Download Z8 Encore! 8K/4K MCU Evaluation Board User Manual - Digi-Key

Z8F08200100KIT
Z8 Encore!® 8K/4K MCU
Evaluation Kit
User Manual
UM015004-1105
ZiLOG Worldwide Headquarters • 532 Race Street • San Jose, CA 95126-3432
Telephone: 408.558.8500 • Fax: 408.558.8300 • www.ZiLOG.com
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
ii
This publication is subject to replacement by a later edition. To determine whether a later
edition exists, or to request copies of publications, contact:
ZiLOG Worldwide Headquarters
532 Race Street
San Jose, CA 95126-3432
Telephone: 408.558.8500
Fax: 408.558.8300
www.ZiLOG.com
Document Disclaimer
ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products
and/or service names mentioned herein may be trademarks of the companies with which they are associated.
©2005 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices,
applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG,
INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF
THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG
ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT
RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY
DESCRIBED HEREIN OR OTHERWISE. Except with the express written approval of ZiLOG, use of
information, devices, or technology as critical components of life support systems is not authorized. No
licenses are conveyed, implicitly or otherwise, by this document under any intellectual property rights.
Disclaimer
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
iii
Safeguards
The following precautions must be observed when working with the
devices described in this document.
Caution: Always use a grounding strap to prevent damage resulting from electrostatic discharge (ESD).
Revision History
Date
Revision
Level
Description
November 04
2005
Disclaimer
Page #
Removed the word Preliminary from all page footers and updated All
trademarks.
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
iv
Table of Contents
Safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
System/Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Supported Host System Configuration . . . . . . . . . . . . . . . . . . . . . . . .3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Z8 Encore! 8K/4K Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
UART with IrDA Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . .9
External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . . . . . . .10
Schematics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Table of Contents
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
v
List of Figures
Figure 1.
Figure 2.
Z8 Encore! MCU Evaluation Kit Contents . . . . . . . . . . . . . .2
Z8 Encore!® 8K/4K Evaluation Board . . . . . . . . . . . . . . . .6
List of Tables
Table 1.
List of Figures
Jumpers JP3 and JP4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
1
Introduction
The Z8 Encore!® 8K/4K MCU is the part of the line of ZiLOG microcontroller products.
The Z8 Encore! MCU Evaluation Kit (Z8F08200100KIT) enables users
to become familiar with the hardware and software tools available with
this product. This kit consists of the 8KB version of the Z8 Encore! evaluation board that supports and presents the features of the Z8 Encore! 8K/
4K. This kit allows users to begin writing application software and contains all supporting documents.
This manual acquaints users with the Z8 Encore! 8K/4K MCU Evaluation
Kit, and gives instructions on setting up and using the tools to start building designs and applications.
Kit Contents
The Z8 Encore!® 8K/4K MCU Evaluation Kit contains the following:
Hardware
Introduction
•
•
Z8 Encore!® 8K/4K Evaluation board
•
5VDC power supply
Smart Cable for PC to Z8 Encore! 8K/4K evaluation board (DB9 to
six-pin male)
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
2
Packaging
CD-ROM Containing
Documentation
Power
Supply
Smart Cable
Evaluation
Board
Figure 1. Z8 Encore! MCU Evaluation Kit Contents
Software (on CD-ROM)
•
•
•
•
ZDS II- Z8 Encore! IDE with ANSI C-Compiler
Sample code
Document browser
Acrobat Reader install program
Documentation
•
•
Introduction
Quick Start Guide
Registration card
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
3
•
Z8 Encore!® 8K/4K technical documentation (on CD-ROM)
– Evaluation Kit User Manual
– ZDS II - IDE User Manual
– eZ8 CPU User Manual
– Product Specification
– Product brief
– Application notes
– Programmer’s Reference Sheet
The sample code is installed with ZDS II and resides in the <installation directory>\samples in the user's disk drive.
The documentation can be installed by the user with the DemoShield
interface or can be viewed on the CD-ROM using the DemoShield menus
and a PDF reader. A copy of the Acrobat installer is provided on the CDROM and can be installed from the DemoShield install screen. After
installing the documentation on the user’s system Windows Explorer can
be used to select any document to be viewed with your favorite PDF file
viewer.
System/Software Requirements
IBM PC (or compatible computer) with the following minimum configurations:
Supported Host System Configuration
Introduction
•
Win98 Second Edition, WinNT 4.0 Service Pack 6, Win2000 Service
Pack 3, WinXP Service Pack 1
•
•
•
•
PentiumII/233MHz processor or higher up to Pentium IV, 2.8 GHz
96MB RAM or more
25MB hard disk space or more
Super VGA video adapter
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
4
•
•
Introduction
CD-ROM
One or more RS-232 communication ports
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
5
Installation
Follow the directions in the Quick Start Guide for software installation
and setup of the Z8 Encore! evaluation kit.
Installation
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
6
Z8 Encore! 8K/4K Evaluation Board
Introduction
The Z8 Encore! 8K/4K evaluation board is an evaluation and prototyping
board for the Z8 Encore! Z8 Encore! 8K/4K MCU. The board provides
customers with a tool to evaluate features of Z8 Encore! 8K/4K MCU,
and to start developing an application before building the hardware.
TEST
Y1
U6
RESET
P2
J2
LEDs
RS-232
Serial Port
J1
Figure 14. Z8 Encore!® 8K/4K Evaluation Board
Z8 Encore! 8K/4K Evaluation Board
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
7
Features
•
•
•
•
•
•
•
•
•
•
•
•
Z8 Encore!® MCU (28-pin SOIC)
3 LEDs
RS-232 interface
IrDA transceiver
Two pushbuttons, RESET and TEST
5VDC power connector
On-Chip Debugger interface
Crsytal Oscillator at 18.432MHz
Header for ADC input
Prototyping area
External interface connectors JP1 and JP2
2.7–3.6V operating voltage with 5V-tolerant inputs
MCU
The Z8 Encore!® 8K/4K MCU is member of a family of ZiLOG microcontroller products based upon the 8-bit eZ8 core CPU. The Flash in-circuit programming capability allows for faster development time and
program changes in the field. The eZ8 core CPU is upward compatible
with existing Z8® instructions. The rich peripheral set of the Z8 Encore!
8K/4K makes it suitable for a variety of applications including motor control, security systems, home appliances, personal electronic devices, and
sensors.
The evaluation board contains circuitry to support and present all the features of the Z8 Encore! 8K/4K. The main features of the Z8 Encore! 8K/
4K are:
Z8 Encore! 8K/4K Evaluation Board
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
8
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
eZ8 core CPU
8KB Flash memory with in-circuit programming capability
1KB register RAM
5-channel, 10-bit analog-to-digital converter (ADC)
Full-duplex UART
I2C interface (Master Mode only)
Serial Peripheral Interface (SPI)
Infrared Data Association (IrDA)-compliant infrared encoder/decoder
Two 16-bit timers with capture, compare, and PWM capability
Watch-Dog Timer (WDT) with internal RC oscillator
Eleven or nineteen I/O pins
Programmable priority interrupts
On-Chip Debugger
Voltage Brown-out Protection (VBO)
Power-On Reset (POR)
2.7–3.6V operating voltage with 5V-tolerant inputs
Operating temperatures: 20° ±10°C
For further information on the Z8 Encore!® family of devices, consult the
product specification, P/N PS0197, available for download from
www.zilog.com.
UART with IrDA Endec
The Z8 Encore! 8K/4K contains a fully-functional, high-performance
UART with Infrared Encoder/Decoder (ENDEC), component U6. The
Infrared Endec is integrated with an on-chip UART allowing easy com-
Z8 Encore! 8K/4K Evaluation Board
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
9
munication between the Z8 Encore! 8K/4K and IrDA transceivers. Infrared communication provides secure, reliable, low-cost, point-to-point
communication between PCs, PDAs, cell phones, printers and other infrared enabled devices.
Crystal Oscillator
The evaluation board ships with an 18.432MHz Crystal Oscillator (Y1).
If you want to change the change the Crystal Oscillator you are required
to change the Clock Frequency in for ZDSII. The frequency settings can
be found at Project > Settings > Debugger > ZDB: Configure ZDB Driver: Clock
Frequency. See the Z8Encore! Product Speciification for supported frequencies.
Power and Communication Interfaces
Table 1 provides jumper information concerning the shunt status, functions, devices and defaults affected of jumpers JP3 and JP4.
Table 1. Jumpers JP3 and JP4
Jumper
Status
JP3**
OUT*
JP3
Device
Affected
Status
Default
RS-232
interface
Enabled
X
IN
RS-232
interface
Disabled
JP4
OUT*
IrDA interface Enabled
JP4
IN
IrDA interface Disabled
X
Note: * These jumpers must not be OUT at the same time
Note: ** If the module is plugged onto an eZ80 Evaluation platform or eZ80
demonstration board the local RS-232 can be disabled by connecting header JP2
pin 50 to the corresponding GND on the mating connector
Z8 Encore! 8K/4K Evaluation Board
UM015004-1105
Z8 Encore!® 8K/4K MCU
Evaluation Kit User Manual
10
External Interface Headers JP1 and JP2
The external interface headers, JP1 and JP2 contain no connectors when
the board is shipped. The user can insert 0.1" space connectors of choice.
Z8 Encore! 8K/4K Evaluation Board
UM015004-1105
Z8 Encore!® Evaluation Kit
User Manual
11
Schematics
This section includes schematics for the the Z8 Encore!® 8K/4K Evaluation Board.
Schematics
UM015004-1105
Z8 Encore! ® 8K/4K MCU
Evaluation Kit User Manual
12
VCC_33V
VCC_33V
VCC_33V
connector 2
GND
GND
C12
22uF
+
C13
0.01uF
JP2
GND
VCC_33V
PC4_MOSI
D2
PA0_T0IN
1
2
100
RED
R9
D3
PA1_T0OUT
PC3_SCK
PC0_T1IN
GND
PC1_T1OUT
R8
1
R10
SW2
VCC_33V
2
GND
100
GREEN
TEST
100K
GND
R11
D4
PA2
PA3_CTS0
PA4_RXD0
1
PA6_SCL
PA7_SDA
2
YELL
C4
100
R12
-RESET
VCC_33V
100
0.1uF
VCC_33V
U7
PA6_SCL
PA7_SDA
-RESET
GND
XIN
XOUT
VCC_33V
PA0_T0IN
PA1_T0OUT
PA2
1
2
3
4
5
6
7
8
9
10
20 pin Socket
PA6/SCL
PA7/SDA
RESET
GND
XIN
XOUT
VDD
PA0/T0IN
PA1/T0OUT
PA2/DE
U8
PC0/T1IN
PB0/ANA0
PB1/ANA1
VREF
AGND
AVDD
DBG
PA5/TXD0
PA4/RXD0
PA3/CTS0
20
19
18
17
16
15
14
13
12
11
PC0_T1IN
PB0_ANA0
PB1_ANA1
VREF
AGND
VCC_33V
DBG
PA5_TXD0
PA4_RXD0
PA3_CTS0
PC0_T1IN
PA6_SCL
PA7_SDA
-RESET
GND
XIN
XOUT
VCC_33V
PC5_MISO
PC4_MOSI
PC3_SCK
PC2_SS
PA0_T0IN
PA1_T0OUT
Z8F0xx1
VCC_33V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28 pin Socket
PC0/T1IN
PA6/SCL
PA7/SDA
RESET
VSS
XIN
XOUT
VDD
PC5/MISO
PC4/MOSI
PC3/SCK
PC2/SS
PA0/T0IN
PA1/T0OUT
PB0/ANA0
PB1/ANA1
PB2/ANA2
PB3/ANA3
PB4/ANA4
VREF
AVSS
AVDD
DBG
PC1/T1OUT
PA5/TXD0
PA4/RXD0
PA3/CTS0
PA2/DE
28
27
26
25
24
23
22
21
20
19
18
17
16
15
PB0_ANA0
PB1_ANA1
PB2_ANA2
PB3_ANA3
PB4_ANA4
VREF
AGND
VCC_33V
DBG
PC1_T1OUT
PA5_TXD0
PA4_RXD0
PA3_CTS0
PA2
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
GND
PC5_MISO
PC2_SS
PA0_T0IN
PA1_T0OUT
PA2
GND
PA5_TXD0
GND
-DIS_IrDA
If Module is plugged onto the Dev Platform the local
-DIS_232 RS232 interface is disabled by pin 50 of JP2
-DIS_IRDA
GND
HEADER 30x2/SM
connector 1
for
reference
only
JP1
DBG
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
A21
37
A22
39
-CS0
41
-CS2
43
D1
45
D3
47
D5
49
D7
51
-MREQ 53
GND
55
-WR
57
-BUSACK 59
-TRSTN
-F91_WE
GND
A6
A10
GND
A8
A13
A15
A18
A19
A2
A11
A4
A5
Z8F0XX2
R3
10K
RESET
-RESET
DBG
PA5_TXD0
PA3_CTS0
PA4_RXD0
-RESET
SW1
XIN
XOUT
C10
0.01uF
VREF
R13
220
Y1
18.432MHz
R14
PB0_ANA0
100K
C15
18pF
18pF
C16
DBG
PA5_TXD0
PA3_CTS0
PA4_RXD0
PB1_ANA1
PB2_ANA2
PB3_ANA3
PB4_ANA4
+
C17
0.001uF
C18
0.001uF
C19
0.001uF
C20
0.001uF
C21
0.001uF
AGND
C14
22uF
C22
0.01uF
PB0_ANA0
PB1_ANA1
PB2_ANA2
PB3_ANA3
PB4_ANA4
J2
1
3
5
7
9
2
4
6
8
10
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
VCC_33V
VCC_33V
A0
A3
VCC_33V
A7
A9
A14
A16
GND
A1
A12
A20
A17
-DIS_FLASH
VCC_33V
A23
-CS1
D0
D2
D4
GND
D6
-IOREQ
-RD
-INSTRD
-BUSREQ
Header 5x2
HEADER 30x2/SM
Title
Schematic, Z8 Encore! ® 8K/4K MCU Evaluation Board, Page 1 of 2
Appendix
UM015004-1105
Z8 Encore! ® 8K/4K MCU
Evaluation Kit User Manual
13
VCC_33V
J1
PWR JACK
5V
VCC
RXE110
VCC
U10
+ C1
C23
0.1uF
C3
0.1uF
100/10
U2
3
1
VCC_33V
2
VIN VOUT
GND
PA5_TXD0
+ C8
C9
C5
0.1uF
VCC_33V
R1
LT1086-3.3/TO220
19
F1
PA5_TXD0
GND
680
2
C1+
4
C1-
VCC
2
3
1
V+
3
CONSOLE
P1
GND
C7
0.1uF
5
C2+
6
C2-
13
T1IN
T1OUT
17
12
T2IN
T2OUT
8
15
R1OUT
R1IN
16
10
R2OUT
R2IN
9
V-
C6
0.1uF
1
6
2
7
3
8
4
9
5
TXD0
CTS0
RXD0
7
100/10
LED
3.3 OK
PA4_RXD0
PA4_RXD0
1
1
20
GND
EN
GND
D1
SHDN
MAX3222
NC
NC
DB9 Female
USER
14
11
18
PA3_CTS0
PA3_CTS0
2
0.1uF
VCC_33V
GND
14
R15
10K
U4A
74LVC04/SO
1
JP3
1
2
2
7
-DIS_232
GND
DIS RS232
R5
C11
VCC_33V
68
330nF
R6
14
R4
10K
U4B
PA5_TXD0
74LVC04/SO
3
-DIS_IRDA
IRDA_SD
4
PA4_RXD0
5
VCC
1
LEDA
2
TXD
4
SD
3
RXD
6
GND
7
JP4
1
2
T
U6
2R7
ZHX1810
0
GND
DIS IRDA
GND
TP1
GND
R7
10K
1
2
3
4
5
1
2
3
4
5
VCC_33V
TP2
P2
VCC_33V
GND
1
3
5
DBG
INTERFACE
2
4
6
-RESET
DBG
-RESET
DBG
Title
Encore! F08. Evaluation Module. Schemat
Header 3x2
Size
B
Document Number
96C0897-001
®
Schematic, Z8 Encore! 8K/4K Evaluation Board Page 2 of 2
Appendix
UM015004-1105