Download SDC200/RDS - RVR Elettronica SpA Documentation Server
Transcript
SDC200/RDS USER MANUAL Manufactured by R.V.R ELETTRONICA S.p.A. Italy File Name: SDC200_RDS_ING_1.1.indb Version: 1.1 Date: 04/07/2012 Revision History Date Version 29/11/2011 1.0 04/07/2012 1.1 Reason First Version Update of coder input section Editor J. H. Berti J. H. Berti SDC200/RDS - User Manual Version 1.1 © Copyright 2011-2012 R.V.R. Elettronica SpA Via del Fonditore 2/2c - 40138 - Bologna (Italia) Telephone: +39 051 6010506 Fax: +39 051 6011104 Email: [email protected] Web: www.rvr.it All rights reserved. Printed and bound in Italy. No part of this manual may be reproduced, memorized or transmitted in any form or by any means, electronic or mechanic, including photocopying, recording or by any information storage and retrieval system, without written permission of the copyright owner. Declaration of Conformity Hereby, R.V.R. Elettronica SpA, declares that this FM transmitter is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. SDC200/RDS ELETTRONICA Table of Contents 1. 2. 3. 3.1 3.2 4. 4.1 4.2 4.3 4.4 4.5 4.6 5. 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 Preliminary Instructions Warranty First Aid Electric shock treatment Treatment of electric burns General Description Unpacking Features Frontal Panel Description Rear Panel Description Connectors Description Technical Description Software Description Symbology Guide Visualization of levels and Main Menu CLIPPER and AGC - ON/OFF CODER - Selection of preemphasis CODER - Selection of mono/stereo CODER - Modification of pilot tone level AGC - Adjusment of parameters CODER INPUT - Selection of Analogic / Digital ANALOGICAL INPUTS - Adjustment of levels DIGITAL INPUTS - Adjustment of levels INPUT SELECTION AND RESCUE SYSTEM RESCUE SYSTEM - Time and level adjustment RESCUE SYSTEM - RDS Activation / Deactivation ANALOGICAL OUTPUT - Adjustment of audio level RDS – Carrier Activation / Deactivation RDS – Adjustment of carrier level RDS – Adjustment of clock time RDS – Selection of DSN RDS – Selection of PSN RDS - Entering or editing of the PS in Main PSN RDS - Entering or editing of the DI in Main PSN RDS - Entering or editing of the PI in Main PSN RDS - Entering or editing of the TA, TP and MS in Main PSN RDS - Entering or editing PTYN in Main PSN RDS - Insertion of Alternative Frequencies RDS - Radio Text entry User Manual Rev. 1.0 - 04/07/12 1 1 2 2 2 3 3 3 7 7 8 9 10 10 11 12 13 14 15 16 17 18 19 20 22 24 25 26 27 28 30 31 32 34 35 38 39 41 43 SDC200/RDS 5.27 5.28 5.29 5.30 5.31 6. 6.1 ii ELETTRONICA RDS - Block Custom Messages entry RDS - Scrolling Custom Messages entry RS232 - COM1, COM2 and COM3 Serial Configuration User PASSWORD - First entry User PASSWORD - Forgotten Password Recovery Identification of the Modules Upper View Rev. 1.1 - 04/07/12 45 47 49 50 52 53 53 User Manual SDC200/RDS ELETTRONICA IMPORTANT The symbol of lightning inside a triangle placed on the product, evidences the operations for which is necessary gave it full attention to avoid risk of electric shocks. The symbol of exclamation mark inside a triangle placed on the product, informs the user about the presence of instructions inside the manual that accompanies the equipment, important for the efficacy and the maintenance (repairs). 1. Preliminary Instructions • General Warnings This equipment should only be operated, installed and maintained by “trained” or “qualified” personnel who are familiar with risks involved in working on electric and electronic circuits. “Trained” means personnel who have technical knowledge of equipment operation and who are responsible for their own safety and that of other unqualified personnel placed under their supervision when working on the equipment. “Qualified” means personnel who are trained in and experienced with equipment operation and who are responsible for their own safety and that of other unqualified personnel placed under their supervision when working on the equipment. WARNING: Residual voltage may be present inside the equipment even when the ON/OFF switch is set to Off. Before servicing the equipment, disconnect the power cord or switch off the main power panel and make sure the safety earth connection is connected. Some service situations may require inspecting the equipment with live circuits. Only trained and qualified personnel may work on the equipment live and shall be assisted by a trained person who shall keep ready to disconnect power supply at need. R.V.R. Elettronica S.p.A. shall not be liable for injury to persons or damage to property resulting from improper use or operation by trained/untrained and qualified/unqualified persons. WARNING: The equipment is not water resistant. Any water entering the enclosure might impair proper operation. To prevent the risk of electrical shock or fire, do not expose this equipment to rain, dripping or moisture. Please observe local codes and fire prevention rules when installing and operating this equipment. WARNING: This equipment contains exposed live parts involving an electrical shock hazard. Always disconnect power supply before removing any covers or other parts of the equipment. Ventilation slits and holes are provided to ensure reliable operation and prevent overheating; do not obstruct or cover these slits. Do not obstruct the ventilation slits under any circumstances. The product must not be incorporated in a rack unless adequate ventilation is provided or the manufacturer’s instructions are followed closely. WA R N I N G : T h i s e q u i p m e n t c a n r a d i a t e radiofrequency energy and, if not installed in compliance with manual instructions and applicable regulations, may cause interference with radio communications. User Manual WARNING: This equipment is fitted with earth connections both in the power cord and for the chassis. Make sure both are properly connected. Operation of this equipment in a residential area may cause radio interference, in which case the user may be required to take adequate measures. The specifications and data contained herein are provided for information only and are subject to changes without prior notice. R.V.R. Elettronica S.p.A. disclaims all warranties, express or implied.While R.V.R. Elettronica S.p.A. attempts to provide accurate information, it cannot accept responsibility or liability for any errors or inaccuracies in this manual, including the products and the software described herein. R.V.R. Elettronica S.p.A. reserves the right to make changes to equipment design and/or specifications and to this manual at any time without prior notice. • Notice concerning product intended purpose and use limitations. This product is a radio transmitter suitable for frequencymodulation audio radio broadcasting. Its operating frequencies are not harmonised in designated user countries. Before operating this equipment, user must obtain a licence to use radio spectrum from the competent authority in the designated user country. Operating frequency, transmitter power and other characteristics of the transmission system are subject to restrictions as specified in the licence. 2. Warranty La R.V.R. Elettronica S.p.A. warrants this product to be free from defects in workmanship and its proper operation subject to the limitations set forth in the supplied Terms and Conditions. Please read the Terms and Conditions carefully, as purchase of the product or acceptance of the order acknowledgement imply acceptance of the Terms and Conditions. For the latest updated terms and conditions, please visit our web site at WWW.RVR.IT. The web site may be modified, removed or updated for any reason whatsoever without prior notice. The warranty will become null and void in the event the product enclosure is opened, the product is physically damaged, is repaired by unauthorised persons or is used for purposes other than its intended use, as well as in the event of improper use, unauthorised changes or neglect. In the event a defect is found, follow this procedure: 1 Contact the seller or distributor who sold the equipment; provide a description of the problem or malfunction for the event a quick fix is available. Sellers and Distributors can provide the necessary information to troubleshoot the most frequently encountered problems. Normally, Sellers and Distributors can offer a faster repair service than the Manufacturer would. Please note that Sellers can pinpoint problems due to wrong installation. 2 If your Seller cannot help you, contact R.V.R. Elettronica S.p.A. and describe the problem; if our staff deems it appropriate, you will receive an authorisation to return the equipment along with suitable instructions; 3 When you have received the authorisation, you may return the unit. Pack the unit carefully before shipment; use the original packaging whenever possible and seal the package perfectly. The customer bears all risks of loss (i.e., R.V.R. shall not be liable for loss or damage) until the package reaches the R.V.R. factory. For this Rev. 1.1 - 04/07/12 / 54 SDC200/RDS 4 ELETTRONICA reason, we recommend insuring the goods for their full value. Returns must be sent on a C.I.F. basis (PREPAID) to the address stated on the authorisation as specified by the R.V.R. Service Manager. • One rescuer: give 2 quick rescue breaths after each 15 compressions. • Units returned without a return authorisation may be rejected and sent back to the sender. Two rescuers: one rescue breath after each 5 compressions. • Do not stop chest compressions while giving artificial breathing. • Call for medical help as soon as possible. Be sure to include a detailed report mentioning all problems you have found and copy of your original invoice (to show when the warranty period began) with the shipment. 3.1.2 Please send spare and warranty replacement parts orders to the address provided below. Make sure to specify equipment model and serial number, as well as part description and quantity. R.V.R. Elettronica S.p.A. Via del Fonditore, 2/2c 40138 BOLOGNA ITALY Tel. +39 051 6010506 3. First Aid Electric shock treatment 3.1.1 If the victim is unconscious Lay the victim down on his/her back on a firm surface. • the neck and tilt the head backwards to free the airway system (Figure 1). Cover victim with a blanket. • Try to reassure the victim. • Loosen the victim’s clothing and have him/her lie down. • Call for medical help as soon as possible. Treatment of electric burns 3.2.1 Large burns and broken skin Follow the first aid procedures outlined below. • • 3.2 All personnel engaged in equipment installation, operation and maintenance must be familiar with first aid procedures and routines. 3.1 If the victim is conscious • Cover affected area with a clean cloth or linen. • Do not break any blisters that have formed; remove any clothing or fabric that is stuck to the skin; apply adequate ointment. • Administer adequate treatment for the type of accident. • Get the victim to a hospital as quickly as possible. • Elevate arms and legs if injured. If medical help is not available within an hour, the victim is conscious and is not retching, administer a solution of table salt and baking soda (one teaspoon of table salt to half teaspoon of baking soda every 250 ml of water). Have the victim slowly drink half a glass of solution for four times during a period of 15 minutes. Stop at the first sign of retching. Do not administer alcoholic beverages. Figure 1 • If needed, open the victim’s mouth and check for breathing. • If there is no breathing, start artificial respiration without delay (Figure 2) as follows: tilt the head backwards, pinch the nostrils, seal your mouth around the victim’s mouth and give four fast rescue breaths. 3.2.2 Minor burns • Apply cold (not ice cold) strips of gauze or dress wound with clean cloth. • Do not break any blisters that have formed; remove any clothing or fabric that is stuck to the skin; apply adequate ointment. • If needed, have the victim change into clean, dry clothing. • Administer adequate treatment for the type of accident. • Get the victim to a hospital as quickly as possible. • Elevate arms and legs if injured. Figure 2 • Check for heartbeat (Figure 3); if there is no heartbeat, begin chest compressions immediately (Figure 4) placing your hands in the centre of the victim’s chest (Figure 5). Figure 3 / 54 Figure 4 Figure 5 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 4. General Description The SDC200/RDS, manufactured by R.V.R. Elettronica SpA, is a RDS + Stereo Coder model with display. The SDC200/RDS are designed to being contained into a 19” rack box of 1HE. 4.1 Unpacking The package contains: 1 SDC200/RDS 1 User Manual 1 Mains power cable The following accessories are also available from Your R.V.R. Dealer: • 4.2 Accessories, spare parts and cables Features Il SDC200/RDS is fully digital, it use only high quality components like A/D and D/A 24 bit converters and numerical processing (DSP) at 32 bit. The input section includes XLR (R&L) and analogical BNC, as well as the optical and coaxial digital inputs. It is present a rescue system for R&L and MPX audio inputs (changeover). The stereo coding is realized digitally, as well as the low-pass filters and the preemphasis. The RDS coder manages n. 6 data set and dynamic services TMC, TDC, IH and EWS. All functioning and programming parameters are managed through dedicated software. The equipment firmware can be updated through serial port without the need of hardware settings and without interruption of the service. User Manual Rev. 1.1 - 04/07/12 / 54 SDC200/RDS ELETTRONICA Two major features of SDC200/RDS are compact design and userfriendliness. Design is based on a modular concept: the different functions are performed by modules that, for the most part, are connected through male and facilitates maintenance and module replacement. This Stereo Coder uses a frequency sinthesized internal digital circuitry that allows very linear modulation, high stereo separation, high input level capability. The input/output analog section of good quality integrates oneself with digital system answering for high input dynamics, high signal/noise rate and very low distorsion. 4.2.1 RDS System Description The Radio-Data-System is proper for the transmission of information in mono/ stereo programs of VHF/MF (87.5-108 Mhz). It satisfies the requested requirements to the transmission of supplementary data on radio programs: 1) Compatibility with the current mono/stereo transmissions; 2) Absence of interferences towards the adjacent programs; 3) Compatibility with other identification systems which are already working. The system, selected by an international specialistic team, allows the data transmission at a speed of 1187.5 bit/sec with phase modulation at two levels , carrier wave 57 Mhz and range ±2 Khz. The broadcasted binary signal is in advance put out on a differential codification. The registry of transmission is at packages of lenght 104 bits (87.6 ms) named GROUPS, each of them composed of 4 blocks of 26 bits. Every block is composed of 16 bits of information and of 10 bits of protection, which are properly studied to allow the recovery of an erroneous word with a maximum of 5 wrong bits. They are provided with 16 separete blocks of which 6 are still not defined; every group begins with a PI identification code (Program Identification) which has the double intent to synchronize the receiver and to identify the channel which transmits the signal. The pourpose of the encoder SDC200/RDS is to manage the principal services defined by the standard CENELEC EN 50067 as: PI, PS, PTY, TP, AF, TA, DI, M/S, PIN, RT, EON, TDC, IH, CT. / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA As follows, we’ll mention a short description about the function of each of these services. PI - PROGRAM IDENTIFICATION: it’s the identification code of the radio. Its more important application is to allow the receiver, in case of bad reception, to implement the “Automatic Frequency Change”; this happens when there is a signal with the same PI and of better level than the syntonized one. PS - PROGRAM SERVICE: it’s the visualized text on the receiver display, which has to be of maximum 8 characters, as this is the standard dimension of receivers displays. The SDC200/RDS characteristic is to store up to 8 messages and the time of transmission of each of them. Every message can be composed from 1 to 16 words of 8 characters, and it’s possible to select the permanence time on the display of each of the 16 separate words. PTY - PROGRAM TYPE: it’s the identification of the “Program Type” which is on air (example News, Sport, Rock, etc.) It’s used to qualify on the receiver the automatical research of the program type desired. TP - TRAFFIC PROGRAM IDENTIFICATION: this service indicates with a signal on the receiver display that the program we’re receiving includes traffic news. AF - ALTERNATIVE FREQUENCIES: it’s the frequencies list of different transmitters which transmit the same program in the adjacent receiving areas. The list is memorized by the receiver and used to reduce the commutation time beetwen the different transmitters of the same program. TA - TRAFFIC-ANNOUNCEMENT IDENTIFICATION: it’ used to indicate to the car-driver that the traffic news are on air. The receiver could use the signal in one of the following modes: a) To switch automatically from the Tape (or from the Compact Disk) to the radio; b) To automatically switch on the radio when the traffic news begin; c) To automatically change over from a station which doesn’t transmit traffic news. M/S - MUSIC/SPEECH SWITCH: it’s used to modify the music and the spoken volume one by one. PIN - PROGRAM- ITEM NUMBER: it’s used to plan the receiver to receive certain programs at preselected date and hour. RT - RADIOTEXT: it’s used to transmit the text trasmission; this function is mainly for the domestic application (house receivers). User Manual Rev. 1.1 - 04/07/12 / 54 SDC200/RDS ELETTRONICA EON - ENHANCED OTHER NETWORKS: it’s used to transmit the PI,PS,AF,PTY to the PIN of other radios. TDC - TRANSPARENT DATA CHANNEL: it’s used for the data transmission and it could be free used, for example, to send messages on a brighltly sign. IH - IN HOUSE APPLICATION: it’s used to transmit data of exclusive use of the broadcaster and it can be utilized , for example, to send telemetry data, software, etc... / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 4.3 Frontal Panel Description [1] [2] [3] [4] 4.4 DISPLAY ENCODER USB RS232 Liquid Crystal Display Knob and button to control the software USB/B port RS232 serial port Rear Panel Description [1] ON/OFF [2] PLUG & A.C. LINE FUSE [3] EARTH [4] RS232 1 [5] RS232 2 [6] OUT.2 [7] OUT.1 [8] MPX [9] PILOTE [10] LEFT/Mono 2 [11] RIGHT/Mono 1 [12] DIGITAL INPUT 2 [13] DIGITAL INPUT 1 User Manual Green bright power switch Power supply socket, 110-230V 50-60Hz and fuse block. Use a small screwdriver to remove the block and replace with 250mA delayed fuses Ground clamp RS32 serial port, DB9 female connector RS32 serial port, DB9 female connector Analogical output 2 , BNC connector Analogical output 1 , BNC connector MPX analogic input connector, BNC type PILOT TONE analogic input connector, BNC type Balanced analogical audio input, 3 poles XLR connector Balanced analogical audio input, 3 poles XLR connector TOS-LINK digital optical input Unbalanced coaxial digital input, PIN-RCA connector Rev. 1.1 - 04/07/12 / 54 SDC200/RDS 4.5 4.5.1 ELETTRONICA Connectors Description RS232 Type: DB9 Female 1 2 3 4 5 6 7 8 9 NC TX_D RX_D NC GND +12V NC CTS NC NOTE: Normally, the SDC200/RDS is configured as DCE (Data Communication Equipment) for serial communications. 4.5.2 DIGITAL INPUT 2 4.5.3 DIGITAL INPUT 1 Type: TOS-LINK Female Type: RCA Female 1 2 4.5.4 LEFT/Mono 2 & RIGHT/Mono 1 Type: XLR Female 1 2 3 / 54 GND Positive GND Positive Negative Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 4.6 Technical Description Parameters SDC200/RDS User Interface Primary Power Phisical Dimensions (W x H x D) Weight Environmental working temperature ANALOGUE AUDIO INPUTS Conversion LCD - 2 x 40 with Encoder 115 - 230 VAC ±10% 483 x 44 x 280 mm 3,5 kg -10 to + 40 °C GENERALS Connector Impedance Input level Maximum input level PILOTE INPUTS Connector Pilot frequency synch. Input level DIGITAL AUDIO INPUTS Connector Data format Sampling frequency ANALOGUE MPX INPUTS Connector Impedance Input level Maximum input level OUTPUTS 1 & 2 D/A converter Connector Impedance Output level Maximum Output level STEREO CODER OPERATION Pilot Tone Pilot frequency level Pilot frequency phase Attenuation with 38 KHz suppressed carrier noise MPX output Preemphasis Preemphasis linearity + Low-Pass 15 KHz low-pass filter Low-pass filter 19 KHz attenuation Clipper Limiter AGC Stereo S/N FM Ratio Total Harmonic Distortion Intermodulation distortion Stereo separation RDS OPERATION Standards Command formats Static services Dynamic service RDS Groups Data Set RDS MODULATION Subcarrier frequency Bandwidth Synchronisation RDS phase adjustment ELABORATION A/D conversion D/A conversion DSP elaboration OTHER CONNECTORS Serial port User Manual 24 Bit XLR 3P. Fem. Balanced 600ohm/10 kohm -12dBu to +12dBu - step 0,1dB (Adj.-Sw) +16dBu BNC unbalanced 19KHz +/- 2Hz -30 / +12dBu (Sinusoid. o TTL) Optical TOS-LINK + Pin RCA AES/EBU - S/PDIF - EIAJ340 32 to 96KHz BNC unbalanced 10 Kohm Gain 0dB / Out.MPX +20dBu 24 bit BNC unbalanced 50 ohm -12dBu to +12dBu - step 0,1dB (Adj - Sw) (Gain0dB / inp.MPX) +20dBu 19 KHz ±0.1 Hz -8dBu to -32 dBu - step 0,1 dB - 12° to +12° - 0.1° step min. -90 dB -90 dBu 50/75 microsec. From 30 Hz to 15 KHz ±0.15 dB Ripple from 30 HZ to 15 KHz ±0.1 dB Min. -56 dB Right and Left Channel Right and Left Channel > 81 dB RMS (typical 84dB) < 0.05% 30 Hz ÷ 15 kHz ≤ 0.03% with 1 kHz and 1,3 kHz tones 68 dB, 30 Hz to 15 kHz Cenelec 50067 Specification UECP - SPB490 Ver.6.1 / 2003 DI,PI,M/S,TP,TA,TP,TPY,RT,CT, AF,PIN,EON,PSN TMC,TDC,EWS,IH 0A, 1A, 2A, 3A, 5A, 6A, 8A, 9A, 14A N° 6 57 KHz ±1.5 Hz +/- 2,4KHz (-50dB) Internal / external Adjustable up to 360 degrees in 0.33-degree increments 24 bit (Dynamic range 105dB) 24 bit (Dynamic range 123dB) 32 bit, fixed point Rev. 1.1 - 04/07/12 3 RS232 DB9 Connector., (1 USB Optional) / 54 SDC200/RDS ELETTRONICA 5. Software Description 5.1 Symbology Guide S D C 2 0 0 R V R S D C L - 0 0 0 1 0 4 EN T ER R uo tare En c o der [ BACK ] 10 / 54 [ B A C K ] EN T ER Indic ates the reques t of a pres s ure on enc oder to proc eed in the c onfirm ation of param eter or to a page s hift. R O TA TIO N Indic ates the reques t of a rotation on enc oder to proc eed in the variations of param eter or vis ualiz ation. The bold font indic ates that the flas hing field is ready for for editing or c onfirm ation. Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 5.2 Visualization of levels and Main Menu S D C 2 0 0 R V R [ S D C L - 0 0 0 1 0 4 B A C K EN T ER P res s enter to ac c es s the dis play of levels and the M ain M enu. O U T - 1 [ - 2 0 . 0 0 ] || || || || || || || || || || || || || || : O U T - 2 [ - 2 0 . 0 0 ] || || || || || || || || || || || || || || : I - M P X [ < - 3 5 . 0 0 ] || || || || || || : AG C _ X [ | [ A U D I O 0 . 0 0 ] M e n u : ] [ R D S } [ EN T ER { M a i n [ A U D I O { M a i n [ A U D I O R D S ] [ R D S B A C K ] [ S Y S T EM ] [ C LO C K M e n u : } [ B A C K ] [ S Y S T EM ] [ C LO C K : R o tate En c o der ] [ ] [ V E R S . ] ] [ _ _ _ _ _ _ ] ] [ R o tate En c o der V E R S . ] ] [ _ _ _ _ _ _ ] EN T ER VER S. R V R S D C L - 0 0 0 1 0 4 User Manual V E R S . ] ] [ - - - - - - ] P res s enter on V E RS field to return the M ain M enu that s hows the data regarding the s oftware and the equipm ent m odel. S D C 2 0 0 R o tate En c o der P res s enter to ac c es s the M ain M enu. } [ M e n u : ] [ B A C K ] [ S Y S T EM ] [ C LO C K R o tate En c o der : A N L - 1 [ < -- 6 0 . 0 0 ] || || || || || || || || || || || || || A N L - 2 [ < - 6 0 . 0 0 ] || || || || || || || || || || || || || { M a i n ] Rev. 1.1 - 04/07/12 [ B A C K ] 11 / 54 SDC200/RDS 5.3 ELETTRONICA CLIPPER and AGC - ON/OFF { M a i n [ A U D I O } [ M e n u : ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o } [ M e n u [ C H A NG E ] [ AG C O N ] [ C L I EN T ER A .G .C . { A u d i o M e n u [ C H A NG E ] [ NO 12 / 54 B A C K B A C K AG C ] [ NO Rev. 1.1 - 04/07/12 ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R EN T ER C L IP } [ ] [ I N P U T ] R o tate En c o der P res s enter to c hange the C lipper or A G C s tatus from O N to O F F and vic evers a. ] [ I N P U T ] [ O U T P U T ] C L I ] [ S e t A G C ] [ CO D E R ] R o tate En c o der User Manual SDC200/RDS ELETTRONICA 5.4 CODER - Selection of preemphasis { M a i n [ A U D I O } [ M e n u : ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P rem ere enter to ac c es s the audio m enu. { A u d i o } [ M e n u [ C H A NG E ] [ A G C B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o tate En c o der P res s enter to edit the C O D E R param eters . { CO D E R M e n u } [ S t e r e o ] [ NO P R E ] EN T ER PR E. { CO D E R M e n u } P R E ] M e n u } [ S t e r e o ] [ P R E { CO D E R M e n u 5 0 ] } [ S t e r e o ] [ P R E 7 5 ] E NTE R M e n u [ S t e r e o ] [ P R E User Manual L e v ] 1 9 K : [ - 2 0 . 0 ] R o tate En c o der [ B A C K L e v [ B A C K L e v [ - 2 0 . 0 ] ] 1 9 K : [ B A C K L e v ] 1 9 K : [ - 2 0 . 0 ] R o tate En c o der R o tate En c o der ] 1 9 K : [ - 2 0 . 0 ] P res s enter to c onfirm the s elec ted preem phas is value. PR E75 { CO D E R B A C K P res s enter to c hange the preem phas is value. [ S t e r e o ] [ NO { CO D E R [ } 7 5 ] [ B A C K L e v ] 1 9 K : [ Rev. 1.1 - 04/07/12 - 2 0 . 0 ] 13 / 54 SDC200/RDS 5.5 ELETTRONICA CODER - Selection of mono/stereo { M a i n [ A U D I O } [ M e n u : ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o M e n u [ C H A NG E ] [ A G C } [ B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o tate En c o der P res s enter to edit the C O D E R param eters . { CO D E R M e n u } [ S t e r e o ] [ NO P R E ] EN T ER PR E. { CO D E R M e n u } P R E ] M e n u } L ] [ NO P R E ] M e n u } R ] [ NO P R E ] M e n u } R + L ] [ NO P R E ] [ M o n o { CO D E R [ M o n o { CO D E R [ M n E NTE R PR E75 { CO D E R [ M n 14 / 54 B A C K ] 1 9 K : [ - 2 0 . 0 ] R o tate En c o der P res s enter to c hange the M ono/S tereo param eter. [ S t e r e o ] [ NO { CO D E R [ L e v [ B A C K L e v [ B A C K L e v [ [ - 2 0 . 0 ] ] 1 9 K : [ B A C K L e v - 2 0 . 0 ] ] 1 9 K : [ B A C K L e v ] 1 9 K : [ - 2 0 . 0 ] R o tate En c o der R o tate En c o der R o tate En c o der ] 1 9 K : [ - 2 0 . 0 ] P res s enter to c onfirm . M e n u } R + L ] [ NO P R E ] Rev. 1.1 - 04/07/12 [ B A C K L e v ] 1 9 K : [ - 2 0 . 0 ] User Manual SDC200/RDS ELETTRONICA 5.6 CODER - Modification of pilot tone level { M a i n [ A U D I O } [ M e n u : ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o ta te En c o der P res s enter to ac c es s the audio m enu. { A u d i o M e n u [ C H A NG E ] [ A G C } [ B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o ta te En c o der P res s enter to edit the C O D E R param eters . { CO D E R M e n u } [ S t e r e o ] [ NO P R E ] [ B A C K L e v ] 1 9 K : [ P res s enter to c hange the pilot tone level { CO D E R M e n u } [ S t e r e o ] [ NO P R E ] { CO D E R M e n u } [ S t e r e o ] [ NO P R E ] [ [ ] 1 9 K : [ B A C K L e v User Manual M e n u } [ S t e r e o ] [ NO P R E ] - 1 9 . 0 ] ] 1 9 K : [ - 2 0 . 0 ] R o ta te En c o der R o ta te En c o der E NTE R P res s enter to c onfirm . { CO D E R R o ta te En c o der EN T ER B A C K L e v - 1 9 . 0 ] [ B A C K L e v ] 1 9 K : [ Rev. 1.1 - 04/07/12 - 2 0 . 0 ] 15 / 54 SDC200/RDS ELETTRONICA 5.7 AGC - Adjusment of parameters { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o M e n u [ C H A NG E ] [ A G C } [ B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o tate En c o der P res s enter to ac c es s the A G C m enu. { A G C } [ M e n u M a x G a i n : [ - B A C K 6 . 0 ] [ ] A t t a c h : [ 2 . 0 ] 2 . 0 ] R e l e a s e : [ 0 . 5 ] EN T ER ATT. P res s enter to c hange the attac h tim e. { A G C M e n u M a x G a i n : [ } [ - A t t a c h : [ 4 . 0 ] 2 . 0 ] R e l e a s e : [ 0 . 5 ] B A C K 6 . 0 ] [ ] { A G C M e n u } [ - A t t a c h : [ 4 . 0 ] 2 . 0 ] R e l e a s e : [ 0 . 5 ] B A C K 6 . 0 ] [ ] R ouotate tare En c o der EN T ER ATT. P res s enter to c onfirm the value of s elec ted param eter. M a x G a i n : [ R o tate En c o der R o tate En c o der R e p e a t th e p ro ce d u re to ch a n g e th e re m a in in g p a ra m e te rs { A G C } [ M e n u M a x G a i n : [ - B A C K 6 . 0 ] [ A t t a c h : [ 4 . 0 ] 2 . 0 ] R e l e a s e : [ 0 . 5 ] E NTE R { A u d i o M e n u [ C H A NG E ] [ A G C } [ B A C K O N ] [ C L I ] P res s enter to return the A udio M enu. ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] The first field to the right of MaxGain represents the maximum attenuation that the AGC system can operate and it can have only negative values. The second field to the right of MaxGain represents the maximum gain that the AGC system can operate and it can has only positive values. The values entered in “Attach and Release” are expressed in dB/Sec. 16 / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 5.8 CODER INPUT - Selection of Analogic / Digital { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o M e n u [ C H A NG E ] [ A G C } [ B A C K O N ] [ C L I ] [ I N P U T M e n u [ ] A u t o [ } [ I n { I n p u t M e n u [ ] B A C K ] A N L ] [ } [ I n { I n p u t M e n u [ D i g i t ] { I n p u t M e n u B A C K [ I n DG T ] [ I n DG T ] [ I n DG T ] [ I n DG T ] [ I n DG T ] ] A N L ] [ } [ I n A N L ] [ I n A N L ] [ } [ A n a l o g ] R o tate En c o der B A C K B A C K ] ] R o tate En c o der R o tate En c o der R o tate En c o der P res s enter to c onfirm the field m odific ation. EN T ER { I n p u t M e n u [ ] A u t o R o tate En c o der P res s enter to m odify the field. EN T ER A u t o ] EN T ER P res s enter to ac c es s the input m enu. { I n p u t ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R } [ [ I n B A C K A N L ] ] The SDC200/RDS equipment is equipped with analogical balanced R&L inputs and digital inputs both optical and coaxial, and you can select them form Input Menu. Selecting [Auto] in presence of signal, both analogical and digital inputs, will be activated the digital source; in absence of digital signal on input will be activated the R&L analogical inputs. So the device provides automatic switching of inputs with digital priority. NOTE: “absence of digital signal” means the lack of AES/EBU plot or means errors on the same, and not regards to a possible lack of audio information iwithin it. Selecting [ Digit ] wiil be permanently active only the digital input. Selecting [ Analog ] wiil be permanently active only the analogical input. User Manual Rev. 1.1 - 04/07/12 17 / 54 SDC200/RDS 5.9 ELETTRONICA ANALOGICAL INPUTS - Adjustment of levels { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o } [ M e n u [ C H A NG E ] [ A G C B A C K O N ] [ C L I ] [ I N P U T M e n u [ ] A u t o ] R o tate En c o der EN T ER P res s enter to ac c es s the input. { I n p u t ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R [ } [ I n B A C K ] A N L ] [ I n DG T ] R o tate En c o der P res s enter to ac c es s the al m enu analogic al input m enu. { A n a l o g L e v e l I n p u t E NTE R R { A n a l o g L e v e l I n p u t R { A n a l o g 18 / 54 I n p u t [ B A C K L e v e l ] L : [ - 0 3 . 5 0 ] } [ B A C K L e v e l L ] L : [ - 0 4 . 5 0 ] R : [ - 0 3 . 0 0 ] Rev. 1.1 - 04/07/12 [ B A C K L e v e l R o tate En c o der E NTE R P res s enter to c onfirm the level of s elec ted input. } R o tate En c o der E NTE R P res s enter to c hange the level of s elec ted input. R : [ - 0 3 . 0 0 ] E NTE R L e v e l } R : [ - 0 3 . 5 0 ] L ] L : [ - 0 4 . 5 0 ] User Manual SDC200/RDS ELETTRONICA 5.10 DIGITAL INPUTS - Adjustment of levels { M a i n [ A U D I O } [ M e n u : ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o } [ M e n u [ C H A NG E ] [ A G C B A C K O N ] [ C L I ] [ I N P U T O N ] [ S e t A G C ] [ CO D E R M e n u [ ] A u t o ] R o tate En c o der EN T ER P res s enter to ac c es s the input. { I n p u t ] [ O U T P U T ] [ } [ I n B A C K ] A N L ] [ I n DG T ] R o tate En c o der P res s enter to ac c es s the al m enu digital input m enu. { D i g i t a l L e v e l I n p u t R : [ E NTE R R { D i g i t a l L e v e l R : [ I n p u t - R { D i g i t a l User Manual R : [ I n p u t - [ B A C K L e v e l ] L : [ } [ B A C K L e v e l } [ B A C K L e v e l Rev. 1.1 - 04/07/12 R o tate En c o der L ] L : [ - 1 . 7 ] R o tate En c o der E NTE R P res s enter to c onfirm the level of s elec ted input. 3 . 0 ] 0 . 0 ] E NTE R P res s enter to c hange the level of s elec ted input. 3 . 0 ] E NTE R L e v e l } 0 . 0 ] L ] L : [ - 1 . 7 ] 19 / 54 SDC200/RDS 5.11 ELETTRONICA INPUT SELECTION AND RESCUE SYSTEM { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o } [ M e n u [ C H A NG E ] [ A G C B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o tate En c o der P res s enter to ac c es s the C hange-O ver m enu. { C h a n g e O v e r } [ C o d e r < = = > C o d e r ] EN T ER { C h a n g e B A C K ] [ S o u r . 1 ] [ S o u r . 2 ] O v e r } [ B A C K ] [ S o u r . 1 ] [ S o u r . 2 ] { C h a n g e [ O v e r } B A C K ] [ I . M P X < = = > I . M P X ] [ S o u r . 1 ] [ S o u r . 2 ] { C h a n g e [ O v e r } B A C K ] [ C o d e r < = = > I . M P X ] [ S o u r . 1 ] [ S o u r . 2 ] { C h a n g e [ O v e r } B A C K ] [ I . M P X < = = > C o d e r ] [ S o u r . 1 ] [ S o u r . 2 ] { C h a n g e O n l y { C h a n g e [ O u t p u t { C h a n g e [ O n l y { C h a n g e O v e r } [ R D S ] [ S o u r . 1 ] [ S o u r . 2 ] } [ ] [ S o u r . 1 ] [ S o u r . 2 ] O v e r M u t e d O v e r EN T ER B A C K B A C K B A C K ] } [ R D S ] [ S o u r . 1 ] [ S o u r . 2 ] O v e r } [ B A C K ] ] [ S o u r . 1 ] [ S o u r . 2 ] { C h a n g e [ O v e r } [ C o d e r < = = > I . M P X ] EN T ER O v e r } [ C o d e r < = = > I . M P X ] Rev. 1.1 - 04/07/12 B A C K R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der ] [ I . M P X < = = > C o d e r ] { C h a n g e R o tate En c o der P res s enter to m odify the s ourc e s elec tion and to c onfirm the c hoic e. [ C o d e r < = = > C o d e r ] [ 20 / 54 [ R o tate En c o der R o tate En c o der ] [ S o u r . 1 ] [ S o u r . 2 ] P res s enter to c onfirm the s elec ted value. [ B A C K ] [ S o u r . 1 ] [ S o u r . 2 ] User Manual SDC200/RDS ELETTRONICA The SDC200/RDS is able to manage two sources, user selected among several combinations, that will be analyzed and eventually switched. The primary source is always 1 and, for example, it may be the stereo coder; source 2 will be the secondary and it could be for example the MPX. In case R&L input signal of stereo coder falls below the level set for a time greater than one defined (see Rescue System - Adjust timing and levels) and if secondary source is valid, the SDC200/ RDS will commutate on MPX input. It will return on stereo coder once the primary source level will be restored and will be elapsed time set. In case both sources were not valid, there will be no commutation and the primary source stay on. When you turn on the SDC200/RDS the source 1 will be considered immediately valid. In the following the association of source input. [ Coder <==> I.mpx ] Source1 Source2 In case source 1 is equal to source 2, the rescue system will be deactivated and the specified source will be activated. Example: [ I.mpx < > I.mpx ] mpx input source is working and rescue system is not working. If [rds only] is selected, only the RDS signal will be present on output. If [output muted] is selected, no signal will be present on output. It is also possible manage the mixing of RDS signal in according to the validity of the source (see “Rescue system - RDS Activation / Deactivation”). User Manual Rev. 1.1 - 04/07/12 21 / 54 SDC200/RDS 5.12 ELETTRONICA RESCUE SYSTEM - Time and level adjustment { M a i n } [ M e n u : ] [ [ A U D I O R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o } [ M e n u [ C H A NG E ] [ A G C B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o tate En c o der P res s enter to ac c es s the C hange-O ver m enu. { C h a n g e O v e r [ } [ C o d e r < = = > C o d e r ] M e n u } [ B A C K ] L e v e l : [ - 1 0 . 0 0 ] EN T ER { S o u r c e 1 M e n u { S o u r c e 1 M e n u M e n u } [ B A C K ] R D S : [ } [ B A C K ] R D S : [ } [ B A C K ] R D S : [ R o tate En c o der O N } [ O N ] 1 0 ] B A C K ] R D S : [ O N T ( s e c ) : [ } [ ] 1 0 ] R o tate En c o der R o tate En c o der EN T ER ] 2 0 ] R o tate En c o der E NTE R 20 B A C K L e v e l : [ - 1 2 . 0 0 ] 22 / 54 ] 1 0 ] T ( s e c ) : [ P res s enter to c onfirm the s w itc hing tim e. M e n u NO T ( s e c ) : [ L e v e l : [ - 1 2 . 0 0 ] { S o u r c e 1 R o tate En c o der P res s enter to c onfirm the s ourc e level. P res s enter to c hange the s w itc hing tim e. M e n u ] 1 0 ] T ( s e c ) : [ L e v e l : [ - 1 2 . 0 0 ] { S o u r c e 1 NO P res s enter to c hange the s ourc e level. L e v e l : [ - 1 2 . 0 0 ] { S o u r c e 1 R D S : [ R o tate En c o der EN T ER SO U R 2 T ( s e c ) : [ L e v e l : [ - 1 2 . 0 0 ] EN T ER -12.00 ] EN T ER SO U R 1 P res s enter to ac c es s the S ourc e1 or S ourc e2 m enu. { S o u r c e 1 B A C K [ S o u r . 1 ] [ S o u r . 2 ] Rev. 1.1 - 04/07/12 ] R D S : [ T ( s e c ) : [ O N ] 2 0 ] User Manual SDC200/RDS ELETTRONICA The source level defines the value below which the source is considered invalid. The source, to be valid, must have a greater or equal level than that defined by this parameter. The time defines the validity or invalidity of the source. In case the source will remain below the level previously defined, for a time equal or greater to than set, will be considered invalid. In case the source will stay higher than the level previously defined, for a time equal or greater to than set, will be considered valid. The time to retain valid or invalid the source is the same. User Manual Rev. 1.1 - 04/07/12 23 / 54 SDC200/RDS 5.13 ELETTRONICA RESCUE SYSTEM - RDS Activation / Deactivation { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o } [ M e n u [ C H A NG E ] [ A G C B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o tate En c o der P res s enter to ac c es s the C hange-O ver m enu. { C h a n g e O v e r [ } [ C o d e r < = = > C o d e r ] M e n u } [ ] EN T ER SO U R 1 P res s enter to ac c es s the S ourc e1 o S ourc e2 m enu. { S o u r c e 1 B A C K [ S o u r . 1 ] [ S o u r . 2 ] B A C K ] L e v e l : [ - 1 0 . 0 0 ] R D S : [ M e n u M e n u } [ B A C K ] M e n u } [ B A C K ] R D S : [ R D S : [ T ( s e c ) : [ } [ B A C K ] L e v e l : [ - 1 0 . 0 0 ] R D S : [ T ( s e c ) : [ M e n u R o tate En c o der NO ] 1 0 ] O N ] 1 0 ] A U T O R o tate En c o der R o tate En c o der ] 1 0 ] E NTE R P res s enter to c onfirm R D S s tatus . { S o u r c e 1 ] 1 0 ] T ( s e c ) : [ L e v e l : [ - 1 0 . 0 0 ] { S o u r c e 1 NO EN T ER L e v e l : [ - 1 0 . 0 0 ] { S o u r c e 1 EN T ER SO U R 2 T ( s e c ) : [ P res s enter to c hange R D S s tatus . { S o u r c e 1 R o tate En c o der AUTO } [ B A C K L e v e l : [ - 1 0 . 0 0 ] ] R D S : [ T ( s e c ) : [ A U T O ] 1 0 ] It is possible to define if RDS signal the RDS signal has to be mixed at the source, and if the mixing is dependent on the validity of status. The possible status are: [ NO ] = RDS not mixed [ ON ] = RDS mixed [ AUTO ] = RDS mixed only if the source is valid; in case of switching, between valid source and invalid source, the carrier will be turned off after 10 seconds. 24 / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 5.14 ANALOGICAL OUTPUT - Adjustment of audio level { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the audio m enu. { A u d i o M e n u [ C H A NG E ] [ A G C } [ B A C K O N ] [ C L I ] [ I N P U T ] [ O U T P U T ] O N ] [ S e t A G C ] [ CO D E R ] R o tate En c o der P res s enter to ac c es s the ouput m enu. { O u t p u t M e n u [ } L e v e l : [ [ O u t p u t ] M e n u } [ L e v e l : [ [ O u t p u t ] M e n u } [ O u t p u t ] EN T ER User Manual B A C K ] 0 . 7 ] R o tate En c o der [ L e v e l : [ B A C K ] 0 . 7 ] R o tate En c o der P res s enter to ac tivate or deac tivate the ouputs { O u t p u t [ M u t e d R o tate En c o der EN T ER P res s enter to c onfirm the level of s elec ted ouput. { O u t p u t ] 0 . 0 ] EN T ER P res s enter to c hange the level of s elec ted ouput. { O u t p u t B A C K M e n u ] } [ L e v e l : [ B A C K ] 0 . 7 ] Rev. 1.1 - 04/07/12 25 / 54 SDC200/RDS 5.15 ELETTRONICA RDS – Carrier Activation / Deactivation { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ D S N } [ M e n u 1 ] [ P S N B A C K ] [ C a r r i . ] [ C L O C K L e v e l : [ R D S [ } 0 . 0 6 9 ] B A C K ] R D S : [ < V o l t > L e v e l : [ R D S [ } 0 . 0 6 9 ] < V o l t > P res s enter to return the R D S M enu. { R DS [ D S N M e n u 1 ] [ P S N } [ B A C K B A C K O F F ] R o tate En c o der EN T ER P res s enter to c heange the s tatus of R D S c arrier from on to off and vic evers a. { H a r d w a r e R o tate En c o der EN T ER P res s enter to ac c es s the R D S H ardw are m enu. { H a r d w a r e ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] ] R D S : [ O N ] R o tate En c o der EN T ER ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] The deactivation of RDS carrier from this menu will make it impossible to switch on of the same from change menu (sour.1 and sour.2). To activate the RDS carrier management menu from change menu is essential that the carrier is activated. 26 / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 5.16 RDS – Adjustment of carrier level { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the the R D S m enu. { R DS [ D S N } [ M e n u 1 ] [ P S N B A C K ] [ C a r r i . ] [ C L O C K L e v e l : [ R D S L e v e l : [ R D S { H a r d w a r e L e v e l : [ User Manual R D S B A C K ] R D S : [ [ } 0 . 0 6 9 ] EN T ER < V o l t > O F F ] O F F ] O F F ] R o tate En c o der P res s E nter to c hange the c arrier level s eparately for eac h output. EN T ER { H a r d w a r e [ } 0 . 0 5 0 ] R o tate En c o der EN T ER P res s enter to ac c es s the R D S H ardw are m enu. { H a r d w a r e ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] < V o l t > B A C K ] R D S : [ R o tate En c o der P res s enter to c onfirm the output level s elec ted. [ } 0 . 0 6 9 ] < V o l t > B A C K ] R D S : [ Rev. 1.1 - 04/07/12 27 / 54 SDC200/RDS ELETTRONICA 5.17 RDS – Adjustment of clock time { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o ta te En c o der P res s enter to ac c es s the R D S m enu. { R DS [ } [ M e n u D S N 1 ] [ P S N B A C K ] [ C a r r i . ] [ C L O C K P res s enter to ac c es s the C loc k M enu D uring the m odify to hour or date, the c loc k w ill be freez e. { C l o c k M e n u 1 1 : 4 1 : 0 9 ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] } [ B A C K 0 8 - 0 9 - 2 0 0 9 R o ta te En c o der E NTE R ] R o ta te En c o der [ + 0 0 . 0 ] H our s elec tion. { C l o c k M e n u 1 1 : 4 1 : 0 9 } [ B A C K 0 8 - 0 9 - 2 0 0 9 ] R o ta te En c o der [ + 0 0 . 0 ] M inute s elec tion. { C l o c k M e n u 1 1 : 4 1 : 0 9 } [ B A C K 0 8 - 0 9 - 2 0 0 9 ] R o ta te En c o der [ + 0 0 . 0 ] S ec onds s elec tion. { C l o c k M e n u 1 1 : 4 1 : 0 9 } [ B A C K 0 8 - 0 9 - 2 0 0 9 ] R o ta te En c o der [ + 0 0 . 0 ] D ay s elec tion. { C l o c k M e n u 1 1 : 4 1 : 0 9 } [ B A C K 0 8 - 0 9 - 2 0 0 9 ] R o ta te En c o der [ + 0 0 . 0 ] M onth s elec tion. { C l o c k M e n u 1 1 : 4 1 : 0 9 } [ B A C K 0 8 - 0 9 - 2 0 0 9 ] R uo tare En c o der [ + 0 0 . 0 ] Y ear s elec tion. { C l o c k M e n u 1 1 : 4 1 : 0 9 } [ B A C K 0 8 - 0 9 - 2 0 0 9 ] R uo tare En c o der [ + 0 1 . 0 ] S elec tion of G reenw ic h M ean Tim e G M T O ffs et EN T ER P res s enter to c onfirm the s elec ted param eter. { C l o c k M e n u 1 1 : 4 1 : 0 9 } [ 0 8 - 0 9 - 2 0 0 9 [ 28 / 54 D S N M e n u 1 ] [ P S N ] R uo tare En c o der [ + 0 1 . 0 ] EN T ER P res s enter to return the R D S m enu. { R DS B A C K } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] Rev. 1.1 - 04/07/12 R uo tare En c o der User Manual SDC200/RDS ELETTRONICA Italy ,being a country with a single time zone, can have time offset equal to 00.0. User Manual Rev. 1.1 - 04/07/12 29 / 54 SDC200/RDS ELETTRONICA 5.18 RDS – Selection of DSN { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ 1 ] [ P S N EN T ER { R DS [ [ { R DS [ M e n u 3 ] [ P S N M e n u 4 ] [ P S N M e n u D S N { R DS [ 2 ] [ P S N D S N { R DS [ M e n u D S N { R DS [ 1 ] [ P S N D S N 5 ] [ P S N M e n u D S N 6 ] [ P S N EN T ER { R DS [ 30 / 54 D S N B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] R o tate En c o der P res s enter to s elec t the D S N to c hange M e n u D S N { R DS } [ M e n u D S N } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] Ro uotate tar e En c o der Ro uotate tar e En c o der Ro uotate tar e En c o der Ro uotate tar e En c o der Ro uotate tar e En c o der Ro uotate tar e En c o der P res s enter to c onfirm the s elec ted param eter. M e n u 6 ] [ P S N } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] Rev. 1.1 - 04/07/12 Ro uotate tar e En c o der User Manual SDC200/RDS ELETTRONICA 5.19 RDS – Selection of PSN { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ D S N } [ M e n u 1 ] [ P S N EN T ER { R DS [ D S N { R DS [ D S N { R DS [ D S N } [ } [ B A C K ] [ C a r r i . ] [ C L O C K ] B A C K ] [ C a r r i . ] [ C L O C K ] 1 ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] 2 ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] } [ M e n u 1 ] [ E O N ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] M e n u 1 ] [ E O N ] [ C a r r i . ] [ C L O C K R o tate En c o der P res s enter to s elec t the P S N to c hange There are a M ain P S N and 7 E O N for eac h D S N M e n u 1 ] [ P S N B A C K M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] B A C K ] [ C a r r i . ] [ C L O C K ] R ouotate tare En c o der R ouotate tare En c o der R ouotate tare En c o der R e p e a t th e p ro ce d u re b y tu rn in g th e e n co d e r to se le ct th e d e sire d EO N { R DS [ D S N } [ M e n u 1 ] [ E O N 7 EN T ER { R DS [ User Manual D S N ] [ C a r r i . ] [ C L O C K ] R ouotate tare En c o der P res s enter to c onfirm the s elec ted param eter. } [ M e n u 1 ] [ E O N B A C K ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] 7 B A C K ] [ C a r r i . ] [ C L O C K ] ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] Rev. 1.1 - 04/07/12 R ouotate tare En c o der 31 / 54 SDC200/RDS 5.20 ELETTRONICA RDS - Entering or editing of the PS in Main PSN { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ } [ M e n u D S N 1 ] [ P S N B A C K ] [ C a r r i . ] [ C L O C K M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] B A C K ] P S " [ D I : [ B A C K ] " M o , N r , P res s E nter w hen flas hing the firs t c harac ter to update the field. , s ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R ouotate tare En c o der EN T ER P S " _ [ D I : R o tate En c o der EN T ER P res s E nter only after y ou s elec t the D S N and the P S N by w hic h m odify P S . [ ] M o , N r , " , s ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der EN T ER [ B A C K ] P S " N _ [ D I : M o , N r , " , s ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der EN T ER [ B A C K ] P S " NO _ [ D I : M o , N r , " , s ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der EN T ER [ B A C K ] P S " NOM _ [ D I : M o , N r , " , s ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der EN T ER [ B A C K ] P S " NOM E _ [ D I : 32 / 54 M o , N r , Rev. 1.1 - 04/07/12 , s " ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der User Manual SDC200/RDS ELETTRONICA [ B A C K ] P S " NOM E _ [ D I : M o , N r , " , s ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der EN T ER [ B A C K ] P S " NOM E [ D I : M o , N r , _ , s " ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der EN T ER [ B A C K ] P S " NOM E [ D I : M o , N r , , s _ " P I [ 5 0 0 0 ] ] [ S e e t P T Y ] R o tate En c o der EN T ER [ B A C K ] P S " NOM E [ D I : EN T ER { R DS [ User Manual D S N M o , N r , " , s ] P I [ 5 0 0 0 ] [ S e e t P T Y ] R o tate En c o der P res s enter to return the R D S m enu. M e n u 1 ] [ P S N } [ B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] Rev. 1.1 - 04/07/12 33 / 54 SDC200/RDS 5.21 ELETTRONICA RDS - Entering or editing of the DI in Main PSN { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter tp ac c es s the R D S m enu. { R DS [ M e n u D S N 1 ] [ P S N } [ B A C K ] [ C a r r i . ] [ C L O C K M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] B A C K ] P S " R A D I O [ D I : P res s E nter to c hange D I by turning enc oder y ou get all 16 pos s ible c om binations . [ B A C K ] [ B A C K ] B A C K ] B A C K ] B A C K ] [ B A C K ] P res s E nter to c onfirm M o/S t = > M ono or S tereo N r/A r = > N orm ale or artific iale C = > C om pres s ed A udio s /d = > S tatic or dy nam ic P TY B A C K ] [ S e t P T Y ] " ] S t , N r , , s S t , A r , , s S t , A r , C , s S t , A r , C , d S t , A r , C , d P I [ 5 0 0 0 ] [ S e t P T Y ] " ] P I [ 5 0 0 0 ] [ S e t P T Y ] " ] P I [ 5 0 0 0 ] [ S e t P T Y ] " ] P I [ 5 0 0 0 ] [ S e t P T Y ] " ] P I [ 5 0 0 0 ] [ S e t P T Y ] " ] R ouotate tare En c o der P I [ 5 0 0 0 ] [ S e t P T Y ] R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R uo tare En c o der EN T ER P S " R A D I O [ D I : 34 / 54 , s P S " R A D I O [ D I : [ M o , N r , P S " R A D I O [ D I : P I [ 5 0 0 0 ] EN T ER P S " R A D I O [ D I : [ " ] P S " R A D I O [ D I : [ , s P S " R A D I O [ D I : [ M o , N r , P S " R A D I O [ D I : R o tate En c o der EN T ER P res s E nter only after y ou s elec t the D S N and the P S N by w hic h m odify D I. [ ] S t , A r , C , d Rev. 1.1 - 04/07/12 " ] P I [ 5 0 0 0 ] [ S e t P T Y ] R uo tare En c o der User Manual SDC200/RDS ELETTRONICA 5.22 RDS - Entering or editing of the PI in Main PSN { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ } [ M e n u D S N 1 ] [ P S N B A C K ] [ C a r r i . ] [ C L O C K M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] B A C K ] P S " R A D I O [ D I : M o , N r , , s " ] B A C K ] [ L o c a l B A C K ] [ L o c a l [ B A C K P I He x : 5 0 0 0 P I He x : 5 0 0 0 ] B A C K User Manual ] ] R ouotate tare En c o der P I He x : 5 0 3 4 P I He x : 5 0 3 4 ] [ I , J O R , S L O Rev. 1.1 - 04/07/12 R o tate En c o der EN T ER N u m : [ 0 0 0 ] ] N u m : [ 0 5 2 ] ] [ I , J O R , S L O P res s E nter to c onfirm the s elec ted param eter. [ L o c a l N u m : [ 0 0 0 ] ] [ I , J O R , S L O [ L o c a l [ [ S e t P T Y ] ] [ I , J O R , S L O P re ss En te r to m o d ify th e sta tio n id e n tifica tio n n u m b e r [ P I [ 5 0 0 0 ] EN T ER P res s E nter to ac c es s the P I m enu. [ R o tate En c o der EN T ER P res s E nter only after y ou s elec t D S N and the P S N by w hic h m odify P I [ ] ] R o tate En c o der R o tate En c o der EN T ER N u m : [ 0 5 2 ] ] R o tate En c o der 35 / 54 SDC200/RDS [ ELETTRONICA B A C K ] P I He x : 5 0 3 4 [ L o c a l B A C K P I He x : 5 0 3 4 ] [ L o c a l [ B A C K P I He x : 5 1 3 4 ] B A C K B A C K P I He x : 5 3 3 4 ] r e g i o n . [ ] [ R e g i o n EN T ER [ B A C K 36 / 54 R o tate En c o der N u m : [ 0 5 2 ] ] N u m : [ 0 5 2 ] ] N u m : [ 0 5 2 ] ] [ I , J O R , S L O ] R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der P res s E nter to c onfirm the s elec ted param eter. ] [ R e g i o n ] ] [ I , J O R , S L O P I He x : 5 4 3 4 1 N u m : [ 0 5 2 ] ] [ I , J O R , S L O [ E x t r a B A C K ] ] [ I , J O R , S L O P I He x : 5 2 3 4 ] [ N a t i o n a l [ N u m : [ 0 5 2 ] ] [ I , J O R , S L O [ I n t e r n a t i o n a l [ ] P re ss En te r to in se rt o r to m o d ify th e co ve ra g e a re a . EN T ER [ N u m : [ 0 5 2 ] ] [ I , J O R , S L O P I He x : 5 4 3 4 1 ] [ I , J O R , S L O Rev. 1.1 - 04/07/12 N u m : [ 0 5 2 ] ] R o tate En c o der User Manual SDC200/RDS ELETTRONICA [ B A C K ] [ R e g i o n P I He x : 5 4 3 4 1 B A C K [ B A C K B A C K [ B A C K B A C K 1 ] [ B E L , F N L , S Y R , Y UG P I He x : 6 4 3 4 P I He x : 7 4 3 4 ] [ A L G , C Y P , T C H , I R L 1 ] [ I , J O R , S L O P I He x : 2 4 3 4 P I He x : 5 4 3 4 B A C K [ R e g i o n User Manual ] R o tate En c o der ] N u m : [ 0 5 2 ] ] N u m : [ 0 5 2 ] ] R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der EN T ER P I He x : 5 4 3 4 1 ] N u m : [ 0 5 2 ] 1 P res s E nter to c onfirm the s elec ted param eter. [ N u m : [ 0 5 2 ] ] [ B L R , L U X , U K R , T U N , U S S R ] [ R e g i o n ] 1 ] [ R e g i o n [ ] [ I , J O R , S L O ] [ R e g i o n N u m : [ 0 5 2 ] 1 ] [ R e g i o n [ P I He x : 5 4 3 4 ] [ R e g i o n ] EN T ER P re ss En te r to ch a n g e th e n a tio n o f sta tio n b e tw e e n 16 ch o ice . [ N u m : [ 0 5 2 ] ] [ I , J O R , S L O ] [ I , J O R , S L O Rev. 1.1 - 04/07/12 N u m : [ 0 5 2 ] ] R o tate En c o der 37 / 54 SDC200/RDS 5.23 ELETTRONICA RDS - Entering or editing of the TA, TP and MS in Main PSN { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T EM ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ M e n u D S N 1 ] [ P S N } [ B A C K ] [ C a r r i . ] [ C L O C K B A C K ] P S " R A D I O [ D I : M o , N r , , s " P I [ 5 4 3 4 ] [ S e t P T Y ] ] B A C K ] P T Y N " [ T A B A C K ] P T Y N " 38 / 54 O F F ] [ T P " P res s enter to c hange the of TA , TP and M S s tatus from on to off and vic evers a [ R ouotate tare En c o der EN T ER P res s E nter to ac c es s the P TY m enu. [ R o tate En c o der EN T ER P res s E nter only after y ou s elec t D S N and theP S N by w hic h m odify P TY [ ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] O F F ] [ M S [ P T Y : EN T ER [ T A " Rev. 1.1 - 04/07/12 O N A L A RM ! O N [ P T Y : R ouotate tare En c o der MS TP ] [ T P ] EN T ER EN T ER TA O F F ] ] [ M S A L A RM ! O N ] ] User Manual SDC200/RDS ELETTRONICA 5.24 RDS - Entering or editing PTYN in Main PSN { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ } [ M e n u D S N 1 ] [ P S N B A C K ] [ C a r r i . ] [ C L O C K M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] P res s E nter only after y ou s elec t D S N and P S N of P S to m odify . [ B A C K ] P S " R A D I O M o , N r , , s " P I [ 5 4 3 4 ] [ S e t P T Y ] ] P res s E nter to ac c es s the P TY m enu. B A C K ] [ T A ] B A C K [ B A C K B A C K ] ] ] O N ] [ T P O N ] [ T P O N [ P T Y : [ T A P T Y N " C A L C I O O N " _ " A L A RM ! ] R ouotate tare En c o der O N ] [ T P O N [ P T Y : ] [ M S O N A L A RM ! ] [ M S ] O N A L A RM ! ] [ M S ] [ M S ] ] O N A L A RM ! A L A RM ! ] ] ] O N ] ] R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der The m odify ends w ith E N TE R on the las t c harac ter of s tring and by enc oder rotation y ou c an c hoos e other fields . EN T ER B A C K ] [ T P [ P T Y : [ T A P T Y N " C A L C I O [ O N " P T Y N " C A _ [ O N [ P T Y : [ T A P T Y N " C _ O F F ] P res s enter on firs t c harac ter that flas hing in c as e y ou w ant to m odify the s tring " ] O F F ] [ M S [ P T Y : [ T A P T Y N " _ [ O F F ] [ T P " EN T ER B A C K R ouotate tare En c o der EN T ER P T Y N " _ [ R o tate En c o der EN T ER [ D I : [ ] [ T A " O F F ] [ T P O F F ] [ M S [ P T Y : A L A RM ! O F F ] ] R ouotate tare En c o der R o ta te e n co d e r to p ro ce e d w ith e n te rin g o f b ro a d ca st p ro g ra m typ e User Manual Rev. 1.1 - 04/07/12 39 / 54 SDC200/RDS [ ELETTRONICA B A C K ] P T Y N " C A L C I O [ T A O N ] [ T P O N [ P T Y : " B A C K ] P T Y N " C A L C I O [ B A C K ] P T Y N " C A L C I O [ B A C K ] P T Y N " C A L C I O [ B A C K ] P T Y N " C A L C I O [ B A C K ] P T Y N " C A L C I O [ T A O N O N O N O N O N ] [ T P O N ] [ T P O N [ P T Y : " [ T A ] [ T P [ P T Y : " [ T A O N [ P T Y : " [ T A ] [ T P [ P T Y : " [ T A O N ] [ T P O N [ P T Y : " B A C K ] P T Y N " C A L C I O 40 / 54 [ T A " Rev. 1.1 - 04/07/12 ] ] R ouotate tare En c o der O N ] [ M S O N A L A RM ! ] [ M S ] O N N EW S ] [ M S ] ] ] O N ] B U S I N N E S ] ] [ M S O N ] I N F O RM A T . ] ] [ M S O N S P O R T ] ] R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der EN T ER P res s E nter to c onfirm the s elec ted param eter. [ O N EN T ER P res s E nter to c hange the program ty pe. [ ] [ M S A L A RM ! ] [ T P O N [ P T Y : ] [ M S S P O R T O N ] ] R ouotate tare En c o der User Manual SDC200/RDS ELETTRONICA 5.25 RDS - Insertion of Alternative Frequencies { M a i n } [ M e n u : ] [ [ A U D I O R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ D S N } [ M e n u 1 ] [ P S N R D S ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] M e n u [ } [ A . F r e q ] EN T ER [ Q / S / C ] A F [ 0 0 ] [ - - - , - ] [ - - - , - ] R o tate En c o der EN T ER P res s E nter only after y ou s elec t the D S N from the lis t to m odify { D S N B A C K B A C K ] R ouotate tare En c o der [ R . T e x t ] P res s E nter to ac c es s the F requenc y Lis t m enu. W hen y ou enter, a c opy of the vis ualiz ed lis t is m ade. This is to avoid interruptions or errors in trans m is s ion. E ac h D S N c an have until to 100 lis t and until 1000 frequenc ies . B [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] R ouotate tare En c o der This field allow s y ou to s elec t the lis t y ou w ant to view or to c hange only am ong thos e pres ent and one blank . [ Q / S / C ] A F [ 0 0 ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] R ouotate tare En c o der This field (H ead Lis t)is filled only on Ty pe-B lis t [ Q / S / C ] A F [ 0 0 ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] P res s E nter to editing the frequenc y lis t field. The head lis t frequenc y is c anc eled under 87.6 The frequenc ies are c anc eled over 107,9 User Manual [ Q / S / C ] A F [ 0 0 ] [ - - - , - ] [ - - - , - ] R ouotate tare En c o der EN T ER B [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] Rev. 1.1 - 04/07/12 R ouotate tare En c o der 41 / 54 SDC200/RDS ELETTRONICA [ Q / S / C ] A F [ 0 0 ] [ - - - , - ] [ - - - , - ] [ Q / S / C ] A F [ 0 0 ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ 1 0 1 , 5 ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] R ouotate tare En c o der R uo tare En c o der EN T ER P res s E N TE R at the end of m odific ation. T h e ch a n g e s ta ke e ffe ct o n ly w h e n yo u sa ve b e fo re e x it. [ Q / S / C ] A F [ 0 0 ] [ - - - , - ] [ - - - , - ] [ Q / S / C ] A F [ 0 0 ] [ 0 9 7 , 0 ] [ - - - , - ] B [ - - - , - ] [ 1 0 1 , 5 ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ 1 0 1 , 5 ] [ - - - , - ] [ 0 8 8 , 2 ] [ 1 0 0 , 0 ] [ - - - , - ] R ouotate tare En c o der R ouotate tare En c o der Y ou c an edit the lis ts in the order that y ou prefer als o w ith blank fields . The ty pe-A lis t c an have 25 frequenc ies , w hile thos e ty pe-B lis t c an have only 12 over the head lis t. [ Q / S / C ] A F [ 0 0 ] [ 0 9 7 , 0 ] [ - - - , - ] EN T ER [ Q / S / C ] A F [ 0 0 ] [ 1 0 0 , 0 ] [ 1 0 1 , 5 ] [ Q / S / C ] A F [ 0 1 ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ 1 0 1 , 5 ] [ - - - , - ] [ 0 8 8 , 2 ] [ 1 0 0 , 0 ] [ - - - , - ] R ouotate tare En c o der U s ing E N TE R y ou c hange the lis t, but the firs t m ovem ent of the enc oder A R R A N G ES the lis t as follow s . B [ - - - , - ] [ 0 8 8 , 2 ] [ 0 9 7 , 0 ] [ - - - , - ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] B [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] [ - - - , - ] R ouotate tare En c o der R ouotate tare En c o der EN T ER [ Q / S / C ] A F [ 0 1 ] [ - - - , - ] [ - - - , - ] R ouotate tare En c o der Q = > n e e d to e x it th e m e n u w ith o u t sa vin g a n y ch a n g e s to th e lists S = > n e e d to e x it th e m e n u sa vin g th e ch a n g e s m a d e to th e lists. C = > n e e d to e ra se a ll fie ld s in th e list d isp la ye d . 42 / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 5.26 RDS - Radio Text entry { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ } [ M e n u D S N 1 ] [ P S N R D S M e n u ] [ C a r r i . ] [ C L O C K [ } R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l B A C K ] R ouotate tare En c o der [ R . T e x t ] EN T ER P res s E nter to ac c es s the radio-tex t m enu. [ Q / S ] R o tate En c o der EN T ER [ A . F r e q ] a d c a s t ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] P res s E nter only after y ou s elec t the D S N of radio-tex t to m odify . { D S N B A C K - M o n o + R D S - B r o R ouotate tare En c o der - B r o R ouotate tare En c o der - B r o R ouotate tare En c o der - B r o R ouotate tare En c o der P r o c e s s o r Q = > need to ex it the radio-tex t m enu w ithout s aving any c hanges to the m enu. [ Q / S ] a d c a s t R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l - M o n o + R D S P r o c e s s o r S = > need to ex it the radio-tex t m enu s aving the c hanges m ade to the m enu. [ Q / S ] a d c a s t R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l - M o n o + R D S P r o c e s s o r This field allow s y ou to s elec t the radio-tex t y ou w ant to view or to c hange only am ong thos e pres ent and one blank . [ Q / S ] a d c a s t R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l - M o n o + R D S P r o c e s s o r This field allow s y ou to s elec t the radio-tex t ty pe A = > the rec eiver updates the dis play w ithout deleting the previous m es s age. B = > the rec eiver updates the dis play after delating the previous m es s age. User Manual Rev. 1.1 - 04/07/12 43 / 54 SDC200/RDS [ Q / S ] a d c a s t ELETTRONICA R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l - M o n o + R D S - B r o R ouotate tare En c o der B r o R ouotate tare En c o der P r o c e s s o r This field allow s y ou to s elec t the repetitions num ber of radio-tex t, before m oving to nex t. " 0" m eans infinite. [ Q / S ] a d c a s t R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l - M o n o + R D S - P r o c e s s o r This field, lik e the follow ing 63, are all c harac ters of the m es s age that c an be edited individually . Y ou get a s pec ial c harac ter that repres ents the end of the radio-tex t , by turning the k nob to the left from the s pac e. [ Q / S ] a d c a s t R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l - M o n o This term inator c harac ter is us eful if y ou w ant to s horten the m es s age. [ Q / S ] a d c a s t [ Q / S ] a d c a s t R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l R T 0 0 D i g i t a l B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l a d c a s t R T 0 0 B [ 0 0 ] P 7 0 0 3 S i g n a l a d c a s t R T 0 0 - B r o R ouotate tare En c o der - M o n o + R D S - B r o R ouotate tare En c o der R D S - B r o R ouotate tare En c o der - B r o R ouotate tare En c o der B r o R ouotate tare En c o der P r o c e s s o r - M o n o _ _ P r o c e s s o r - D o u b le EN T ER M o n o _ _ R D S P r o c e s s o r To tes t the effec t of the term inator go nex t m es s age in w ay that the edited m es s age is edited. EN T ER [ Q / S ] D i g i t a l R D S EN T ER The double E N TE R is us ed to ex it from editing before reac hing the 64° c harac ter of the s tring. [ Q / S ] + P r o c e s s o r B [ 0 0 ] P 7 0 0 3 S i g n a l D i g i t a l - M o n o _ _ R D S - P r o c e s s o r [ Q / S ] R T 0 1 A [ 0 0 ] [ Q / S ] R T 0 0 B [ 0 0 ] P 7 0 0 3 - M o n o R ouotate tare En c o der [ Q / S ] R T 0 0 B [ 0 0 ] P 7 0 0 3 - M o n o R ouotate tare En c o der B [ 0 0 ] P 7 0 0 3 - M o n o R ouotate tare En c o der R ouotate tare En c o der EN T ER [ Q / S ] R T 0 0 Q = > n e e d to e x it th e te x t-ra d io m e n u w ith o u t sa vin g a n y ch a n g e s to th e m e n u . S = > n e e d to e x it th e te x t-ra d io m e n u sa vin g th e ch a n g e s m a d e to th e m e n u . 44 / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 5.27 RDS - Block Custom Messages entry { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T EM ] [ C LO C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the RDS m enu. { R DS [ D S N } [ M e n u 1 ] [ P S N B A C K ] [ C a r r i . ] [ C LO C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ Me s s a g ] R o tate En c o der EN T ER [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der Q = > need to ex it the m enu without s aving any c hanges to the m es s age. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der S = > need to ex it the m enu s aving the c hanges m ade to the m es s age. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der This field is us ed to s elec t the m es s age that y ou w ant to s ee and / or to c hange. Ea ch m e ssa g e is in d e p e n d e n t fro m th e o th e rs, ch a n g in g m e ssa g e yo u w ill lo se a n y u n sa ve d ch a n g e s. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " This field is us ed to c hoos e the ty pe of m es s age. - = > The m es s age is not enabled for trans m is s ion. B = > The m es s age is enabled for bloc k trans m is s ion. < = > The m es s age is enabled for trans m is s ion w ith left s c roll. > = > The m es s age is enabled for trans m is s ion w ith right s c roll. # = > The m es s age is enabled for trans m is s ion w ith alternating s c roll. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] [ Q / S ] M s g [ 0 1 ] EN T ER T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] T y p e [ B ] B l k [ 0 0 ] " " " T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " R ouotate tare En c o der " R ouotate tare En c o der R ouotate tare En c o der EN T ER [ Q / S ] M s g [ 0 1 ] T y p e [ B ] B l k [ 0 0 ] [ Q / S ] M s g [ 0 1 ] R i p [ 0 0 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] " " T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der R ouotate tare En c o der This field is us ed to s elec t the s tart tim e of m es s age trans m is s ion. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der This field is us ed to s elec t the s tart m inute of m es s age trans m is s ion. User Manual Rev. 1.1 - 04/07/12 45 / 54 SDC200/RDS [ Q / S ] ELETTRONICA M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " This field repres ents the num ber of repetitions before m oving on to the nex t bloc k . W A R N IN G , values low er than 3 m ay not guarantee the dis play on s om e rec eivers . This field to z ero ex c ludes the trans m is s ion bloc k . [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] " " P res s E N TE R to enter and ex it the c hange of repetitions num ber. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] " - " This field is c om pos ed of 8 editable c harac ters . A term inator eras es the c harac ters after the c urrent bloc k . [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] " B L O C CO 1 " A fter the editing of the c harac ter, pres s again E N TE R . [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] R ouotate tare En c o der R ouotate tare En c o der EN T ER R ouotate tare En c o der EN T ER T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] EN T ER EN T ER T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] R ouotate tare En c o der " B L O C CO 1 " R ouotate tare En c o der A fter the editing of the c harac ter, pres s again E N TE R . [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 1 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der A fter the editing of the c harac ter, pres s again E N TE R . C ontinuing to turn the enc oder after the eighth c harac ter of bloc k 0 y ou pas s to the repetitions of bloc k 1 and s o on until the s ix teenth bloc k . 46 / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 5.28 RDS - Scrolling Custom Messages entry { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the R D S m enu. { R DS [ D S N } [ M e n u 1 ] [ P S N B A C K ] [ C a r r i . ] [ C L O C K ] M . ] [ S e t D s n ] [ S e t P s n ] [ M e s s a g ] R o tate En c o der EN T ER [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der Q = > need to ex it the m enu w ithout s aving any c hanges to the m es s age. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der S = > need to ex it the m enu s aving the c hanges m ade to the m es s age. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " " R ouotate tare En c o der This field is us ed to s elec t the m es s age that y ou w ant to s ee and / or to c hange. Ea ch m e ssa g e is in d ip e n d e n t fro m th e o th e rs, ch a n g in g m e ssa g e yo u w ill lo se a n y u n sa ve d ch a n g e s. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] " This field is us ed to c hoos e the ty pe of m es s age. - = > The m es s age is not enabled for trans m is s ion. B = > The m es s age is enabled for bloc k trans m is s ion. < = > The m es s age is enabled for trans m is s ion w ith left s c roll. > = > The m es s age is enabled for trans m is s ion w ith right s c roll. # = > The m es s age is enabled for trans m is s ion w ith alternating s c roll. [ Q / S ] M s g [ 0 1 ] T y p e [ - ] B l k [ 0 0 ] [ Q / S ] User Manual M s g [ 0 1 ] " " T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] Rev. 1.1 - 04/07/12 R ouotate tare En c o der EN T ER T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] T y p e [ < ] " R ouotate tare En c o der R ouotate tare En c o der 47 / 54 SDC200/RDS [ Q / S ] ELETTRONICA M s g [ 0 1 ] T y p e [ < ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] R ouotate tare En c o der EN T ER [ Q / S ] M s g [ 0 1 ] T y p e [ < ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] R ouotate tare En c o der [ Q / S ] M s g [ 0 1 ] T y p e [ < ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] R ouotate tare En c o der This field is us ed to s elec t the s tart tim e of m es s age trans m is s ion. [ Q / S ] M s g [ 0 1 ] T y p e [ < ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] R ouotate tare En c o der This field is us ed to s elec t the s tart m inute of m es s age trans m is s ion. [ Q / S ] M s g [ 0 1 ] T y p e [ < ] T i m e [ 0 0 : 0 0 ] R i p [ 0 0 ] This field repres ents the num ber of repetitions before m oving on to the nex t bloc k W A R N IN G , values low er than 3 m ay not guarantee the dis play on s om e rec eivers . This field to 0 is equal to 1 [ Q / S ] M s g [ 0 1 ] T y p e [ < ] EN T ER T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] P res s E N TE R to enter and ex it the c hange of repetitions num ber. [ Q / S ] M s g [ 0 1 ] T y p e [ < ] T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] E s e m p i o d i T y p e [ < ] M e s s a g g i o T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] s c o r r e v o l e [ Q / S ] M s g [ 0 1 ] 48 / 54 d i T y p e [ < ] M e s s a g g i o Rev. 1.1 - 04/07/12 T i m e [ 0 0 : 0 0 ] R i p [ 0 5 ] s c o r r e v o l e R ouotate tare En c o der EN T ER A fter the editing of the c harac ter, pres s again E N TE R . E s e m p i o R ouotate tare En c o der EN T ER Turning the enc oder, after the repetitions , y ou pas s to the firs t of 128 c harac ters from w hic h c an be m ade the the s c rolling m es s age. M s ??g [ 0 1 ] R ouotate tare En c o der EN T ER _ [ Q / S ] R ouotate tare En c o der R ouotate tare En c o der User Manual SDC200/RDS ELETTRONICA 5.29 RS232 - COM1, COM2 and COM3 Serial Configuration { M a i n [ A U D I O } [ M e n u : ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the s y s tem m enu. [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] P res s enter to c hange the param eters of C om 1 or C om 2 or C om 3 s erials . [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] [ B A C K ] [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] [ B A C K ] [ B A C K ] [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] [ B A C K ] [ B A C K ] P res s enter to c onfirm the s elec ted value. B A C K ] 3 8 4 0 0 ] { - - - } 5 7 6 0 0 ] [ 5 7 6 0 0 ] { - - - } R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der R o tate En c o der N EW [ * * * * ] CO N F [ * * * * ] EN T ER 115200 EN T ER 115200 { - - - } EN T ER 115200 COM 1 - 3 : [ 1 1 5 2 0 0 ] [ 1 1 5 2 0 0 ] [ 1 1 5 2 0 0 ] P A S S [ * * * * ] User Manual 3 8 4 0 0 ] [ CO N F [ * * * * ] 1 9 2 0 0 ] { - - - } R o tate En c o der COM 1 - 3 : [ 1 1 5 2 0 0 ] [ 1 1 5 2 0 0 ] [ 1 1 5 2 0 0 ] P A S S [ * * * * ] [ 5 7 6 0 0 ] [ N EW [ * * * * ] 9 6 0 0 ] { - - - } 1 9 2 0 0 ] [ CO N F [ * * * * ] 4 8 0 0 ] { - - - } 9 6 0 0 ] [ CO N F [ * * * * ] 3 8 4 0 0 ] [ N EW [ * * * * ] COM 1 - 3 : [ P A S S [ * * * * ] 1 9 2 0 0 ] [ N EW [ * * * * ] 2 4 0 0 ] { - - - } 4 8 0 0 ] [ CO N F [ * * * * ] 1 2 0 0 ] { - - - } 2 4 0 0 ] [ CO N F [ * * * * ] 9 6 0 0 ] [ N EW [ * * * * ] COM 1 - 3 : [ P A S S [ * * * * ] 4 8 0 0 ] [ R o tate En c o der EN T ER C O M -3 1 2 0 0 ] [ CO N F [ * * * * ] 1 2 0 0 ] { - - - } EN T ER C O M -2 CO N F [ * * * * ] 2 4 0 0 ] [ N EW [ * * * * ] COM 1 - 3 : [ P A S S [ * * * * ] 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ * * * * ] EN T ER C O M -1 N EW [ * * * * ] COM 1 - 3 : [ P A S S [ * * * * ] 1 2 0 0 ] [ N EW [ * * * * ] N EW [ * * * * ] CO N F [ * * * * ] Rev. 1.1 - 04/07/12 { - - - } 49 / 54 SDC200/RDS 5.30 ELETTRONICA User PASSWORD - First entry { M a i n M e n u : [ A U D I O ] [ } [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] P res s enter to ac c es s the S y s tem m enu. [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] EN T ER [ B A C K ] 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ * * * * ] 1 2 0 0 ] { - - - } R o tate En c o der P res s enter to ac c es s the edit m ode of param eters . COM 1 - 3 : [ P A S S [ ! * * * ] EN T ER 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ * * * * ] [ 1 2 0 0 ] ] R o tate En c o der P res s enter to c onfirm the s elec ted param eter. R e p e a t th e p ro ce d u re b y p la cin g "!" in ste a d o f re m a in e d fre e fie ld s. [ B A C K ] COM 1 - 3 : [ P A S S [ ! ! ! ! ] EN T ER [ B A C K ] 1 2 0 0 ] [ N EW [ * * * * ] COM 1 - 3 : [ 1 2 0 0 ] [ N EW [ * * * * ] EN T ER B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] 1 2 0 0 ] ] R o tate En c o der 1 2 0 0 ] [ CO N F [ * * * * ] { U 1 2 0 0 ] P } P res s enter to ac c es s the edit m ode of param eter. 1 2 0 0 ] [ N EW [ A * * * ] EN T ER 50 / 54 [ P res s enter to c onfirm the s elec ted param eter. P A S S [ * * * * ] [ 1 2 0 0 ] [ CO N F [ * * * * ] Rev. 1.1 - 04/07/12 1 2 0 0 ] [ CO N F [ * * * * ] [ U 1 2 0 0 ] P ] R o tate En c o der P res s enter to c onfirm the s elec ted param eter. User Manual SDC200/RDS ELETTRONICA R e p e a t th e p ro ce d u re b y p la cin g th e ch a ra cte rs o f th e p a ssw o rd in fre e fie ld s. [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] 1 2 0 0 ] [ N EW [ A B C D ] EN T ER [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] CO N F [ * * * * ] [ B A C K ] [ U 1 2 0 0 ] P ] R o tate En c o der P res s enter to c onfirm the s elec ted param eter. 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ * * * * ] { U 1 2 0 0 ] P } EN T ER P res s enter to ac c es s the edit m ode of param eter. COM 1 - 3 : [ P A S S [ * * * * ] 1 2 0 0 ] [ 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ A * * * ] [ U 1 2 0 0 ] P ] R o tate En c o der EN T ER P res s enter to c onfirm the s elec ted param eter. R e p e a t th e p ro ce d u re b y p la cin g th e n e w ch a ra cte rs o f p a ssw o rd . [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] 1 2 0 0 ] [ N EW [ * * * * ] CO N F [ A B C D ] [ B A C K ] COM 1 - 3 : [ 1 2 0 0 ] [ N EW [ * * * * ] [ U 1 2 0 0 ] P ] EN T ER P res s enter to c onfirm the s elec ted param eter. P A S S [ * * * * ] 1 2 0 0 ] [ 1 2 0 0 ] [ CO N F [ * * * * ] [ U 1 2 0 0 ] P ] P a ssw o rd En try su cce e d e d [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ * * * * ] 1 2 0 0 ] [ E R R ] P a ssw o rd En try fa ile d User Manual Rev. 1.1 - 04/07/12 51 / 54 SDC200/RDS 5.31 ELETTRONICA User PASSWORD - Forgotten Password Recovery { M a i n } [ M e n u : [ A U D I O ] [ R D S B A C K ] [ S Y S T E M ] [ C L O C K ] [ V E R S . ] ] [ - - - - - - ] R o tate En c o der P res s enter to ac c es s the S y s tem m enu. [ B A C K ] COM 1 - 3 : [ P A S S [ * * * * ] EN T ER [ B A C K ] 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ * * * * ] [ 1 2 0 0 ] ] R o tate En c o der P res s enter to ac c es s the edit m ode of param eters . COM 1 - 3 : [ P A S S [ ? * * * ] EN T ER 1 2 0 0 ] [ N EW [ * * * * ] 1 2 0 0 ] [ CO N F [ * * * * ] [ 1 2 0 0 ] ] R o tate En c o der P res s enter to c onfirm the s elec ted param eter. R e p e a t th e p ro ce d u re b y p la cin g "? " in ste a d o f fre e fie ld s re m a in e d . [ B A C K ] COM 1 - 3 : [ P A S S [ ? ? ? ? ] EN T ER 1 2 0 0 ] [ CO N F [ * * * * ] [ 1 2 0 0 ] ] R o tate En c o der P res s enter to c onfirm the s elec ted param eter. [ K E Y - CO D E 1 2 0 0 ] [ N EW [ * * * * ] B A C K ] { 2 3 5 6 - 2 3 7 5 - 7 7 3 2 } E ntered in their res pec tive fields the c harac ters (?) w ill appear the c ode for pas s w ord rec overy . S e n t via F A X th e co d e to co n stru cto r to re ce ive th e fo rg o tte n p a ssw o rd . 52 / 54 Rev. 1.1 - 04/07/12 User Manual SDC200/RDS ELETTRONICA 6. Identification of the Modules The SDC200/RDS is made up of various modules linked to each other through connectors so as to make maintenance and any required module replacement easier. 6.1 Upper View The figure below shows the equipment upper view with the various components pointed out. figure 6.1 [1] [2] [3] [4] [5] Power Supply Panel Card CPU & I/O Card Display Card Audio Input Card User Manual Rev. 1.1 - 04/07/12 53 / 54 SDC200/RDS ELETTRONICA This page was intentionally left blank 54 / 54 Rev. 1.1 - 04/07/12 User Manual ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ R.V.R Elettronica S.p.A. Via del Fonditore, 2 / 2c Zona Industriale Roveri · 40138 Bologna · Italy Phone: +39 051 6010506 · Fax: +39 051 6011104 e-mail: [email protected] ·web: http://www.rvr.it ISO 9001:2000 certified since 2000 The RVR Logo, and others referenced RVR products and services are trademarks of RVR Elettronica S.p.A. in Italy, other countries or both. RVR ® 1998 all rights reserved. All other trademarks, trade names or logos used are property of their respective owners.