Download CB12 - Xantech.com
Transcript
INSTALLATION INSTRUCTIONS CB12 CONNECTING BLOCK • Output: 1 - Emitter "OUT" port (3.5mm mono mini jack). • Model 282, 283, 284 & 286 Xantech series Mini Emitters V G S 1 - Three terminal "VGS" block for wired connection of Xantech IR Receivers and SmartPad keypads. PWR OUT FEATURES AND SPECIFICATIONS • Inputs: 1 - "IR RCVR" 3.5mm stereo mini jack. Accepts any Xantech IR Receiver equipped with a 3.5mm stereo mini plug, such as the 291 series or 490-30. IR RCVR Fig. 1 Model CB12 Connecting Block may be used. • 2.1mm coaxial power jack for Xantech 781RG or 782-00 Power Supplies. • Dimensions: 2-1/8" x 1-1/4" x 3/4" CAUTION: Plug only Xantech IR Receivers equipped with a stereo mini plug into the IR RCVR jack. Do not plug emitters or other devices into this jack; to do so may damage emitters and power supplies! GND +12V +12 VDC Smart Pad™ IR OUT +12V IR OUT ROOM 3 780-10 ® J-BOX RECEIVER INSTALLATION 291 IR Receiver Fig. 2 illustrates a typical inHand Held stallation using the CB12 in a Remote multiroom IR repeater sysROOM 2 tem. In this case a Xantech 780-10 J-Box 781RG IR Receiver Satellite Receiver 291 Hidden Link™ IR Re7-Foot 3Power Supply Conductor Cable with ceiver is used to control a Quick Connect Mini Plug Satellite Receiver and a VCR To 120 V AC VCR in a cabinet behind closed (unswitched) doors in Room 1. Control of the same equipment is acModel 286M Dual Blink IR complished from two other Mouse Emitter rooms with a Xantech 780-10 IR RCVR J-box IR Receiver and a Equipment CB12 Connecting Block Smart Pad™ keypad, by usMounted Behind Closed Doors ing the 3-terminal "VGS" conROOM 1 nector on the CB12 Fig. 2 The CB12 in a Typical 3-Room IR Repeater System (V=+12Volts, G=Gnd., S=IR Signal). When connecting a system, follow this diagram carefully: IR OUT GND PWR OUT V G S GND 3-Conductor Room-to-Room Cable (unshielded OK) When you use more than 1 keypad and one IR receiver together in a system, use the high current power supply, model 782-00, in place of the 781RG. 1 Modules & Connecting Blocks The Model CB12 provides a low cost means of connecting Xantech "Quick Connect" IR Receivers and standard 3-wire IR Receivers to one single or one dual emitter and a power supply in an infrared repeater system. The OUT port can drive any of the Xantech emitter models in the 282, 283, 284 and 286 series as well as the 286M shown in Fig. 2.NOTE: Be sure the Power Supplies, in any of these systems, are plugged into an unswitched AC outlet. This maintains the system in "stand-by" operation so that power-on commands can be sent to the controlled equipment.INSTALLATION (cont'd) Fig. 3 illustrates another application of the CB12. In this case it serves as a "break-out" block for the convenient connection of a 291 IR Receiver to a 3-conductor room-to-room cable in a larger multiroom system. You may also use it with any other Xantech quick-connect IR Receiver, such as the 490-30, for the same purpose. INSTALLATION NOTES: 1. When used as a "break-out" block, you do not need to connect a power supply to the "PWR" jack on the CB12. Power is supplied on the 3-conductor cable coming from the connecting block in the equipment room. Also, do not plug an emitter into the "OUT" jack in this case. To do so will prevent operation of the emitters in the equipment room. 2. When paralleling IR receivers, a maximum of 12 is recommended. More than this may result in unreliable operation due to the buildup of IR noise. 3. The Smart Pad™ keypads may be paralleled in larger numbers. They are not subject to the IR noise limitation. 4. Mounting: The CB12 may be mounted on any flat surface using the double-sided adhesive tape supplied. ROOM 2 ROOM 3 ROOM 4 291 IR Receiver X J-BOX RECEIVER +12V X IR OUT CB12 PWR OUT Connecting Block +12 VDC 780-10 ® Hand Held Remote (See Text) 3-Wire Cable GND +12V 480-00 Dinky Link™ IR Receiver 780-10 J-Box IR Receiver Red Stripe IR OUT IR OUT GND GND IR RCVR Smart Pad™ Power Supply Connecting Block Mouse Emitter VCR EMITTERS IR IN Emitter AV Receiver 789-44 GND STATUS ® IR RCVR CONNECTING BLOCK 12VDC 282M +12 VDC 3-Conductor Room-to-Room Cable 24 to 18 gauge (unshielded OK) Satellite Receiver 282M 789-44 GND IR OUT +12V V G S To 120 V AC (unswitched) 782-00 283M Blink IR Emitter 286M 490-30 Series Micro Link™ IR Receivers Dual Blink IRs (to other controlled devices) MAIN ROOM 1, EQUIPMENT CABINET, ETC. Fig. 3 The CB12 used as a "Break-Out" Block NOTE: Be sure the power supplies, in any of these systems, are plugged into an un-switched AC outlet. This maintains the system in "stand-by" operation so that power-on commands can be sent to the controlled equipment. 8-30-00 2 CB12