Download WinTCD User Manual
Transcript
Preparing the System for Monitoring CD T WinTCD - [Acquiring data for Jones, W] Acq Exam Settings View Doppler Configuration Indicators Report Window Help win CD T WinTCD - [Acquiring data for Jones, W] Acq Exam Settings View Doppler Configuration Indicators Report Window Help win V VI SYS L T H C V V H E 2. Click the Right mouse button. CH 1 (S1) - 2 Mhz PW : MCA R 33 -1 Mean 50 15 - SV SYS - - 0 -50 Event List * Event Descriptor Time -100 9 PI DIA Trend Window Ch1: SYS 100 50 50 Ch1: SYS 100 << >> Ch1: DIA Ch1: DIA 13:00:00 Vessel Labels Nic Vue 14:00:00 SoundTrak On/Off Envelope Spectra On/Off Units WinTCD - [Acquiring 9:09 A.M. These 5 keys correspond to the 5 softkeys on the screen display. S1 S2 S3 SAVE FREEZE PRINT PROBE _ DIRECTION + _ WINDOW MENU ESCAPE ENTER + _ + SWEEP _ + GAIN + _ DEPTH S5 ZERO + _ S4 MUTE DELETE _ AMPLITUDE 4. Repeat until all five S-keys have been assigned a specific function. 50 Depth 100 SAMPLE 3. Click on the function you want to assign to the selected softkey (Figure 3). X REC 100% cm/s Start 1. Position the mouse pointer over the softkey displayed towards the bottom of the Acquisition window (Figure 2). _ TM R E + SCALE Figure 1: The softkeys displayed on the screen can be clicked on to execute the action or the corresponding S-key on the remote control can be pressed to execute the action. H E V Example If, for example, the S1 key is currently assigned to the Vessel Labels function and you want to change it to Units, use the Right mouse key and click on the Vessel Labels softkey and then click on Units from the options menu. The first softkey (S1) will now read Units and pressing the S1 key on the Remote Control will alternate the Flow Velocity Scale between cm/s and kHz. Note: You can not assign the same function to multiple S-keys with the mouse. If you want to reassign a function, you must first remove the function from the current key. V You can select, from a menu of options, the functions of the five keys (S1 - S5) on the Remote Control (Figure 1). These five keys allow you to quickly execute the chosen function by simply pressing the corresponding key (S1 - S5) on the Remote Control or by clicking on the displayed softkey. VI SYS L T H C V Set the Remote Control S1 - S5 key functions Note: Alternatively the S-keys can be configured by selecting the function Configure S-keys out of the Configuration menu. In the pop up dialog box a set of S-keys can be defined for each of the three operation windows (main window, freeze window, and review window). See next page. _ X TM R E REC 100% CH 1 (S1) - 2 Mhz PW : MCA R 33 cm/s 50 -1 Depth Mean 100 50 15 - SV SYS - - 0 -50 Event List * Event Descriptor Time -100 9 PI DIA Trend Window Ch1: SYS 100 50 50 Ch1: SYS 100 << >> Ch1: DIA Ch1: DIA 13:00:00 Vessel Labels Start Nic Vue 14:00:00 SoundTrak On/Off Envelope Spectra On/Off WinTCD - [Acquiring Units 9:09 A.M. Figure 2: Position the mouse pointer over the displayed softkey you want to define and then click the Right mouse button. Indicators On/Off Envelope Filter Down Filter Up Toggle PW/CW SoundTrak On/Off Spectra On/Off Units Vessel Labels Graphics Report Parameter Boxes Indicators Settings Indicators Reset Count Curve Recording On/Off Settings Manager Boost Mode Squelch On/Off Flow Separation On/Off Export SoundTrak Multi Depths Link On/Off MD Expand Depths MD Contract Depths Inc. Rx Pulse Width Dec. Rx Pulse Width M-Mode Display Options Display Range Inc. Tx Pulse Width Dec. Tx Pulse Width Tx/Rx Linkage On/Off Calculate VMR (H-Cursors) Calculate VMR (A-Cursors) Audio Playback Scale Set Set Delta Mean S-Markers I-Markers Noise Reduction Fast Curve Window Figure 3: Click on the function you want to assign to the selected key. (List shown is an example from the monitoring mode) S5-5