MT I/O bus module, Profibus-DP slave
DIN 19245-T3
Shielded twisted-pair 24AWG (0.22 mm 2), impedance: 100 – 130 Ω; Shielded twisted-pair (22AWG =0.34 mm 2), impedance: 135 – 165 Ω
RS-485
Sync mode and freeze mode are supported
9.6; 19.2; 93.75; 187.5; 500 kbit/s, 1.5; 3; 6; 12 Mbit/s
4800 (3 repeaters)
16, including up to 4 analog I/O modules
192
—
0.75 – 2.5
24
500 mA (max.)
0.28 (0.62)
96 (3.78)x 114 (4.49) x 60 (2.36)
Local system adapter MT-LE with extension cable MT-LE-CBL50 (length 0.5 m) = MT-LE-SET
Screw type terminal block MT-DP12-TBS; Cache clamp terminal block MT-DP12-TBC,
PROFIBUS 9-pin D-SUB plug connector for up to 12 Mbaud: ProfiCon.
IB(NA)6610 Not included (purchase separately) Profibus MT Series Manual. Covers all MT type bus style Profibus I/O
Note: Many of these manuals are available by free download from our website, www.meau.com
Profibus-DP Bus I/O
Choose from 4, 8 or 16 point I/O modules to accurately tailor the
I/O system to your application.
Specifications
Certification
Inputs
Outputs
Output Type
Common Terminal Arrangement
Isolation
Input Voltage (Sensor Supply)
Output Voltage Range
Max. Switching Voltage
Rated Input Current (A)
Max. Current
24 VDC (±25%)
—
—
0.7
24 VDC (±25%)
—
—
0.7
—
Per Group (A)
—
—
≤1
≤1
Electronic
—
LED
OFFàON (ms)
ONàOFF (ms)
Shortcut Protection
Status Display for Outputs
Error Indicator
Connection Terminal
Applicable Wire Size (mm 2)
External Sensor Supply
Internal Power Consumption (8 VDC) mA
Weight kg (lb)
Dimensions (W x H x D) mm (in)
Accessories*
MT-X16
CE
16, source
—
—
—
Per Output (A)
Leakage Current at OFF
Response Time
MT-X8
CE
8, source
—
—
—
Terminal Blocks
(Order separately)
0.75 – 2.5
—
25
0.16 (0.35)
MT-Y8T
MT-Y16T
CE
CE
—
—
8
16
Source Transistor
Source Transistor
8
8
By optocoupler
—
—
24 VDC (-1%)
24 VDC (-1%)
30 VDC
30 VDC
—
—
MT-Y8T2
CE
—
8
Source Transistor
4
MT-Y4R
CE
—
4
Relays
1
—
24 VDC (-0.5%)
30 VDC
—
—
24/110/220 VAC/DC
220 VAC
—
2A (24/110/220 VAC)
—
0.5
0.5
2
0.25A (110 VDC)
0.1A (220 VDC)
—
2.5
2.5
10
—
—
<50 µA
<50 µA
6 µA
—
≤1
≤0.14
≤0.14
0.3
10 ms
≤1
≤0.05
≤0.05
≤0.08
5 ms
Electronic
Electronic
Electronic
Electronic
—
—
All modules have one or two status LEDs per output
LED
LED
LED
—
—
All modules can be fitted with screw type or cache clamp terminal blocks (see accessories)
0.75 – 2.5
0.75 – 2.5
0.75 – 2.5
0.75 – 2.5
0.75 – 2.5
24 VDC (≤20 mA)
24 VDC (≤20 mA)
24 VDC (≤20 mA)
24 VDC (≤20 mA)
24 VDC (≤30 mA)
30
35
60
35
45
0.17 (0.37)
0.16 (0.35)
0.16 (0.35)
0.18 (0.40)
0.175 (0.39)
56(2.20) x 114 (4.49) x 60 (2.36)
MT-X8-TBS
MT-X16-TBS
MT-Y8T-TBS
MT-Y16T-TBS
MT-Y8T2-TBS
MT-Y4R-TBS
MT-X8-TBC
MT-X16-TBC
MT-Y8T-TBC
MT-Y16T-TBC
MT-Y8T2-TBC
MT-Y4R-TBC
MT-X16-PTBS
MT-Y16T-PTBS
MT-X16-PTBC
MT-Y16T-PTBS
* Guide to terminal block types: TBS = I/O screw terminals, TBC = I/O spring clamp terminals, PTBS = I/O screw type terminals with additional terminals for supplying power to I/O devices,
PTBC = I/O spring clamps with additional terminals for supplying power to I/O devices.
Mitsubishi Electric Automation
|
Distributed I/O 401
The MT modular system also allows you to flexibly incorporate analog as
well as digital I/O into your Profibus system.
Special Features:
n 4 separately parameterizable channels per module.
n Voltage, current, and temperature input can be set via parameter.
Specifications
Certification
Module Type
Number of Channels
Analog Input
Digital Output
Digital Input
Analog Output
Input
Resistance
Max. Output Load
n
n
n
With the analog input module, current, voltage, and PT100 inputs can be
operated in parallel.
Two selectable types of connecting terminals: screw type and spring
clamp terminals.
Standard potential isolation between network and I/O.
MT-4AD-N
CE
Analog input module
4
-10 V – +10 V, -20 mA – +20 mA, 4 – 20 mA, -180 – +600 °C (PT100)
Voltage (kΩ)
Current (Ω)
I/O Characteristics
Max. Resolution
Max. Conversion Time
Isolation
Connection Terminal
Applicable Wire Size mm 2
Internal Power Consumption (8 VDC) mA
Weight kg (lb)
Dimensions (W x H x D) mm (in)
Accessories (Order Separately)
MT-4DAV
CE
Analog output module
4
—
—
16 bits binary (incl. sign)
0 – 10 VDC
—
—
≥750Ω
Digital Input
Analog Output
16 bits binary (incl. sign)
—
—
176
approx. 50
—
Analog Input
Digital Output
-10 to +10 V
-4000 to +4000
-20 to+20mA
-4000 to +4000
0 –4000
0 –10V
4 to 20mA
0 to +4000
-180 to +600°C
-1800 to +6000
-10 to +10 V
approx. 2.5mV
-20 to +20mA
approx. 5µA
—
2.5mV
4 to 20mA
approx. 4 µA
-180 to +600 °C
approx. 0.125 °C
50 ms/channel
1 ms/channel
Optocoupler isolation
Optocoupler isolation
Both modules can be fitted with screw type or spring clamp terminal blocks (see accessories).
0.75 – 2.5
0.75 – 2.5
80
60
0.225 (0.50)
0.22 (0.50)
76 x 114 x 60
Screw type terminal block MT-4AD-TBS-S1
Screw type terminal block MT-4DAV-TBS
Spring clamp terminal block MT-4AD-TBC-S1
Spring clamp terminal block MT-4DAV-TBC
CC-Link/ LT
CC-Link/LT offers a cost effective way to network small groups of digital I/O for applications such as in-panel wiring and similar uses.
Key features:
n
n
n
n
n
402
Attach wiring to I/O blocks with no cutting or stripping of cable: devices simply clip on to the cable, leading to significant labor
and material cost savings.
Fast communication speed.
Up to 1024 I/O per segment.
Fine granularity of I/O allows placement of small quantities of I/O where required.
Can be connected to an existing CC-Link network via the AJ65SBT-CLB bridge module.
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Profibus-DP Analog I/O Modules
Required Manuals
Manual Part Number
IB(NA)0800232
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
SH(NA)080351
IB(NA)0800240E
SH(NA)080362E
Description
QJ61CL12
AJ65SBT-CLB
Included?
User’s Manual (Hardware)
Yes
User’s Manual
No
User’s Manual (Hardware)
Yes
User’s Manual
No
JY997D04101
CL1X4-D1B2
User’s Manual
Yes
JY997D04201
CL1Y4-T1B2
User’s Manual
Yes
JY997D04301
CL1Y4-R1B2
User’s Manual
Yes
JY997D05501
CL1Y4-R1B1
User’s Manual
Yes
JY997D05601
CL1XY4-DT1B2
User’s Manual
Yes
JY997D05701
CL1XY4-DR1B2
User’s Manual
Yes
IB(NA)0800233E
CL2X8-D1B2
User’s Manual (Hardware)
Yes
IB(NA)0800234E
CL2Y8-TP1B2
User’s Manual (Hardware)
Yes
JY997D04401
CL1XY8-DT1B2
User’s Manual
Yes
JY997D04501
CL1XY8-DR1B2
User’s Manual
Yes
IB(NA)0800256E
CL2X8-D1S2
User’s Manual (Hardware)
Yes
IB(NA)0800257E
CL2Y8-TP1S2
User’s Manual (Hardware)
Yes
JY997D10801
CL1X4-D1S2
User’s Manual
Yes
JY997D10901
CL1Y4-T1S2
User’s Manual
Yes
IB(NA)0800235E
CL2X8-D1C3V
User’s Manual (Hardware)
Yes
IB(NA)0800236E
CL2Y8-TP1C2V
User’s Manual (Hardware)
Yes
IB(NA)0800258E
CL2X16-D1C3V
User’s Manual (Hardware)
Yes
IB(NA)0800259E
CL2Y16-TP1C2V
User’s Manual (Hardware)
Yes
IB(NA)0800260E
CL2XY16-DTP1C5V
User’s Manual (Hardware)
Yes
JY997D10601
CL1X4-D1C3
User’s Manual
Yes
JY997D10701
CL1Y4-T1C2
User’s Manual
Yes
IB(NA)0800264E
CL2TE-5
User’s Manual (Hardware)
Yes
IB(NA)0800265E
CL2TE-10S
User’s Manual (Hardware)
Yes
IB(NA)0800237E
CL2X16-D1M1V
User’s Manual (Hardware)
Yes
IB(NA)0800238E
CL2Y16-TP1M1V
User’s Manual (Hardware)
Yes
JY997D03901
CL1X2-D1D3S
User’s Manual
Yes
JY997D04001
CL1Y2-T1D2S
User’s Manual
Yes
JY997D03801
CL1XY2-DT1D5S
User’s Manual
Yes
JY997D09901
CL1-HLD
User’s Manual (Hardware)
Yes
User’s Manual
Yes
JY997D04601
JY997D06601
CL1PAD1
User’s Manual (Detailed)
No
JY997D09801
CL1PSU-2A
User’s Manual
Yes
JY997D05901
CL1XY8-DTE1B2
User’s Manual
Yes
JY997D06301
CL1XY2-DTE1D5S
User’s Manual
Yes
JY997D06501
CL1Y2-TE1D2S
User’s Manual
Yes
JY997D05801
CL1Y4-TE1B2
User’s Manual
Yes
User’s Manual (Hardware)
Yes
User’s Manual
No
User’s Manual (Hardware)
Yes
User’s Manual
No
IB(NA)0800289E
SH(NA)080417E
IB(NA)0800290E
SH(NA)080418E
CL2AD4-B
CL2DA2-B
Mitsubishi Electric Automation
|
Distributed I/O 403
This section presents the current line-up of CC-Link/LT I/O blocks. For the network master modules, please refer to the appropriate controller section. Before using this guide, please read the following guide to nomenclature:
CL
1
3
2
4
1 Unit for CC-Link/LT
:1 or 2
2 Unit type
X: Input
Y: Output
XY: I/O hybrid
5
7
6
3 Total number of I/O points
2:
4:
8:
16:
5 Connection form
2 points
4 points
8 points
16 points
B:
C:
M:
D:
4 I/O specifications
Terminal block
Sensor connector
MIL connector
Cable type
7 Shape
S:Ultracompact
V: Vertical type
None: Normal type
(horizontal type)
6 Wire type
D1: 24VDC input
R1: Relay output 2A
T1: Transistor output 0.1A
TP1: Transistor output 0.1A
(with output protection)
DT1: 24VDC input/
transistor output 0.1A
DR1: 24VDC input/
relay output 2A
1:
2:
3:
5:
1-wire type
2-wire type
2- or 3-wire type
Input 2 or 3-wire type, output 2-wire type
Note on "1-wire", "2-wire" & "3-wire" terminology
Throughout the CC-Link/LT blocks, we reference these terms. These are concise definitions for the following ways to connect I/O devices:
• 1 wire: One side of the load is connected to the I/O module terminal block. The other side is connected to a common terminal shared by all devices.
• 2 wire: One side of the load is connected to the I/O module terminal block. The other side is connected to a dedicated common terminal for that load on
the terminal block. Note that in some cases, the common terminals may be connected internally.
• 3 wire: The I/O block is configured to accept loads with three connections (such as various types of sensor, etc)
CC-Link/LT Accessories
The following connectors and cable for CC-Link/LT are available:
NOTE: ALL CONNECTORS AND ACCESSORIES ARE SOLD SEPARATELY. PLEASE INSURE YOU HAVE ALL NECESSARY
CONNECTORS BEFORE BEGINNING AN INSTALLATION.
Product
Model Number
Description
Quantity Per Box
AWG
Dedicated Flat Cable
CL9-FL4-18-* *
Where * * = length
(sold by the meter)
10 m
N/A
Connector
Terminating Resistor
CL9-CNF-18
CL9-RYVK
ECN-A014R
ECN-A004Y
ECN-A024BL
ECN-A104
ECN-A154
ECN-M014R
ECN-M024Y
ECN-M034OR
ECN-M044GN
ECN-M054BL
ECN-M064GY
ECN-M114R
ECN-M124Y
ECN-M134OR
ECN-M144GN
ECN-M154BL
ECN-M164GY
—
10
2
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
—
N/A
N/A
28 - 24
24 - 22
22 - 20
N/A
N/A
26 - 24
26 - 24
26 - 24
22 - 20
22 - 20
22 - 20
26 - 24
26 - 24
26 - 24
22 - 20
22 - 20
22 - 20
—
A Type Plug (*1)
A Type
Receptacle (*1)
M Type Plug (*1)
Open Sensor Connector
M Type
Receptacle (*1)
MIL Type (*2)
Notes:
1. Use with CLXXX-XXCXXX type blocks
2. Use with CLXXX-XXXMXXX type blocks
404
Red
Yellow
Blue
Panel / Wall mounting type
Relay connection type
Red
Yellow
Orange
Green
Blue
Gray
Red
Yellow
Orange
Green
Blue
Gray
Available from 3rd parties
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Guide to CC-Link/LT I/O
CC-Link/LT Power Supply Adapter
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CC-Link/LT requires 24VDC power to be supplied to the network. The two options for
doing this are the CL1PAD1 and the CL1PSU-2A. CL1PAD1 allows network power to
be derived from a 24VDC supply, whereas the CL1PSU-2A allows a 120VAC supply
to be used.
CL1PAD1
UL • cUL
28.8VDC
Maximum Input Current
Insulation Resistance
5.0A
10MΩ across input-FG by 500VDC insulation resistance tester
LINK
1
2
3
4
LINK/POWER
CL1PAD1
Internal
circuit
CC-Link/LT
interface connector
+24V
DA
DB
24G
-DA
DB
--
LINK
1
2
3
4
LINK/POWER
CL1PAD1
Internal
circuit
Stabilized power supply
24VDC
1 +24V
+
2 24G
3
CL1PAD1 to external PSU: screw terminals
CL1PAD1 to CC-Link/LT network: CL9-CNF-18 connectors
to network cable.
External Connection System
Dimensions (W x H x D) mm (in)
66 x 85 x 90 (2.5 x 3.3 x 3.5)
Specifications
CL1PSU-2A
Rated Voltage
100, 120, 200, 230, and 240V AC
Voltage Allowable Range
85 to 264V AC
Rated Current
1.2A / 100V AC 0.7A / 200V AC
Rated Frequency
50 or 60Hz
Power Fuse
3.15A
Inrush Current
Output
1
2
3
4
+24V
DA
DB
24G
-DA
DB
--
Stabilized power supply
24VDC
1 +24V
+
2 24G
3
CC-Link/LT
interface connector
Specifications
Certification
Maximum Input Voltage
Input
CC-Link/LT
interface connector
CC-Link/LT
interface connector
1
2
3
4
Max. 50A / 100V AC Max. 60A / 200
Output Voltage
24V DC +10 %/-5 %
Output Current
0.01A to 2A Derating occurs according to the ambient
temperature and power voltage. [Use the module in a proper
range so that the total current consumption of each module
does not exceed 2A (except the period immediately after the
power is turned on).]
Ripple Noise
500mVp-p or below
By noise simulator of 1000Vp-p in noise voltage,1 s in
noise width, and 25 to 60Hz in frequency
Noise Resistance
CC-Link/LT to CC-Link Bridge Module
The AJ65SBT-CLB allows a CC-Link/LT network segment to be connected to a CC-Link
network. The module uses the A6CON-L5P & A6CON-LJ5P network connectors.
Model
AJ65SBT-CLB
CC-Link
Station Type
Remote device station
Selected between 2, 4 and 8 stations
*When 2 stations are selected: 64 points for each of RX/RY
(16 points used by the system), 8 words for each of RWr/RWw
When 4 stations are selected: 128 points for each of RX/RY
(16 points used by the system), 16 words for each of RWr/RWw
Number Of Occupied Stations
When 4 stations are selected: 128 points for each of RX/RY
(16 points used by the system), 16 words for each of RWr/RWw
When 8 stations are selected: 256 points for each of RX/RY
(32 points used by the system), 32 words for each of RWr/RWw
CC-Link/LT
Number Of CC-Link Occupied Stations
Maximum Number of
CC-Link/LT
Connected Stations
2 stations occupied
4 stations occupied
8 stations occupied
4-Points Mode
12 stations
28 stations
56 stations
8-Points Mode
6 stations
14 stations
28 stations
16-Points Mode
3 stations
7 stations
14 stations
Remote Station Numbers
Bridge Station Connection Position
1 to 56
Connected at the end of the trunk line
Note: When 8 stations are occupied make parameter setting so that two 4-station occupying modules are consecutively connected.
Mitsubishi Electric Automation
|
Distributed I/O 405
n DISTRIBUTED I/O
Input Module
Model Name
Input Type
Number
Of Input
Points
Isolation
Method
Rated Input
Voltage
OFF-ON
ON-OFF
External
Connection
Wire Type
Common
Connection
Internal Current Consumption
On Voltage Off Voltage
Operating Voltage
CL1X4-D1B2
DC
+COM/-COM
4
Photocoupler
24VDC
19VDC min 11VDC max
0.5ms/1.5ms max
0.5ms/1.5ms max
Two wire
4 points/common
40mA
CL2X8-D1B2
DC
+COM/-COM
8
Photocoupler
24VDC
19VDC min 11VDC max
0.5ms/1.5ms max
0.5ms/1.5ms max
Two wire
8 points/common
40mA
Rated Load
Voltage
Maximum Load Current
Output Response Time
Output Module
Model Name
Output Type
Sink
Number
of Output
Points
Isolation
Method
1 Point
1 Common
OFF-ON
ON-OFF
Leakage
Current
Surge
Suppression
External Connection Wire
Type
Common Connection
Internal Current
Consumption
CL1Y4-T1B2
Transistor
4
Photocoupler
12/24VDC
0.1A
0.4A
1.0ms
1.0ms
0.1mA
Zener diode
Two wire
4 points/common
60mA
CL1Y4-R1B2
Relay
4
Mechanical
250VAC/30VDC
2A
4A
10ms
10ms
N/A
N/A
Two wire
4 points/common
65mA
CL1Y4-R1B1
Relay
4
Mechanical
250VAC/30VDC
2A
2A
10ms
10ms
N/A
N/A
One wire
1 point/common
65mA
CL2Y8-TP1B2
Transistor
8
Photocoupler
12/24VDC
0.1A
0.8A
0.5ms
0.5ms
0.1mA
Zener diode
Two wire
8 points/common
40mA
Combined I/O
Module Model
Name
Sink
I/O Type
Number
of I/O
Points
Isolation
Method
Input/Load
Voltage
Input
Response
Time
Maximum Output Load
Current
1 Point
Input Operating Voltage
1 Common On Voltage
Output Response Time
Off Voltage
OFF-ON
ON-OFF
Connection
Surge
Internal
Wire Type
Leakage
Common
Suppres- on Input/
Current
Current
Connection
Output
sion
Consumption
Sides
CL1XY4-DT1B2
DC input/
transistor
output
+COM/
-COM/sink
2/2
Photocoupler/
photocoupler
24VDC/
24VDC &
12VDC
1.5ms
0.1A
0.2A
19VDC min
11VDC max
1.0ms
1.0ms
0.1mA
Zener
diode
Two wire/
two wire
2 points/
common/
2 points/
common
55mA
CL1XY4-DR1B2
DC input/
relay
output
+COM/
-COM
2/2
Photocoupler/
mechanical
24VDC/
250VAC &
30VDC
1.5ms
2A
4A
19VDC min
11VDC max
10ms
10ms
N/A
N/A
Two wire/
two wire
2 points/
common/
2 points/
common
60mA
CL1XY8-DT1B2
DC input/
transistor
output
+COM/
-COM/sink
4/4
Photocoupler/
photocoupler
24VDC/
24VDC &
12VDC
1.5ms
0.1A
0.4A
19VDC min
11VDC max
1.0ms
1.0ms
0.1mA
Zener
diode
Two wire/
two wire
4 points/
common/
4 points/
common
65mA
CL1XY8-DR1B2
DC input/
relay output
4/4
Photocoupler/
mechanical
24VDC/
250VAC &
30VDC
1.5ms
2A
4A
19VDC min
11VDC max
10ms
10ms
N/A
N/A
Two wire/
two wire
4 points/
common /
4 points/
common
70mA
Guide to Module Features
406
Input Response Time
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Performance Specifications: Screw Terminal Modules
External Dimensions
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CL1X4-D1B2
CL1Y4-T1B2
CL2X8-D1B2
CL2Y8-TP1B2
CL1Y4-R1B2 • CL1Y4-R1B1
CL1XY4-DT1B2 • CL1XY4-DR1B2
CL1XY8-DT1B2 • CL1XY8-DR1B2
External Connections
Mitsubishi Electric Automation
|
Distributed I/O 407
Input Module
Model Name
Input Type
CL1X4-D1S2
DC
+COM/-COM
CL2X8-D1S2
DC
+COM/-COM
Output Module
Model Name
Output Type
Number Of
Input
Points
Isolation
Method
Rated Input
Voltage
4
Photocoupler
8
Photocoupler
Operating Voltage
On Voltage
Off Voltage
24VDC
19VDC min
11VDC max
24VDC
19VDC min
11VDC max
Number of
Output
Points
Isolation
Method
Rated Load
Voltage
Maximum Load Current
Input Response Time
OFF-ON
0.5ms/
1.5ms max
0.5ms/
1.5ms max
External Connection
Wire Type
Common Connection
Internal Current Consumption
0.5ms/1.5ms max
Two wire
4 points/common
40mA
0.5ms/1.5ms max
Two wire
8 points/common
40mA
ON-OFF
Leakage Current
Surge
Suppression
External
Connection
Wire Type
Output Response Time
1 Point
1 Common
OFF-ON
ON-OFF
Common
Connection
Internal Current
Consumption
CL1Y4-T1S2
Transistor
Sink
4
Photocoupler
12/24VDC
0.1A
0.4A
1.0ms
1.0ms
0.1mA
Zener diode
Two wire
4 points/common
60mA
CL2Y8-TP1S2
Transistor
Sink
8
Photocoupler
12/24VDC
0.1A
0.8A
0.5ms
0.5ms
0.1mA
Zener diode
Two wire
8 points/common
40mA
Guide to Module Features
External Dimensions
CL1X4-D1S2 • CL1Y4-T1S2
CL2X8-D1S2 • CL2Y8-TP1S2
External Connections
408
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Performance Specifications: Spring Clamp Modules
Performance Specifications: e-CON (Sensor Connector Modules)
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Input Module
Model Name
Input Type
Number Of
Input Points
Isolation Method
Rated Input Voltage
Operating Voltage
On Voltage Off Voltage
Input Response Time
OFF-ON
External Connection Wire Type
Common Connection
Internal Current
Consumption
ON-OFF
CL1X4-D1C3
DC
+COM
4
Photocoupler
24VDC
19VDC min 11VDC max 0.5ms/1.5ms max
0.5ms/1.5ms max
Two wire/three wire
4 points/common
35mA
CL2X8-D1C3V
DC
+COM
8
Photocoupler
24VDC
19VDC min 11VDC max 0.5ms/1.5ms max
0.5ms/1.5ms max
Two wire/three wire
8 points/common
40mA
CL2X16-D1C3V
DC
+COM
16
Photocoupler
24VDC
19VDC min 11VDC max 0.5ms/1.5ms max
0.5ms/1.5ms max
Two wire/three wire
16 points/common
45mA
Leakage Current
Surge Suppression
External Connection Wire Type
Common Connection
Internal Current
Consumption
Output Module
Model Name
Output Type
Number
Of Output
Points
Isolation
Method
Rated Load Maximum Load Current Output Response Time
Voltage
1 Point 1 Common OFF-ON
ON-OFF
CL1Y4-T1C2
Transistor
Sink
4
Photocoupler
24VDC
0.1A
0.4A
1.0ms
1.0ms
0.1mA
Zener diode
Two wire
4 points/common
60mA
CL2Y8-TP1C2V
Transistor
Sink
8
Photocoupler
24VDC
0.1A
0.8A
0.5ms
0.5ms
0.1mA
Zener diode
Two wire
8 points/common
45mA
CL2Y16-TP1C2V
Transistor
Sink
16
Photocoupler
24VDC
0.1A
1.6A
0.5ms
0.5ms
0.1mA
Zener diode
Two wire
16 points/common
55mA
Number Of
I/O Points
Isolation
Method
Input/Load
Voltage
Input
Response
Time
Combined I/O
Module Model
Name
CL2XY16DTP1C5V
I/O Type
DC input/
transistor
output
+COM/sink
8/8
Photocoupler/
photocoupler
24VDC/
24VDC
0.5ms/
1.5ms
Maximum Output
Load Current
1 Point
0.1A
Input Operating Voltage
1 Common On Voltage
0.8A
19VDC min
Output Response Time
Off Voltage
OFF-ON
ON-OFF
11VDC max
0.5ms
0.5ms
Leakage
Current
Surge
Suppression
0.1mA
Zener
diode
Connection
Internal
Wire Type on Common
Current
Input/Output Connection
Consumption
Sides
Two wire or
three wire/
two wire
8 points/
common/
8 points/
common
50mA
Guide to Module Features
External Dimensions
CL1X4-D1C3 • CL1Y4-T1C2
CL2X16-D1C3V • CL2Y16-TP1C2V
CL2XY16-DTP1C5V
CL2X8-D1C3V
Mitsubishi Electric Automation
|
Distributed I/O 409
n DISTRIBUTED I/O
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
410
External Connections
Performance Specifications: MIL Connector Modules
Input Module
Model Name
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
CL2X16-D1M1V
Output Module
Model Name
CL2Y16-TP1M1V
Input Type
DC
+COM
Output Type
Transistor
Sink
Number of
input
points
Isolation
Method
Rated Input
Voltage
16
Photocoupler
24VDC
Number of
Output
Points
Isolation
Method
Rated Load
Voltage
16
Photocoupler
12/24VDC
Operating Voltage
On Voltage
Off Voltage
19VDC min
11VDC max
Internal Current Consumption
ON-OFF
External
Connection Wire
Type
Common Connection
OFF-ON
0.5ms
1.5ms
Two wire
16 points/common
45mA
Input Response Time
Maximum Load Current
Output Response Time
1 Point
1 Common
OFF-ON
ON-OFF
0.1A
1.6A
1.0ms
1.0ms
Leakage Current
Surge
Suppression
External
Connection
Wire Type
0.1mA
Zener diode
One wire
Common
Connection
Internal Current
Consumption
16 points/
common
50mA
Guide to Module Features
External Dimensions
External Connections
Mitsubishi Electric Automation
|
Distributed I/O 411
Input Module
Model Name
CL1X2-D1D3S
Output Module
Model Name
CL1Y2-T1D2S
Combined I/O
Module Model
Name
CL1XY2DT1D5S
Input Type
DC
+COM
Output Type
Transistor
Sink
I/O Type
DC input/
transistor
+COM/sink
Number
of Input
Points
Isolation Method
Rated Input Voltage
2
Photocoupler
24VDC
Isolation
Method
2
Photocoupler
24VDC
0.1A
Number
of I/O
Points
Isolation
Method
Input/Load
Voltage
Input
Response
Time
1 Point
N/A
0.1A
Rated Load
Voltage
Photocoupler 24VDC/24VD
/photocoupler
C
Guide to Module Features
1 Point
Input Response Time
OFF-ON
ON-OFF
19VDC min 11VDC max 0.5ms/1.5ms max 0.5ms/1.5ms max
Maximum Load
Current
Number
of Output
Points
1/1
Operating Voltage
On Voltage Off Voltage
Output Response Time
1 Common
OFF-ON
ON-OFF
0.2A
1.0ms
1.0ms
Maximum Output
Load Current
0.1A
19VDC min
Common Connection
Internal Current Consumption
Three wire
2 points/common
40mA
Leakage Current
Surge
Suppression
External Connection Wire
Type
Common Connection
Internal Current Consumption
0.1mA
Zener diode
Two wire
Input Operating Voltage
1 Common On Voltage
External Connection Wire
Type
Output Response Time
Off Voltage
OFF-ON
ON-OFF
11VDC max
1.0ms
1.0ms
2 points/common
Leakage
Current
0.1mA
Surge Connection Wire
Suppres- Type on Input/
sion
Output Sides
Zener
diode
Three wire/
two wire
External Dimensions
CL1X2-D1D3S • CL1Y2-T1D2S
CL1XY2-DT1D5S
External Connections
CL1X2-D1D3S
412
40mA
Common
Connection
Internal
Current
Consumption
1 point/common/
1 point/common
40mA
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Performance Specifications: Cable Type Modules
Performance Specifications: CL2AD4-B Analog-Digital Converter Module
Model
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Analog
Input
CL2AD4-B
Voltage
-10 to 10VDC (input resistance 1MΩ)
Current
0 to 20mADC (input resistance 250Ω)
Digital Output
15-bit signed binary (-4096 to 4095)
Analog Input
Range
I/O Characteristics, Maximum
Resolution, Accuracy (Accuracy
Relative To Maximum Value Of
Digital Output Value)
Voltage
Current
Conversion Speed
-10 to 10V
0 to 10V
0 to 5V
1 to 5V
0 to 20mA
4 to 20mA
Accuracy
Digital Output
Ambient Temp. Ambient Temp. Temperature Max. Resolution
Value
25 ± 5°C (*1)
0 to 55°C
Coefficient (*3)
-4000 to 4000
2.5mV
0 to 4000
± 0.2%
(±8 digit) (*2)
±4%
±80ppm / °C
(±8 digit) (*2) (±0.0080% /°C)
0 to 4000
1.25mV
1.0mV
5µA
4µA
200µs / 4 channel (*4)
Absolute Maximum Output
Voltage: ±15V, current: ±30mA
Analog Output
4 channels / 1 module
CC-Link/LT Station Type
Remote device station
Number Of Occupied Stations
16 point mode with four occupied stations (*5)
Specific Isolated Area
Isolation System
Dielectric Withstand
Insulation Resistance
Voltage
Between communication system terminals and all analog input terminals
Isolation
Between power supply system terminals and all analog input terminals
Photocoupler isolated
Transformer isolated
1 min. duration of
500VAC
500VDC
10MΩ or more
Non-isolated
—
—
Between communication system terminals and power supply system terminals
Across channels
Connected Terminal Block
Applicable Wire Size
Applicable Crimping Terminal
Installing The Module
Supported DIN Rail
Module
Power
Supply (*6)
Voltage
Direct-coupled, 14-point terminal block (M3 screw)
0.3 to 1.25mm2
RAV1.25-3 (conforming to JIS C2805), V1.25-3 (manufactured by JST Mfg. CO., Ltd.), 1.25-3, TG1.25-3 (manufactured by NICHIFU CO., Ltd.)
DIN rail attachment, screw mounting: No restrictions to the mounting orientation with M4 x 0.7mm x 16mm and over.
TH35-7.5Fe, TH35-7.5AI (conforming to JIS-C2812)
24 VDC (20.4VDC to 28.8 VDC, ripple ratio: within 5%)
Current Consumption
0.070A
Start Up Current
0.570A
Protection Degree
IP2X
Weight (kg)
0.15
Notes:
1. Standard accuracy
2. Digital indicates the digital output value
3. Accuracy for each 1°C temperature change
4. The conversion speed of the first order lag filter channel is 400µs when a first order lag filter is used.
5. The number of I/O occupied points (occupied station count) differs depending on the final channel permitted for conversion.
6. A dedicated power supply/supply adaptor is used to supply power.
External Dimensions
Mitsubishi Electric Automation
|
Distributed I/O 413
Model
CL2DA2-B
Digital
Input
Voltage
Current
15-bit signed binary (-4096 to 4095)
15-bit signed binary (-96 to 4095)
Analog
Output
Voltage
-10 to 10VDC (external load resistance: 1kΩ to 1MΩ)
Current
0 to 20mADC (external load resistance: 0 to 600Ω)
Analog Output
Range
I/O Characteristics, Maximum
Resolution, Accuracy (Accuracy
Relative To Maximum Value Of
Digital Output Value)
Voltage
Current
Conversion Speed
-10 to 10V
0 to 10V
0 to 5V
1 to 5V
0 to 20mA
4 to 20mA
Accuracy
Ambient Temp. Ambient Temp. Temperature Max. Resolution
25 ±5°C (*1)
0 to 55°C
Coefficient (*2)
-4000 to 4000
±0.2%
±0.4%
2.5mV
(±20mV)
(±40mV)
±80ppm
/°C
0 to 4000
1.25mV
±0.2%
±0.4%
(±10mV)
(±20mV)
1.0mV
(±0.0080% /°C)
5µA
±0.2%
±0.2%
0 to 4000
(±80µA)
(±40µA)
4µA
Digital
Input Value
200µs / 2 channel
Output Short-Circuit Protection
Provided
Absolute Maximum Output
Voltage: ±12V, current: +21mA
Analog Output Points
2 channels / 1 module
CC-Link/LT Station Type
Remote device station
Number Of Occupied Stations
16 point mode with two occupied stations (*3)
Specific Isolated Area
Isolation System
Dielectric Withstand
Insulation Resistance
Voltage
Between communication system terminals and all analog input terminals
Isolation
Between power supply system terminals and all analog input terminals
Photocoupler isolated
Transformer isolated
1 min. duration of
500VAC
500VDC
10MΩ or more
Non-isolated
—
—
Between communication system terminals and power supply system terminals
Across channels
Connected Terminal Block
Applicable Wire Size
Applicable Crimping Terminal
Installing The Module
Supported DIN Rail
Module
Power
Supply (*4)
Voltage
Direct-coupled, 14-point terminal block (M3 screw)
0.3 to 1.25mm2
RAV1.25-3 (conforming to JIS C2805), V1.25-3 (manufactured by JST Mfg. CO., Ltd.), 1.25-3, TG1.25-3 (manufactured by NICHIFU CO., Ltd.)
DIN rail attachment, screw mounting: No restrictions to the mounting orientation with M4 x 0.7mm x 16mm and over.
TH35-7.5Fe, TH35-7.5AI (conforming to JIS-C2812)
24 VDC (20.4VDC to 28.8 VDC, ripple ratio: within 5%)
Current Consumption
0.170A
Start Up Current
0.470A
Protection Degree
IP2X
Weight (kg)
0.15
Notes:
1. Standard accuracy
2. Accuracy for each 1°C temperature change
3. The number of I/O occupied points (occupied station count) differs depending on the final channel permitted for conversion.
4. A dedicated power supply/supply adaptor is used to supply power.
External Dimensions
414
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Performance Specifications: CL2DA2-B Digital-Analog Converter Module
CC-Link/LT Accessories
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Common Terminal Blocks CL2TE and CL2TE-10S
Use these terminal blocks to increase the number of common terminals on a CC-Link/LT I/O block in order
to increase wiring convenience.
Cable Type I/O Module Holder CL1-HLD
Use this holder to increase the convenience of mounting the cable type I/O modules. Can be bolted down
or DIN rail mounted.
Mitsubishi Electric Automation
|
Distributed I/O 415
n DISTRIBUTED I/O
MELSEC I/O Link
Advantages (Bus Topology)
Bus topology of MELSEC-I/O LINK gives an advantage of high
reliability. Shutdown of one remote I/O module doesn’t affect
communications of the others.
MELSEC I/O Link Module Input Specifications
Model Name
AJ55TB3-4D
AJ55TB3-8D
AJ55TB3-16D
AJ55TB32-4DT
AJ55TB32-8DT
AJ55TB32-16DT
AJ55TB32-4DR
AJ55TB32-8DR
AJ55TB32-16DR
Type
DC input
Sink/Source
DC input
Sink
DC input
Sink/Source
No. of
Points
4
8
16
2
4
8
2
4
8
Rated
Rated
Voltage Current
24VDC
7mA
Operation Voltage (V)
ON
OFF
14
6
Response Time (ms)
ON
OFF
10
10
Connection
Type
Points Per
Common
No. of
Stations
Terminal block
4
8
16
2
4
8
2
4
8
1
2
4
1
1
2
1
1
2
MELSEC I/O Link Module Output Specifications
Model Name
AJ55TB2-4T
AJ55TB2-8T
AJ55TB2-16T
AJ55TB2-4R
AJ55TB2-8R
AJ55TB2-16R
AJ55TB32-4DT
AJ55TB32-8DT
AJ55TB32-16DT
AJ55TB32-4DR
AJ55TB32-8DR
AJ55TB32-16DR
Type
Transistor
Sink
Relay
Transistor
Sink
Relay
No. of
Points
4
8
16
4
8
16
2
4
8
2
4
8
Rated
Voltage
Rated
Current
12/24 VDC
0.5A/pt, 2A/com
0.5A/pt, 4A/com
0.5A/pt, 8A/com
2
2
24 VDC
240 VAC
2A/pt, 8A/com
10
12
12/24 VDC
24 VDC
240 VAC
Response Time (ms)
ON
OFF
0.5A/pt, 1A/com
0.5A/pt, 2A/com
0.5A/pt, 4A/com
2A/pt, 4A/com
2A/pt, 8A/com
2
2
10
12
Connection
Type
Points Per
Common
Terminal
block
4
8
16
4
8
16
2
4
8
2
4
8
Notes:
1. AJ55TB32-modules are input and output combination modules.
2. AJ55TB32-occupies only one station number for 4 point inputs and 4 point outputs.
3. See page 418 for dimensional information.
Required Manuals
Model Number
Description
Contents
IB(NA)66574
MELSEC I/O Link Remote I/O System Master Module type
AJ51T64/A1SJ51T64
Covers all AJ55TBxx-xxx I/O blocks
Note: Many of these manuals are available by free download from our website, www.meau.com
416
Surge
Absorber
Zener
diode
None
Zener
diode
None
No. of
Stations
1
2
4
1
2
4
1
1
2
1
1
2
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
I/O points on the remote I/O modules are kept small so that just the
necessary number of I/O signals are distributed to locations where
control devices are located. In addition, no terminal resistance
requirement and the T shape branch feature gives maximum flexibility
of configuration and layout.
PROFIBUS-DP and I/O Link I/O Module Dimensions
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
Profibus-DP AJ95 I/O Modules
Profibus-DP MT Modules
Digital I/O and MT-4DA Modules
MT-DP12 Bus Interface
Profibus-DP MT Modules
Analog I/O Modules
MT-LE Module
Mitsubishi Electric Automation
|
Distributed I/O 417
Profibus
AJ95FPBA2-16TE
Sold by AA Electric 1-800-237-8274 Lakeland, FL • Lawrenceville, GA • Greensboro, NC • East Rutherford, NJ www.A-Aelectric.com
n DISTRIBUTED I/O
Profibus
AJ95FPBA4-16DE
Profibus
AJ95FPBA42-16DTE
n I/O Link Modules
Model
AJ55TB-4
AJ55TB-8
AJ55TB-16
418
X (m)
82
114
177
X (in)
3.23
4.49
6.97