Transcript
www.ronda-startech.com 21 60 30 Cal. 5040.B 45 20 15 10 30 9 10 1 8 7 2 3 6 5 4 Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW) Accuracy: +20 / -10 seconds per month English User’s Manual In case your watch needs to be repaired or to raise claims under a guarantee, please contact the point of sales Description of the display and control buttons Minute counter Push-button A Control buttons 45 20 � � 60 30 Display elements Chronograph: Basic function (Start / Stop / Reset) 21 Example: � Start: Press push-button A. 15 10 30 9 10 1 Date Second hand 6 21 Push button A 60 30 Minute hand 45 20 15 button A once more and read the three chronograph hands: 4min/38sec / 7⁄ 10 sec 4 5 second counter Crown 10 Hour hand 1⁄ 10 � Stop: to stop the timing, press push- 2 3 8 7 � Zero positioning: 30 21 9 10 1 8 7 Centre stop-second 2 3 6 5 Press push-button B. (The three chronograph hands will be reset to their zero positions). Push button B 4 60 30 45 Minute counter 20 15 10 30 9 10 1 1⁄ 10 2 3 8 7 second counter 6 (houer counter after 30 minutes) � 4 5 Push-button B Push-button A Minute counter 60 30 45 20 Chronograph: Accumulated timing � � � � 21 15 10 2 3 8 7 6 5 4 = 28 min 10 sec second counter � � 60 30 45 20 Chronograph: Intermediate or interval timing Push-button A 21 � Stop: (e.g. 15 min 5 sec following �) � Restart: (timing is resumed) �* Stop: (e.g. 13 min 5 sec following �) 30 9 10 1 1⁄ 10 Minute counter Example: � Start: (start timing) Example: � Start: (start timing) � Display interval: e.g. 10 minutes 10 seconds (timing continues in the background) *� Making up the measured time: (the 3 chronograph hands are quickly advanced to the ongoing measured time). � Stop: (Final time is displayed) � Reset: The 3 chronograph hands are returned to their zero position 15 10 30 9 10 1 8 7 � � 2 3 6 1⁄ 10 4 5 second counter Push-button B (The accumulated measured time is shown) � Reset: 21 45 45 Please note: * Following �, the accumulation of the timing can be continued by pressing pushbutton A (Restart / Stop, Restart / Stop, …) 30 9 10 1 2 3 6 5 � 4 Push-button B 21 � 45 15 10 30 9 10 1 2 3 8 7 6 1⁄ 10 I 5 II III 2 3 8 7 6 Push-button B Adjusting the next hand B B A Adjusting the 1⁄ 10 second counter hand (position 6h) Single step 1 x short A Continuous long A � 60 45 15 30 9 10 1 III 2 3 Adjusting the next hand B B 10 5 Adjusting the centre stop second Single step 1 x short A Continuous long A � Keep push-buttons A and B depressed 30 6 A Push-button A 8 7 � 4 5 chronograph hands are in their correct or incorrect zero position). 21 A simultaneously for at least 2 seconds (the centre stop-second rotates by 360° corrective mode is activated). � Adjusting the minute counter hand (position 9h) Single step 1 x short A Continuous long A � Returning the crown to position I 4 I III II Termination of the chronograph hands adjustment (can be carried out at any time). Push-button B Second hand 21 Setting the time � � 60 30 45 20 Setting the date (quick mode) 31 �* Pull out the crown to position III 45 20 I 2 3 II �* Push the crown back into position I. 45 � 15 10 30 9 10 1 I 2 3 8 7 6 5 II III 4 Crown � 60 30 45 Example: – Date / time on the watch: 17 / 1:25 AM 04 / 8:30 PM – Present date / time: 15 10 30 9 10 1 I 2 3 8 7 6 5 Please note: * In order to set the time to the exact second, � must be pulled out when the second hand is in position «60». Once the hour and minute hands have been set, � must be pushed back into position I at the exact second. II date 01 appears. � Push the crown back into position I. Please note: During the date changing phase between 9 PM and 12 PM; the date must be set to the date of the following day. 01 � 60 45 20 15 10 An extreme acceleration in setting the date with quick mode can induce a false date indication. The synchronization is re-established by setting the date from 01 till 31 (crown in position II). 30 9 10 1 I 2 3 8 7 6 II 4 5 Second hand 03 45 �**Pull out the crown to position III � 60 30 20 (the watch stops). 15 10 30 9 10 1 � Pull out the crown to position II 4 II 4 5 30 Setting the date/time following a battery change Date 17 20 6 time 8:45. 60 I 2 3 8 7 � Turn the crown until you reach the correct 21 20 9 10 1 III 4 30 continues to run). � Turn the crown until the correct 30 9 10 1 5 � Pull out the crown to position II (the watch � 15 10 30 6 � 60 30 (the watch stops). 15 10 8 7 Please note: * Following �, further intervals or intermediates can be displayed by pressing push-button B (display interval / make up measured time, ...) 30 9 10 1 � Pull out the crown to position III (all 3 4 second counter 20 15 10 Example: One or several chronograph hands are not in their correct zero positions and have to be adjusted (e.g. following a battery change). 60 30 20 Adjusting the chronograph hands to zero position Center stopsecond Minute counter 20 60 30 15 10 8 7 21 The three chronograph hands are returned to their zero positions. 60 30 20 2 3 8 7 6 (the watch continues to run). I 5 II �**Turn the crown until the correct date III 04 4 appears. �**Continue to turn the crown until the correct time 8:30 PM appears. � Turn the crown until yesterday’s date 03 60 30 45 20 � 15 10 2 3 6 5 4 04 appears 03 . � � 60 30 45 20 30 9 10 1 8 7 15 10 30 I II 9 10 1 2 3 8 7 6 5 4 �**Push the crown back into position I. I II III � Please note: **To set your watch to the exact second, please refer to the chapter entitled «setting the time». **Please observe the AM/PM clock rhythm. 11/2006 RONDA AG CH-4415 Lausen/Switzerland
