Download Z8 Encore! XP F64XX Series Development Kit User Manual

Z8F64200100KITG
Z8 Encore! XP® F64XX Series
Development Kit
User Manual
UM015110-0508
Copyright ©2008 by Zilog®, Inc. All rights reserved.
www.zilog.com
Z8 Encore! XP® F64XX Series Development Kit
User Manual
ii
Revision History
Revision
Level
Description
Page
No
10
Added Z8F6423FT020 to Introduction section.
1
Removed Application Notes from Documentation
section.
3
March 2008 09
Changed document title to Z8 Encore! XP® F64XX
Series Development Kit User Manual.
All
November
2007
08
Replaced Z8 Encore!® with Z8 Encore! XP® and
Z8 Encore!® 64K Series MCUs with
Z8 Encore! XP® 64K Series Flash Microcontrollers
throughout the document.
All
November
2007
07
Replaced ZiLOG with Zilog. Updated Zilog logo.
Updated Documentation and MCU sections.
All
3, 7
December
2006
06
Changed Figure 1 to Figure 2.
6
July 2006
05
Added reference to USB Smart Cable.
1
November
2005
04
Removed the word Preliminary from all page footers All
and updated trademarks.
Date
May
2008
Revision History
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
iii
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System/Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Supported Host System Configuration . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
F64XX Series Development Board . . . . . . . . . . . . . . . . . . . . . . . . . 6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
IrDA Transceiver with Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . 9
External Interface Connectors JP1 and JP2 . . . . . . . . . . . . . . . 10
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table of Contents
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
1
Introduction
Zilog’s Z8 Encore! XP® F64XX Series MCUs are a part of the line of
Zilog® microcontroller products.
The Z8 Encore! XP F64XX Series Development Kit
(Z8F64200100KITG) allows you to get familiar with the hardware and
software tools available with this product. This kit consists of the
64 KB version of the Z8 Encore! XP Development Board that supports
and presents the features of the Z8 Encore! XP F64XX Series. The software development tool kit allows you to write application software and
contains all supporting documents.
Z8F6423FT020 is the silicon used in the board. For more details, refer to
Z8 Encore! XP® F64XX Series Product Specification (PS0199) available
for download at www.zilog.com.
This user manual acquaints you with the Z8 Encore! XP F64XX Series
Development Kit, and provides instructions on setting up and using the
tools to start building designs and applications.
Safeguards
The following precautions must be observed when working with the
devices described in this document.
Caution: Always use a grounding strap to prevent damage resulting from
electrostatic discharge (ESD).
Kit Contents
The Z8 Encore! XP F64XX Series Development Kit contains the
following hardware and software:
Introduction
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
2
Hardware
The hardware in Z8 Encore! XP F64XX Series Development Kit
includes:
•
•
•
Z8 Encore! XP Z8F642 Development Board
USB Smart Cable for PC to Z8 Encore! XP® Z8F642 development
board (Previous versions of the development kit used a serial smart
cable. Refer your original documentation for information on using the
serial smart cable).
5 V DC power supply
Packaging
CD-ROM Containing
Documentation
Power
Supply
Development
Board
Figure 1. Z8 Encore! XP MCU Development Kit Contents
(USB Smart Cable not shown)
Introduction
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
3
Software (on CD-ROM)
The software in Z8 Encore! XP F64XX Series Development Kit includes:
•
•
•
•
ZDS II - Z8 Encore! IDE with ANSI C-Compiler
Sample code
Document browser
Acrobat Reader
Documentation
•
Z8 Encore! XP® F64XX Series Development Kit Quick Start Guide
(QS0028)
•
Z8 Encore! XP Z8F642 technical documentation (on CD-ROM):
–
Z8 Encore! XP® F64XX Series Development Kit User Manual
(UM0151)
–
Zilog Developer Studio II - Z8 Encore!® User Manual (UM0130)
–
eZ8TM CPU User Manual (UM0128)
–
Z8 Encore! XP® F64XX Series Product Specification (PS0199)
–
–
Z8 Encore! XP® F64XX Series Product Brief (PB0124)
Programmer’s Reference Sheet
The sample code is installed with ZDS II and resides in the <installation directory>\samples folder.
The documentation can be installed with the DemoShield interface or can
be viewed on the CD-ROM using the DemoShield menus and a PDF
reader. A copy of the Acrobat installer is provided on the CD-ROM and
can be installed from the DemoShield install screen. After installing the
documentation Windows Explorer can be used to select any document to
be viewed with PDF file viewer.
Introduction
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
4
System/Software Requirements
IBM PC (or compatible computer) with the following minimum
configurations:
Supported Host System Configuration
Introduction
•
Win98 Second Edition/WinNT 4.0 Service Pack 6 (USB Smart Cable
not supported)/Win2000 Service Pack 4/Windows XP Professional
•
•
•
•
•
•
•
PentiumII/233 MHz processor or higher up to Pentium IV, 2.8 GHz
96 MB RAM or more
25 MB hard disk space or more (no documentation)
Super VGA video adapter
CD-ROM
One or more RS-232 communication ports
USB high-speed port (when using USB Smart Cable)
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
5
Installation
Refer to the directions provided in the Quick Start guide for software
installation and setup of the Z8 Encore! XP® F64XX Series development
kit.
Installation
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
6
F64XX Series Development Board
Introduction
The Z8 Encore! XP® F64XX Series development board is a development
and prototyping board for the Z8 Encore! XP Z8F642 microcontroller.
The board allows you to evaluate features of Z8 Encore! XP F64XX
Series and to develop an application before building the hardware.
TEST
U4
RESET
Y1
LEDs
JP1
P2
J2
P1 Console
J1
JP2
Figure 2. Z8 Encore! XP F64XX Series Development Board
F64XX Series Development Board
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
7
Features
The features of Z8 Encore! XP F64XX Series development board
includes:
•
•
•
•
•
•
•
•
•
•
•
Z8 Encore! XP MCU
3 LEDs
RS-232 interface (P1)
IrDA transceiver (U4)
Two pushbuttons, RESET and TEST
5 V DC power connector (J1)
On-Chip Debugger interface (P2)
Crystal Oscillator (Y1)
Header for Analog-to-Digital Converter (ADC) input (J2)
Prototyping area
External interface connectors JP1 and JP2 (not populated)
MCU
The Z8 Encore! XP Z8F642 MCU is member of a family of Zilog® microcontroller products based on Zilog’s 8-bit eZ8TM core CPU. The Flash
in-circuit programming capability allows for faster development time and
program changes in the field. The eZ8 core CPU is upward compatible
with existing Z8® instructions. The rich peripheral set of the
Z8 Encore! XP Z8F642 makes it suitable for various applications including motor control, security systems, home appliances, personal electronic
devices, and sensors.
F64XX Series Development Board
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
8
The development board contains circuitry to support and present all the
features of the Z8 Encore! XP® Z8F642. The main features of the
Z8 Encore! XP Z8F642 MCU are:
•
•
•
•
•
•
•
•
•
eZ8TM core CPU
•
•
•
•
•
•
•
•
Watchdog Timer (WDT) with internal RC oscillator
Up to 64 KB of Flash memory with in-circuit programming capability
Up to 4 KB of register RAM
Either eight or twelve channels, 10-bit ADC
Two Full-duplex UART
I2C interface (Master Mode only)
Serial Peripheral Interface (SPI)
Infrared Data Association (IrDA)-compliant infrared encoder/decoder
Three or four 16-bit timers with capture, compare, and PWM
capability
Thirty one, forty six or sixty I/O pins
Programmable priority interrupts
On-Chip Debugger (OCD)
Voltage Brownout Protection (VBO)
Power-on Reset (POR)
2.7 V to 3.6 V operating voltage with 5 V-tolerant inputs
Operating temperature: 20 °C ± 10 °C
For more information on the Z8 Encore! XP family of devices, refer to
Z8 Encore! XP® F64XX Series Product Specification (PS0199) available
for download at www.zilog.com.
F64XX Series Development Board
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
9
IrDA Transceiver with Endec
The Z8 Encore! XP® Z8F642 contains a fully-functional, high-performance UART with Infrared Encoder/Decoder (Endec). The Infrared
Endec is integrated with an on-chip UART to allow easy communication
between the Z8 Encore! XP Z8F642 and IrDA transceivers. Infrared communication provides secure, reliable, low-cost, point-to-point communication between PCs, PDAs, cell phones, printers and other infrared
enabled devices.
Power and Communication Interfaces
Table 1 provides jumper information concerning the shunt status,
functions and devices affected by selected jumpers.
Table 1. Jumpers JP3 and JP4
Device
Affected
Jumper
Status
Status
Default
JP3
OUT*
IrDA
interface
Enable
JP3
IN
IrDA
interface
Disable
X
JP4**
OUT*
RS-232
Enable
X
JP4
IN
RS-232
Disable
* These jumpers must not be OUT at the same time.
** If the module is plugged onto an eZ80® Development platform or eZ80
demonstration board the local RS-232 can be disabled by connecting header JP2
pin 50 to the corresponding GND on the mating connector.
F64XX Series Development Board
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
10
External Interface Connectors JP1 and JP2
The external interface connectors are not populated when the board is
shipped. You can insert 0.1" space headers of choice.
Note: Only Power and GND nets on connector JP1 are used on this module.
F64XX Series Development Board
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
11
Schematics
This section provides schematics for the Z8 Encore! XP® F64XX Series
Development Board.
Schematics
UM015110-0508
®
Z8 Encore! XP F64XX Series Development Kit
User Manual
12
5
4
3
2
1
VCC_33V
J1
2
3
1
F1
VCC_5V
U1
+ C2
C4
0.1uF
C3
0.1uF
100/10
U2
D
3
1
VIN VOUT
GND
VCC_33V
2
C7
0.1uF
VCC_33V
R1
LT1086-3.3/TO220
PA5_TXD0
+ C8
C9
PA5_TXD0
GND
680
2
C1+
4
C1-
C1
0.1uF
19
VCC_5V
RXE110
VCC
5V
PWR JACK
V+
GND
3
CONSOLE
P1
C5
0.1uF
5
C2+
6
C2-
13
T1IN
T1OUT
17
12
T2IN
T2OUT
8
15
R1OUT
R1IN
16
10
R2OUT
R2IN
9
V-
C6
0.1uF
1
6
2
7
3
8
4
9
5
TXD0
CTS0
RXD0
7
D
100/10
PA4_RXD0
3.3 OK
PA4_RXD0
1
1
20
GND
EN
SHDN
MAX3222
NC
NC
DB9 Female
USER
14
11
VCC_33V
GND
R2
10K
2
R17
10K
7
JP4
74LVC04/SO_1
R18
10K
U3C
5
6
R19
10K
U3D
9
8
11
U3E
U3F
14
R16
10K
14
1
U3A
14
-DIS_232
1
2
C
VCC_33V
14
C
14
10
13
12
GND
7
7
74LVC04/SO_1
7
74LVC04/SO_1
74LVC04/SO_1
74LVC04/SO_1
7
LED
GND
D1
PA3_CTS0
18
PA3_CTS0
2
0.1uF
DIS RS232
R3
D2
2
R4
R5
D3
1
PA1_T0OUT
R6
VCC_33V
2
68
GND
B
U4
2R7
100K
TEST
R8
10K
R9
D4
1
330nF
R7
100
YELL
PA2
SW1
100
GREEN
3
-DIS_IRDA
R10
4
VCC
1
LEDA
PA5_TXD0
2
TXD
IRDA_SD
4
SD
PA4_RXD0
3
RXD
6
GND
U3B
2
5
7
JP3
1
2
PC0_T1IN
74LVC04/SO_1
ZHX1810
0
GND
100
T
B
C10
VCC_33V
100
RED
14
1
PA0_T0IN
DIS IRDA
GND
R11 10K
1
2
3
4
5
A
1
2
3
4
5
VCC_33V
P2
VCC_33V
TP1
TP2
GND
GND
1
3
5
A
DBG
INTERFACE
2
4
6
DBG
DBG
Title
Encore! F642. Evaluation Module. Schematic.
Header 3x2
Size
B
Date:
5
4
3
2
Document Number
Rev
96C0918-001
Friday, June 06, 2003
Sheet
A
1
of
2
1
Figure 3. Z8 Encore! XP F64XX Series Development Board
Schematics
UM015110-0508
®
Z8 Encore! XP F64XX Series Development Kit
User Manual
13
5
4
3
2
1
PA2
connector 2
PA1_T0OUT
IO
IO
C13
0.1uF
AVDD
3
JP2
C12
2
D
AGND
PA0_T0IN
RESET
PA0_T0IN
PD2
PC2_SS
PF6
-RESET
SW2
Header 1
JP14
1
C15
0.001uF
1
Header 1
JP7
1
0.1uF
PF7
PF6
C19
0.001uF
Header 1
JP6
C16
C20
0.1uF
PF5
VCC_33V
PF5
PF4
PF3
PE4
PE3
GND
PE2
PE1
PE0
GND
PF2
PF1
PF0
VCC_33V
PD1_T3OUT
PD0_T3IN
XOUT
XIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
PA0/T0IN
PD2
PC2/SS
PF6
RESET
VDD
PF5
PF4
PF3
PE4
PE3
GND
PE2
PE1
PE0
GND
PF2
PF1
PF0
VDD
PD1/T3OUT
PD0/T3IN
XOUT
XIN
R12
220
PF4
PF3
18.432MHz
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
1
Header 1
JP10
1
DBG
PA5_TXD0
PA3_CTS0
PA4_RXD0
R13 100K
C23
18pF
PF2
18pF
C24
C17
0.1uF
PH1_ANA9
PB0_ANA0
PB1_ANA1
C28
0.001uF
PB4_ANA4
C29
0.001uF
1
C18
0.001uF
-RESET
VCC_33V
Header 1
JP17
PG3
VCC_33V
1
PB6_ANA6
PB7_ANA7
PB3_ANA3
PB2_ANA2
PH2_ANA10 PH3_ANA11
C31
0.001uF
C32
0.001uF
C33
0.001uF
C34
0.001uF
C35
0.001uF
C36
0.001uF
C21
0.1uF
1
C22
0.001uF
A
PG5
PG6
-DIS_232
-DIS_IRDA
NC
NC
JP1
1
Header 1
JP21
1
connector 1
for
reference
only
C37
0.001uF
C25
22uF
C38
0.01uF
26
24
22
20
18
16
14
12
10
8
6
4
2
4
GND
-DIS_IrDA
NC
GND
1
Header 1
JP20
1
3
-TRSTN
5
-F91_WE 7
GND
9
A6
11
A10
13
GND
15
A8
17
A13
19
A15
21
A18
23
A19
25
A2
27
A11
29
A4
31
A5
33
35
A21
37
A22
39
-CS0
41
-CS2
43
D1
45
D3
47
D5
49
D7
51
-MREQ 53
GND
55
-WR
57
-BUSACK 59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
VCC_33V
VCC_33V
A0
A3
VCC_33V
A7
A9
A14
A16
GND
A1
A12
A20
A17
-DIS_FLASH
VCC_33V
A23
-CS1
D0
D2
D4
GND
D6
-IOREQ
-RD
-INSTRD
-BUSREQ
B
HEADER 30x2/SM
A
Title
Encore! F642. Evaluation Module. Schematic.
Size
B
Date:
5
NC
NC
NC
NC
If Module is plugged onto the Dev Platform the local
RS232 interface is disabled by pin 50 of JP2
J2
25
23
21
19
17
15
13
11
9
7
5
3
1
NC
D
Header 1
JP19
AGND
PH0_ANA8
PH1_ANA9
PB0_ANA0
PB1_ANA1
PB4_ANA4
PB5_ANA5
PB6_ANA6
PB7_ANA7
PB3_ANA3
PB2_ANA2
PH2_ANA10
PH3_ANA11
VREF
NC
NC
GND
PC5_MISO
PC6_T2IN
PC2_SS
PA0_T0IN
PA1_T0OUT
PA2
PD6_CTS1
PD4_RXD1
PD0_T3IN
GND
PD2
PG0
PA5_TXD0
C
PG7
PB5_ANA5
NC
NC
PE6
PE4
PE2
PE0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
HEADER 30x2/SM
Z8F642
C30
0.001uF
NC
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
Header 1
JP18
PG4
+
C27
0.001uF
PA6_SCL
PA7_SDA
Header 1
JP16
Header 1
PF1
C26
0.001uF
GND
1
PG2
Header 1
PH0_ANA8
JP15
PG1
VREF
B
PA7_SDA
PD6_CTS1
PC3_SCK
PD7_RCOUT
PG0
GND
PG1
PG2
PE5
PE6
PE7
VCC_33V
PG3
PG4
PG5
PG6
VCC_33V
PG7
PC7_T2OUT
PC6_T2IN
DBG
PC1_T1OUT
PC0_T1IN
GND
GND
AVDD
PH0_ANA8
PH1_ANA9
PB0_ANA0
PB1_ANA1
PB4_ANA4
PB5_ANA5
PB6_ANA6
PB7_ANA7
PB3_ANA3
PB2_ANA2
PH2_ANA10
PH3_ANA11
VREF
AGND
Header 1
JP9
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
PC0_T1IN
Y1
Header 1
JP8
PA7/SDA
PD6/CTS1
PC3/SCK
PD7/RCOUT
PG0
GND
PG1
PG2
PE5
PE6
PE7
VDD
PG3
PG4
PG5
PG6
VDD
PG7
PC7/T2OUT
PC6/T2IN
DBG
PC1/T1OUT
PC0/T1IN
GND
GND
AVDD
PH0/ALG8
PH1/ALG9
PB0/ALG0
PB1/ALG1
PB4/ALG4
PB5/ALG5
PB6/ALG6
PB7/ALG7
PB3/ALG3
PB2/ALG2
PH2/ALG10
PH3/ALG11
VREF
AGND
1
C
DBG
PA5_TXD0
PA3_CTS0
PA4_RXD0
PA1/T0OUT
PA2
PA3/CTS0
GND
VDD
PF7
PC5/MISO
PD3
PD4/RXD1
PD5/TXD1
PC4/MOSI
VDD
GND
PA4/RXD0
PA5/TXD0
PA6/SCL
GND
JP13
0.1uF
EMI Filter
U6
GND
PE7
PE5
PE3
PE1
VCC_33V
PC4_MOSI
PC7_T2OUT
PC3_SCK
PC0_T1IN
GND
PC1_T1OUT
PD1_T3OUT
PD3
PD5_TXD1
PD7_RCOUT
PF0
PA3_CTS0
PA4_RXD0
C14
0.001uF
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
VCC_33V
GND
VCC_33V 1
C11
0.001uF
PA1_T0OUT
PA2
PA3_CTS0
GND
VCC_33V
PF7
PC5_MISO
PD3
PD4_RXD1
PD5_TXD1
PC4_MOSI
VCC_33V
GND
PA4_RXD0
PA5_TXD0
PA6_SCL
L1
3
2
Document Number
Rev
96C0918-001
Friday, June 06, 2003
A
Sheet
2
of
2
1
Figure 4. Z8 Encore! XP F64XX Series Development Board (Continued)
Schematics
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
14
Customer Support
For answers to technical questions about the product, documentation, or
any other issues with Zilog’s offerings, please visit Zilog’s Knowledge
Base at:
http://www.zilog.com/kb.
For any comments, detail technical questions, or reporting problems,
please visit Zilog’s Technical Support at:
http://support.zilog.com.
Customer Support
UM015110-0508
Z8 Encore! XP® F64XX Series Development Kit
User Manual
15
Warning: DO NOT USE IN LIFE SUPPORT
LIFE SUPPORT POLICY
ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant
into the body, or (b) support or sustain life and whose failure to perform when properly
used in accordance with instructions for use provided in the labeling can be reasonably
expected to result in a significant injury to the user. A critical component is any
component in a life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2008 by Zilog, Inc. All rights reserved. Information in this publication concerning the
devices, applications, or technology described is intended to suggest possible uses and
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The
information contained within this document has been verified according to the general
principles of electrical and mechanical engineering.
Z8, Z8 Encore!, eZ8, Z8 Encore! XP, Z8 Encore! MC, Crimzon, eZ80, and ZNEO are
trademarks or registered trademarks of Zilog, Inc. All other product or service names are
the property of their respective owners.
Disclaimer
UM015110-0508