Download Manual - Microh
Transcript
TABLE OF F CONTENTS 1. INTRODU UCTION AND UN NPACKING 1 2. SAFTEY INSTRUCTIONS S 1-2 3. OPERATION INSTRUCTIONS 2-4 4. MOUNTIN NG AND INSTAL LLATION 4-5 5. DMX-512 CONTROL CON NNECTIONS 5 6. MENU NA AVIGATION 6-7 7. DMX CHA ANNELS 8 8. KEY FEA ATURES 9 9. TECHNIC CAL SPECIFICA ATIONS 9 10. MAINTE ENANCE AND CLEANING 10 1. INTROD DUCTION AND D UNPACKING G Thank you fo or purchasing the e MICROH LED STAR DRAPE. For your own saffety and knowled dge, please read d this manual beffore installing or operating the de evice. This manua al covers the imp portant informatio on on installation n and application ns. Please install and operate the fixture according g to instructions. Meanwhile, plea ase keep this ma nual for future re eference. RAPE is made off a cotton velour base for the fron nt and a polyeste er nylon based m material for the ba acking, The MICROH LED STAR DR and is fire tre eated for event use. u The fixture is s designed and manufactured m strrictly following C E standards, com mplying with international standard DMX5 512 protocol. This s fixture is applic cable but not limiited to large-scalle live performan nces, theater, stu udio, a discos. nightclubs and The MICROH LED STAR DR RAPE uses powe erful TRI (3in1) LED’s L which featu ess and stability. Please carefullyy ure high brightne unpack it wh hen you receive the t fixture and ch heck if it was dam maged during the e transportation. And please che eck whether the following items are included inside the box: Drape – One e Power Cord – One 5 Pin Control Ca able – One Controlller – 1 User Manua al – One 2. SAFTEY Y INSTRUCTIO ONS ory in perfect con ndition. In order to maintain this ccondition and to e ensure safe operration, it is absolu utely This device has left the facto or the user to folllow the safety ins structions and warning notes writtten in this user m manual. necessary fo If the device e has been expos sed to temperatu ure changes, do not n switch it on im mmediately. The e arising condenssation could dam mage the device. Leave L the device e switched off until it has reached d room temperatu ure, and is dry. 1 This device falls under protection-class I, therefore it is essential that the device be grounded. The electrical connection must be carried out by a qualified technician. The device should only be used with rate voltage and frequency. Make sure that the available voltage is not higher than 120V as stated at the end of this manual. Make sure the power cord is never crimped or damaged in any way, as this could cause shock and damage. If your power chord is damaged in any way, please purchase a new cable from your local MICROH dealer. Always disconnect power, when the device is not in use or before cleaning it. Never pull out the plug by tugging the power cord. During initial start-up, some smoke or smell may arise. This is a normal process, and does not necessarily mean that the device is defective. It should decrease gradually. Please do not project the beam onto combustible substances. Fixtures cannot be installed on or near combustible substances. Keep more than 50cm distance from wall for proper ventilation and air flow. If your fixture is or has become damaged in any way, it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard. 3. OPERATION INSTRUCTIONS - Do not turn on the fixture if it has been through severe temperature differences. Damage may occur to the fixture. Wait until unit is at room temperature to operate. - The unit should be protected from any tremor or agitation during transport. - Do not expose the fixture in any excessive heat, moisture or any environment with too much dust when installing. Do not lay any power cables on the floor. It may cause electronic shock or damage to persons or equipment. - Make sure to attach the safety chain and ensure the screws are properly screwed in when installing the fixture. - Make sure the lens is in good condition. It is recommended to replace the unit if there are any damages or severe scratches. - Make sure the fixture is operated and installed by qualified personnel. - Keep the original packaging in case of defective product. - Any non-manufacturer additions, modifications or changes in any way will void all warranty. - Please do not attempt to open unit. It is only to be serviced by an authorized technician. If this occurs, or is apparent, the warranty will be voided. - The fixture’s warranty will be voided if there are any malfunctions from not following the user manual or any illegal operation (shock short circuit, electronic shock, lamp broke, etc.) 2 -This fixture is equipped with 6 operating modes. Master/Slave, DMX, Sound Active, Manual Mode, Colour Fade and Colour Chase. MASTER/SLAVE MODE - By connecting either the 3 or 5 pin DMX, you can daisy chain up to 30 units on master/ slave mode. Daisy chain the fixtures together by plugging from the DMX output of the first fixture into the DMX input of the second fixture, and so on… - On your Master fixture set the unit to SOUND, MANUAL, COLOUR FADE or COLOUR CHASE control and select one of the internal programs. - All slave lights must be set “A001” DMX - From the main menu select “ADDR” and press ENTER. By using the UP and DOWN buttons, you can set the DMX address. Press ENTER when number is reached. - Once the address is set, leave the unit powered on for 3 minutes in order to store the address within the unit so that it returns to that address when powered off/on. SOUND ACTIVE MODE - From the main menu, select either “SOUA” or “SOUF”. - SOUA mode with chase randomly through the internal programs activated by sound. - SOUF mode will chase through 7 individual full bar colours. - To adjust the audio sensitivity, select “SEnS” from the main menu and press ENTER. Using the UP and DOWN buttons select number 0 through 15. (0 being the lowest, and 15 being the highest sensitivity.) MANUAL MODE - From the main menu, select “rLXX”, “gLXX”, and “bLxx” and use the UP and DOWN buttons to adjust each individual colour from numbers 0 through 15. (0 being off, and 15 being the full intensity.) This will create a custom colour mix of your choosing. COLOUR FADE - From the main menu, select “FAXX” and use the UP and DOWN buttons to select the speed of the colour fade. AUTO COLOUR CHANGE (7 COLOUR CHANGE) - From the main menu, select “ASXX” and use the UP and DOWN buttons to select the speed of colour change. (0 being the slowest, 15 being the fastest.) CHASE MODE - From the main menu, select “CEXX” and use the UP and DOWN buttons to select your desired chase from numbers 1 through 15. - To adjust the speed of the chase, select “CSXX” from the main menu and use the UP and DOWN buttons to select speeds 1 to 15. (1 being the slowest, and 15 being the fastest.) STROBE (FLASH) - To apply strobe (FLASH) to one of the auto modes, select “FLxx” from the main menu and use the UP and DOWN buttons to select your desired flash rate from 1 to 15. (1 being the slowest, and 15 being the fastest.) 3 4. MOUNT TING AND INST TALLATION Caution: Fo or added protection, mount the fix xtures in areas outside walking pa aths, seating are eas, or in areas w were the fixture m might be reached by unauthorized personnel. Befo ore mounting the fixture to any su urface, make sure e that the installa ation area can ho old a minimum po oint load of 10 tim mes the device’s weight. Fixture in nstallation must always be securred with a second dary safety attacchment, such as an appropriate a safetty cable. Never stand s directly below the device w when mounting, re emoving, or servvicing the fixture. Whether installing inverted on o a truss or ceiling, Be sure this fixture is kept aw way from any and d all flammable m materials (decora ation etc.). Always s use and install the supplied saffety cable as a sa afety measure to o prevent acciden ntal damage and d/or injury in the e event the mounting g fails. Mounting Points: P Overhead d mounting requiires extensive ex xperience, includ ding calculating w working load limitts. A knowledge of the installation material m being us sed, and periodic c safety inspectio on of all installatio on material and tthe fixture are all imperative and should only be perfo ormed by a qualified technician. Improper installa ation can result in n bodily injury an nd damage. Be sure to complete c all riggin ng and installatio on procedures be efore connecting the main powerr cord to the apprropriate wall outlet. 4 Picture of back b of unit hun ng with pipe & drape. d Regardless of the rigging op ption you choose for your MICROH LED STAR DR RAPE, always be e sure to secure your fixture with a safety cable. The fixture prov vides a built-in rig gging point for a safety cable on the hanging braccket as illustrated above. Be sure e to only use the e designated rigging point for the safety cable. 5. DMX-512 CONTROL CONNECTION C NS This fixture complies c with intternational USITT T DMX standards and can be use ed with either a 3 pin or 5 pin DM MX connector. Plug in the provided d 3 pin XLR cable e to the female 3-pin 3 XLR output of your controlle er and the other sside to the male 3-pin XLR input of the LED STAR DRAPE. D To conn nect the units to DMX, you must daisy d chain the ffixtures together as referred in the e diagram below w. Always end your DMX-512 connection c with a DMX terminator. For installatiions where the DMX D cable has to o run a long dista ance, or is in an e electrically noisyy environment, it is recommended d to use a DMX terminator. t This helps in preventiing corruption of the digital contro ol signal by electtrical noise. The DMX terminator is simply an XL LR plug with a 12 20 Ω resistor con nnected between n pins 2 and 3,wh hich is then plugg ged into the outp put XLR socket o of the last fixture in n the chain. Plea ase see illustratio ons below. 12 20Ω 2 3 1 PIN 3 PIN 2 5 6. MENU NAVIGATION N 6 7 7. DMX CH HANNEL 8 8. KEY FEATURES - 128 x ¼ Watt 5mm Tri Colour SMD 50/50 LEDs - 3 XLR Input & Output - PowerCon AC Input - All Metal Grommets on all 4 Sides for Mounting - Heavy Duty Velcro to Attach Multiple Drapes for Seamless Look - Digital 4 Button Display - Stand Alone, Master/Slave DMX & Auto - RGB: Infinite Colour Mixing Possibility - Effects: RGB Colour Mixing, Strobe, Bright Burst Effect, Auto Programs - Includes Controller and Control Cable 9. TECHNICAL SPECIFICATIONS LAMP: 128 x ¼ Watt 5mm Tri Colour SMD 50/50 LEDs VOLTAGE: 120VAC 60Hz FUSE: 250VAC 2A MAX: 240W DIMENSIONS: 13’ x 19.5’ / 396 x 594 cm NET WEIGHT: 37.1 lbs / 16.83 kgs WARRANTY: 1 Year Limited Warranty 9 10. MAINT TENANCE AND D CLEANING The following points have to be considered during d the inspec ction: 1) All screw ws for installing th he device, or partts of the device must m be tightly co onnected, and m must not be corro oded. 2) There mu ust not be any de eformations on th he housing, colour lenses, fixatio ons or installation n spots (ceiling, ssuspension, trusssing). 3) Mechanically moved partts must not show w any traces of wearing w and mustt not rotate with u unbalances. ctric power supply y cables must no ot show any dam mage, material fattigue or sedimen nts. 4)The elec Further instrructions depending on the installa ation spot and us sage must be ha ndled by a skille d installer or tech hnician. Any safe ety issues must be resolved. In order to keep k the fixture in n good condition and extend the life, l we suggest regular cleaning to the fixture. 1) Clean the e inside and outs side lens each week to avoid the light output from m darkening due to accumulation of dust, dirt, etc.. 2) Clean the e fan each week. 3) A detaile ed electrical chec ck by approved technician every three months is advised. Ensure e the circuit conta acts are in good conditio on, and prevent from f overheating g. 4) Do not ma achine wash. Pro ofessional dry clean c only. (Flam me Retardant Du uration: 10 Wash hes) We recomm mend a frequent cleaning c of the de evice. Please use a moist, lint- fre ee cloth. Never u use alcohol or so olvents. There are no o serviceable parts inside the dev vice. Please refe er to the instructio ons under “Insta llation instruction ns”. Should you need any spare parts, please ord der genuine MICROH parts from your local dealer. IF YOU SHO OULD EXPERIE ENCE ANY PROB BLEMS OR ISSU UES PLEASE C CONTACT MICRO OH PROFESSIO ONAL PRODUCTS BY EMAIL AT info@microhpro i o.com In the eventt that your unit is defective in any a way, please e contact your lo ocal dealer to o obtain an RA number for servic ce repair. ER – MICROH be elieves that the information contained within tthis user manua al is accurate. H However, Microh h is DISCLAIME not respons sible for any errror or addendum ms to this manu ual. If you have any comments or general suggestions on how this manual can n be improved please p contact in nfo@microhpro o.com. Thank yo ou. 10